Hilti SI-AT-A22 User manual

SIATA22
English 1
Dansk 15
Svenska 28
Norsk 42
Suomi 56
Eesti 69
Latviešu 83
Lietuvių 97
Русский 111
Українська 126
Қазақ 142
Türkçe 156
ﻋﺮﺑﻲ 170
日本語 184
한국어 198
繁體中文 211
中文 223
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

1
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

2
3
4
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

5
6
7
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

8
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

SIATA22
en Originaloperatinginstructions....................................... 1
da Originalbrugsanvisning .......................................... 15
sv Originalbruksanvisning........................................... 28
no Originalbruksanvisning .......................................... 42
fi Alkuperäisetohjeet ............................................. 56
et Originaalkasutusjuhend .......................................... 69
lv Oriģinālālietošanasinstrukcija ..................................... 83
lt Originalinaudojimoinstrukcija...................................... 97
ru Оригинальноеруководствопоэксплуатации ........................... 111
uk Оригінальнаінструкціязексплуатації ................................ 126
kk Түпнұсқапайдаланубойыншанұсқаулық .............................142
tr Orijinalkullanımkılavuzu ......................................... 156
ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 170
ja オリジナル取扱説明書 . ........................................... 184
ko 오리지널 사용설명서 . . ........................................... 198
zh 原始操作說明 .................................................. 211
cn 原版操作说明 .................................................. 223
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and ontheproduct.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that may occur when handling or using the product. The following signal
words are used in combination with a symbol:
DANGER! Draws attention to an imminent hazard that will lead to serious personal injury or
fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal
injury or material damage.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use
Instructions for use and other useful information
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering reflects the sequence of operations shown in the illustrationsandmaydeviate
from the steps described in the text.
Item reference numbers are used in the overview illustration and refer to the numbers used in
the key in the product overview section.
This symbol is intended to draw special attention to certain points when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Direct current (DC)
Do not dispose of electric tools, machines or appliances together with household waste.
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
▶Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire abouttheproduct.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

2English
Product information
Type SIATA22
Generation 01
Serial no.
2Safety
2.1 Safety precautions
▶Observe the safety precautions in the operating instructions for the wrench.
3 Description
3.1 Adaptive torque module 1
@Control panel buttons
;LCD display
=Indicator LEDs
%Bar code scanner
&Release button
(USB connector
)USB connector cover (shown open in the
illustration)
3.2 Control panel buttons 2
@OK button
;Left arrow button
=Right arrow button
%Lock button
&Scan button
3.3 Intended use
The product described is an electronic module that can be used with Hilti impact wrenches of the
types SI… …ATA22 (“…” = any character) to tighten threaded fasteners under controlled conditions,
thereby safeguarding the quality of the bolted connection (SafeSet technology). A record of the work
carried out is saved in the torque module and can be read out, for documentation purposes, using the
PROFIS Adaptive Torque PC application.
▶Use only Hilti Liion batteries of the B 22 series with this product.
▶Use only the Hilti battery chargers of the C4/36 series to charge these batteries.
▶Useonlylong1/2″impactsockets(Hilti, type SI-S 1/2″ L) for tightening anchor fastenings.
3.4 Indicator LEDs
The various statuses of the LEDs on both sides of the module provide the following information or indicate
the applicable operating states:
Status Meaning
The indicator LEDs light green. • When scanning: The bar code or QR code has
been recognized.
• When tightening, after the impact wrench has
been switched off automatically: The tightening
operation was completed successfully.
The indicator LEDs light red. • When scanning: The bar code or QR code was
not recognized.
• When tightening, after the impact wrench
switches off: The bolt fastening could not
be tightened in accordance with the selected
settings. The reason for this, for example,
could be that the impact wrench was switched
off manually before the correct torque was
achieved.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 3
Status Meaning
The indicator LEDs blink green. • It has been detected that the bolt fastening
was already tightened and then subsequently
released. The bolt fastening was therefore
retightened according to defined parameters
and the tightening operation was completed
successfully.
3.5 Tone generator
The tone generator incorporated in the torque module emits 2 different signal tones that provide audible
feedback.
Signal tones and their meaning
• Long tone: Confirmation signal (OK / operation completed successfully)
• 3 short tones: Warning signal (not OK / operation was aborted)
Note
The volume of the signal tone can be adjusted or the tone can be muted completely in the basic
settings menu.
3.6 USB connector
The USB connector can be used to connect the adaptive torque module to a PC. The
PROFIS Adaptive Torque PC application provides, among others, the following functions:
• Adding new data records for new threaded fasteners
• Changing / updating existing data records
• Deactivating / activating the documentation function
• Loading the report from the documentation function
• Setting the clock in the torque module
Note
Further information can be found in the documentation for the PROFIS Adaptive Torque software.
3.7 Items supplied
Adaptive torque module, operating instructions, quick-start instructions, USB cable.
Note
You can find other system products approved for use with your product at your local Hilti Center or
online at: www.hilti.com.
4 Technical data
Weight in accordance with EPTA
procedure 01/2003 0.26 kg
Bar code scanner Camera / scanner (imager)
5 Operation
5.1 Fitting the torque module 3
WARNING
Electrical hazards! Risk of short circuiting.
▶Before fitting the torque module, check to ensure that the terminals on the impact wrench and on
thetorquemodulearefreefromforeignobjects.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

