Hilti Pra 90 User manual

PRA 90
English
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of signs used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used in combination with a symbol:
DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal
injury or damage to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use
Instructions for use and other useful information
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text.
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section.
These characters are intended to specifically draw your attention to certain points when handling
the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Only use in enclosed spaces
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

2 English
▶Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Automatic tripod PRA 90
Generation 01
Serial no.
2 Safety
2.1 Safety precautions
Note
In addition to the information relevant to safety provided in the individual sections of these operating
instructions and the information provided in the operating instructions of whichever type of rotating
laser is being used, the following instructions must also be strictly observed at all times.
General safety instructions
Do not render safety devices ineffective and do not remove information and warning notices.
Proper preparation of the working area
▶Secure the site in which you are taking measurements and take care to avoid directing the beam
towards other persons or towards yourself when setting up the appliance.
▶When performing alignment work on ladders, avoid postures to which you are unaccustomed.
Make sure you work from a safe stance and stay in balance at all times.
▶Ensure that the tool is set up on a stable, level surface (not subject to vibration).
▶Use the tool only within its specified limits.
▶Take care to ensure that no parts of the body are located under the tripod when the tripod is set
up or in operation.
▶Do not use the tripod as a hoist or lifting aid.
▶Keep children away. Keep other persons away from the working area.
▶When setting up the tripod in enclosed spaces (indoor rooms), check the suitability of the floor on
which it stands, as the tripod could gouge scratches into the floor.
Electromagnetic compatibility
▶Although the device complies with the strict requirements of the applicable directives, Hilti cannot
entirely rule out the possibility of interference to the device caused by powerful electromagnetic radiation,
possibly leading to incorrect operation. Check the accuracy of the tool by taking measurements by other
means when working under such conditions or if you are unsure. Likewise, Hilti cannot rule out the
possibility of interference with other devices (e.g. aircraft navigation equipment).
General safety measures
▶Check the condition of the device before use. If the device is found to be damaged, have it repaired at a
Hilti Service Center.
▶Always keep the PRA 90 threaded rod free from objects of any kind, including parts of the body or
dirt.
▶Do not put your fingers or other parts of the body into the tubes of the tripod legs or other points
at which injuries may be caused.
▶Although the appliance is designed for use on job sites under tough conditions, it should be
handled with care, in the same way as other electrical appliances.
▶Although the device is protected to prevent entry of dampness, it should be wiped dry each time
before being put away in its transport container.
▶Only use the AC adapter for connecting to the power supply.
▶Ensure that the appliance and AC adapter do not present an obstacle that could lead to a risk of
tripping or personal injury.
▶Ensure that the workplace is well lit.
▶Check extension cords at regular intervals and replace them if found to be damaged. Do not touch
the AC adapter if the extension cord or AC adapter are damaged while working. Disconnect the
supply cord plug from the power outlet. Damaged supply cords or extension cords present a risk of
electric shock.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 3
▶Avoid body contact with earthed or grounded surfaces such as pipes, radiators, cookers, stoves
and refrigerators. There is an increased risk of electric shock if your body is grounded.
▶Do not expose the supply cord to heat, oil or sharp edges.
▶Never operate the AC adapter when it is dirty or wet. Dust (especially dust from conductive
materials) or dampness adhering to the surface of the AC adapter may, under unfavorable
conditions, lead to electric shock. Dirty or dusty tools or appliances should thus be checked by
Hilti Service at regular intervals, especially if used frequently for working on conductive materials.
▶Avoid touching the contacts.
▶Use the carry strap supplied with the tripod to make it easier to carry the PRA 90. When transporting
the PRA 90, take care not to allow the tripod to cause injury either to yourself or to other persons.
Particular care should be taken in checking the position of the points at the ends of the legs during
transportation.
▶When you are finished using the PRA 90, always make sure that the threaded column is fully wound
down before the tripod legs are folded together.
Use and care of battery-powered tools
▶Use only batteries of the type approved for use with the applicable tool. Use of other batteries or
use of the batteries for purposes for which they are not intended presents a risk of fire and explosion.
▶Do not expose batteries to high temperatures and keep them away from fire. There is a risk of
explosion.
▶Do not disassemble, squash or incinerate batteries and do not subject them to temperatures over
80 °C (176 °F). This presents a risk of fire, explosion or injury through contact with caustic substances.
▶Do not allow moisture to enter the battery. Moisture in the interior of the device may cause a short
circuit and chemical reactions resulting in burns to the skin or fire.
▶Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.
▶Avoid short circuiting the battery terminals. Check that the battery terminals and the terminals in
the power tool are free from foreign objects before inserting the battery in the tool. Short circuiting
the battery terminals presents a risk of fire, explosion and chemical burns.
▶Never continue to use or attempt to charge damaged batteries, e.g. batteries with cracks, broken
parts, bent or pushed-in / pulled-out contacts).
▶Only use the AC adapter PRA 85 or the motor vehicle power adapter PRA 86.for operating the
appliance and charging the battery. The appliance may otherwise be damaged.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

4 English
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 5
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

6 English
3 Description
3.1 Overview of the product
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 7
@Laser adapter 5/8"
;Tripod head
=Extendable supports
%Control panel
&Charging display control panel
(Height regulation control panel
)LED display control panel
+Control panel on/off button
§Battery compartment
/Optional remote control unit PRA 92
:PRA 92 LED display
∙PRA 92 On/Off button
$PRA 92 height regulation
£Rotating laser
3.2 Intended use
The product described is an automatic tripod onto which a rotating laser can be fitted. The tripod can be
moved in height using the control panel or a remote control unit. Using the tripod and the rotating laser
fitted to it, a horizontal laser plane can be established which is directed onto a particular target height, meter
marks can be transmitted and horizontal heights aligned and checked.
The tripod can be operated in 3 different ways: with PRA 30 remote control/laser receiver (in combination
with PR 30HVS rotating laser for automatic alignment and monitoring), without remote control and with
remote control unit PRA 92.
▶Use only the Hilti Liion battery PRA 84 for this product.
▶For these batteries, use only the Hilti PRA 85 AC adapter.
3.3 Automatic alignment
The tripod can be automatically aligned with the Hilti rotating lasers PR 30HVS, PR 35, PR 300HV2S or PRI
36. We recommend using the Hilti rotating laser PR 30HVS. This was specially matched to the PRA 90 and
has a three-device communication system between tripod, rotating laser and the associated remote control
unit PRA 30.
Using these three components together, a laser plane can be aligned onto a precise point automatically.
Only the target height has to be indicated using the PRA 30, and the PRA 90 directs the laser plane of the
PR 30HVS rotating laser exactly to that height.
If other rotating lasers are used, you will need the PRA 92 remote control unit in order to move the tripod up
and down. Automatic alignment is therefore not possible.
3.4 Charge state display
During the charging operation in the device, during operation
Status Meaning
4 LEDs light. • Charge state 100%
3 LEDs light, 1 LED blinks. • Charge state ≥ 75%
2 LEDs light, 1 LED blinks. • Charge state ≥ 50%
1 LED lights, 1 LED blinks. • Charge state ≥ 25%
1 LED blinks. • Charge state < 25%
During the charging operation outside the tool
Status Meaning
Red LED on the battery lights. • The battery is charging
Red LED on the battery does not light. • Charge state 100%
3.5 Items supplied
Automatic tripod PRA 90, Li-ion battery PRA 84, AC adapter PRA 85, carry strap, operating instructions,
manufacturer certificate.
You can find other system products approved for your product at your local Hilti Center or online at:
www.hilti.group.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

8 English
4 Technical data
4.1 Technical data PRA 90
Communication range with PRA 30 in direction of the tripod con-
trol panel
164 ft
Communication range with PRA 30 to the side of, or in the oppo-
site direction of, the tripod control panel
98.43 ft
Transportation length 37 in
Weight 18 lb
Carry weight ≤ 11 lb
Maximum height (with rotating laser) 6.4 ft
Minimum height (with rotating laser) 3.18 ft
Total travel 21 in
Smallest travel 0.010 in
Operating temperature −4 ℉ …140 ℉
Storage temperature −13 ℉ …140 ℉
Protection class IP 56
Tripod thread ⁵⁄₈" x 11 mm (0.43")
4.2 Technical data PRA 84
Rated voltage 7.2 V
Maximum voltage during operation or during charging while in
operation
13 V
Charging time at 32 °C (+90 °F) 130 min
Operating temperature −4 ℉ …122 ℉
Storage temperature (dry) −13 ℉ …140 ℉
Charging temperature 32 ℉ …104 ℉
Weight 0.7 lb
4.3 Technical data PRA 85
Mains power supply 115 V …230 V
AC frequency 47 Hz …63 Hz
Rated power 36 W
Rated voltage 12 V
Operating temperature 32 ℉ …104 ℉
Storage temperature (dry) −13 ℉ …140 ℉
Weight 0.51 lb
4.4 Technical data PRA 92
Infrared communication type 2.4 GHz
Power source 2 AA batteries
Operating temperature −4 ℉ …122 ℉
Storage temperature −13 ℉ …140 ℉
5 Before use
5.1 Charging the battery
Note
This tripod must only be operated with the Hilti battery PRA 84.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 9
▶Charge the batteries fully before using them for the first time.
5.1.1 Charging the battery in the tool
WARNING
Electrical hazards. If liquids penetrate the tool, they may cause the AC adapter to short circuit and
explode. This may result in serious injury and cause burns!
▶The PRA 85 AC adapter is for indoor use only.
1. Place the battery into the battery compartment.
2. Rotate the socket cover so that the charging socket on the battery can be seen.
3. Plug the cord from the AC adapter or motor vehicle power adapter into the battery.
4. Connect the AC adapter or the motor vehicle power adapter to the power supply.
Note
The current charge status is shown by the battery display on the tripod when it is switched on.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

10 English
5.1.2 Charging the battery externally (not in the tool)
WARNING
Electrical hazards. If liquids penetrate the tool, they may cause the AC adapter to short circuit and
explode. This may result in serious injury and cause burns!
▶The PRA 85 AC adapter is for indoor use only.
1. Remove the battery from the tripod and plug in the connector of the AC adapter or the motor vehicle
power adapter.
2. Connect the AC adapter or the motor vehicle power adapter to the power supply.
Note
The red LED on the battery lights while charging is in progress.
5.1.3 Charging the battery while the tool is in operation
1. Turn the cover so that the charging socket on the battery can be seen.
2. Plug the connection of the AC adapter into the battery.
◁The tripod works during the charging operation and the charge state is displayed by the LEDs on the
tripod.
5.2 Inserting the battery
Note
Check that the terminals on the battery and on the tripod are free from foreign objects before inserting
the battery.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 11
1. Slide the battery into the holder on the tripod.
2. Turn the catch two notches in a clockwise direction until the “locked” symbol appears.
5.3 Removing the battery
1. Turn the catch two notches in an counter-clockwise direction until the “unlocked” symbol appears
2. Remove the battery from the tool.
5.4 Pairing
Note
In order to use the tripod and remote control unit, these must be exclusively assigned to each other.
▶Press the On/Off buttons on the remote control unit and the tripod simultaneously and keep them
pressed for at least 3 seconds. If the pairing with the PRA 92 is successful, the LEDs on both tools light
simultaneously.
6 Operation
6.1 Fitting rotating laser to tripod
Note
Only fit devices that weigh no more than 5 kg (11 lbs).
▶Screw the rotating laser onto the tripod.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

12 English
6.2 Working with the PRA 30 tripod and remote control unit
Note
Before use, the remote control unit must be paired with the tripod in order to enable communication
between the two appliances.
The PR 30HVS rotating laser should also have been paired separately with the PRA 30. In this way,
three-device pairing is established which is essential for an automatic alignment of the laser plane.
1. Press the On/Off button on the tripod and on the remote control unit and hold the buttons pressed
simultaneously for at least 3 seconds.
◁Successful pairing is shown by a chain on the PRA 30 display, while on the PRA 90 all LEDs are
blinking. After this is displayed, both tools switch off automatically.
2. Press the On/Off buttons on the PRA 90, PRA 30 and PR 30HVS..
◁On the PRA 30 remote control unit display, the rotating laser including tripod is shown, with the active
radio connection being depicted as a wave.
◁If there is no active radio connection, a warning triangle appears on the display instead of the wave.
6.3 Align using the automatic tripod PRA 90
Note
This function is only available with the automatic tripod PRA 90.
When used for the first time, the laser receiver PRA 30 must be paired with the tripod
With the optional automatic tripod PRA 90, the height of the laser plane can be manually or
automatically adjusted to the desired height.
1. Mount the tool on the automatic tripod PRA 90.
2. Switch on the rotating laser, the automatic tripod and the laser receiver.
3. Now align the height of the laser plane manually → page 13 or automatically → page 14.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 13
6.3.1 Manual alignment
▶Press the +/- buttons on the laser receiver or the arrow buttons on the PRA 90 to shift the horizontal
plane up or down (parallel).
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

14 English
6.3.2 Automatic alignment
1. Keep the receiver side of the laser receiver at the desired target height and towards the PRA 90 control
panel. Hold the laser receiver still while alignment is taking place and take care to ensure that the line of
sight between the laser receiver and the tool is not obstructed.
2. Press the “Automatic alignment” button on the laser receiver twice in quick succession (double-click).
Double-click the button again to complete the procedure.
◁This double-click starts the process of bringing the laser plane into alignment, i.e. the tripod elevates
or lowers itself to the required height. During this time, an acoustic signal sounds continuously. As
soon as the laser beam strikes the detection area of the laser receiver, the beam moves to the position
of the marking notch (reference plane). After the position has been reached and the rotating laser has
leveled itself, a signal tone with a duration of 5 seconds indicates that the process is complete. The
“Automatic alignment” symbol is then also no longer shown.
3. Check the height settings in the display.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 15
4. Remove the laser receiver.
Note
If the automatic alignment process was not successful, short signal tones are emitted and the
“Automatic alignment” symbol goes out.
6.4 Working with the tripod without the remote control unit
1. Press the On/Off button on the tripod.
◁The tripod switches on.
2. On the control panel of the tripod, press the appropriate arrow buttons in order to move the tripod
upwards or downwards.
6.5 Working with the PRA 92 tripod and remote control unit (accessory)
Note
Before use, the remote control unit must be paired with the tripod in order to enable communication
between the two appliances.
1. Press the On/Off button on the tripod and on the remote control unit and hold the buttons pressed
simultaneously for at least 3 seconds.
◁Successful pairing is indicated by the LEDs on both tools lighting at the same time.
2. Align the control panel of the tripod towards the PRA 92.
3. On the keypad of the remote control unit, press the appropriate arrow buttons in order to move the tripod
upwards or downwards.
◁When the tripod is moved, most rotating lasers either display “Shock” and adjust their level, or they
show “Shock” and switch off.
◁With the Hilti models PRE 3, PR 20,PR 2HVS, PR 25, PR 26 and PRE 38, there is only a leveling
phase in the first minute. In the leveling phase, the laser plane can no longer be seen for a short time.
7 Care and maintenance
Note
Observe the temperature limits of 25 °C (-13 °F) to +60 °C (140 °F) if you keep your equipment inside
a motor vehicle.
• Always keep the threaded rod free from coarse dirt and concrete residues.
• Use only a clean, soft cloth for cleaning. If necessary, moisten the cloth slightly with pure alcohol or
water. Do not use any other liquids as these may affect the plastic parts.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

16 English
8 Transport and storage
Transport
CAUTION
Unintentional start-up during transportation. If batteries are left inserted, the tool may start up
unintentionally during transportation and the therefore may be damaged.
▶Always transport the tool with the batteries removed.
• After use, wind the threaded rod down fully.
• Remove the battery.
• Only now fold in the tripod legs.
• For transporting or shipping your equipment, either use the Hilti shipping box, the Hilti transport pouch
or an equivalent form of packaging.
• Always check the accuracy of the equipment before it is used after a prolonged period of transportation.
Storage
CAUTION
Unintentional damage caused by defective batteries. Leaking batteries may damage the tool.
▶Always store the tool without the batteries inserted.
• Store tools and appliances in a dry place where they cannot be accessed by children or unauthorized
persons.
• Remove the tool from its case if it has become wet. Tools, carrying cases and accessories should be
dried and cleaned at a maximum temperature of 40 °C (104 °F).
• Repack and store the equipment only once it is completely dry.
• Always check the accuracy of the equipment before it is used after a prolonged period of storage.
• Store the battery in a place that is as cool and dry as possible.
Never store the battery where it is exposed to direct sunlight or sources of heat, e.g. on heaters /
radiators or behind glass.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
9.1 Troubleshooting
Trouble or fault Possible cause Action to be taken
Tripod does not respond. Tripod not switched on. ▶Switch on tripod.
Tripod not paired. ▶Pair the remote control unit with
the tripod.
Batteries in the PRA 92 empty. ▶Replace the batteries.
Tripod cannot be switched
on.
Battery not fully inserted or empty. ▶Insert the battery so that a
“click” is heard or charge the
battery.
Automatic alignment not suc-
cessful.
The desired height is outside the
maximum possible setting height.
▶Check the adjustment height.
Excessive vibration from external
influences.
▶Completely unfold the tripod
and check that it stands firmly.
Tripod is out of range. ▶Approach the tripod more
closely with the remote control
unit and/or align the control
panel towards the remote
control unit.
Setting the monitoring mode
is not successful.
The desired height is outside the
maximum possible setting height.
▶Check the adjustment height.
Excessive vibration from external
influences.
▶Completely unfold the tripod
and check that it stands firmly.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

English 17
Trouble or fault Possible cause Action to be taken
Setting the monitoring mode
is not successful.
Tripod is out of range. ▶Approach the tripod more
closely with the remote control
unit and/or align the control
panel towards the remote
control unit.
10 Disposal
WARNING
Risk of injury. Hazards presented by improper disposal.
▶Improper disposal of the equipment may have the following consequences: The burning of plastic
components generates toxic fumes which may present a health hazard. Batteries may explode
if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or
environmental pollution. Careless disposal may permit unauthorized and improper use of the
equipment. This may result in serious personal injury, injury to third parties and pollution of the
environment.
▶Dispose of defective batteries right away. Keep them out of reach of children. Do not disassemble
or incinerate the batteries.
▶Batteries that have reached the end of their life must be disposed of in accordance with national
regulations or returned to Hilti.
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
11 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about the warranty conditions.
12 FCC statement (applicable in US) / IC statement (applicable in Canada)
CAUTION
Interference to radio reception Use of the product in residential areas may cause interference to
radio reception.
▶This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause interference to radio communications.
▶However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by taking the following measures: Re-orient or relocate the receiving antenna.
Increase the distance between the equipment and receiver. Consult the dealer or an experienced
TV/radio technician for assistance.
Changes or modifications not expressly approved by Hilti may restrict the user’s authorization to operate
the equipment.
This device is in compliance with paragraph 15 of the FCC Regulations RSS210 of the IC Regulations.
Operation is subject to the following two conditions:
This device shall cause no harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02

Printed: 21.07.2017 | Doc-Nr: PUB / 5136610 / 000 / 02