4English
WARNING
Risk of injury! Hazard presented by a falling torque module.
▶Check that the torque module is securely attached to the impact wrench.
▶Push the torque module onto the impact wrench from the rear until it is heard to engage with a click.
5.2 Inserting the battery 4
WARNING
Electrical hazards! Risk of short circuiting.
▶Before inserting the battery, check to ensure that the battery terminals and the contacts on the
torque module are free from foreign objects.
WARNING
Risk of injury! Hazard presented by a falling battery.
▶Check that the battery is securely attached to the torque module.
▶Push the battery onto the torque module from the rear until it is heard to engage with a click.
5.3 Switching on and off
5.3.1 Switching on the torque module
Conditions
+ The torque module is switched off. Nothing is shown in the display.
1. Set the forward/reverse switch on the impact wrench to the “forward” position.
2. Press the control switch on the impact wrench briefly.
◁The display illumination switches on and shows the start screen briefly ( ).
◁The indicator LEDs light red for 1 second as a check and then green for 1 second.
◁The last previously selected operating mode is shown in the display in a selection frame.
▽An error/message is shown in the display.
▶Refer to the “Troubleshooting” section for information about the possible causes of error messages
and the steps to be taken to remedy the problem.
3. Press the lock button.
◁The torque module is now locked and the impact wrench is ready for use.
5.3.2 Switching off the adaptive torque module
The adaptive torque module switches itself off automatically:
• when the impact wrench switches off automatically after a long idle period
• whenthebatteryisremoved
• when the USB connection between the torque module and the PC is interrupted(oneoftheUSB
connectors is unplugged).
5.4 Basic operation
Note
In this section, the most frequently used basic functions are explained in order to illustrate how the
module is used.
A detailed description of certain operations can be found in the section covering specific applications.
Unlocking the module
In order to change the settings on the adaptive torque module, the module first has to be unlocked.
▶If you wish to unlock the adaptive torque module, press and hold the lock button for at least 3
seconds.
◁In the display a selection frame appears around the last previously shown type of fastening and the
last previously shown operating mode.
◁The torque module is unlocked and in setting mode. The impact wrench is deactivated.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 5
Navigation
When the selection frame and several elements (options, parameters) are shown in the display, the selection
frame can be moved by pressing the arrow buttons and .
Selecting options / changing parameters
When the torque module is unlocked, options or parameters can be adjusted as follows:
▶Position the selection frame in the display on the element (option / parameter) that you wish to change.
▶Press the OK button.
◁The element will be highlighted.
▶Use the arrow buttons to make the desired setting.
▶Press the OK button to accept the setting shown.
◁The element is again shown in the selection frame.
Locking the module
After all settings have been made, the adaptive torque module must be lockedagain.
▶Press the lock button .
◁The selection frame disappears from the display. The operating parameters that have been set are
now saved and cannot be changed accidentally.
◁The adaptive torque module is locked and the impact wrench activated again.
5.5 Basic settings
5.5.1 Displaying the basic settings menu
1. If the torque module is locked, unlock the torque module by pressing and holding the lock button for at
least 3 seconds.
2. Press the OK button and hold it in this position for at least 3 seconds.
◁The basic settings menu is shown.
5.5.2 Selecting functions from the basic settings menu
1. Use the arrow buttons to move the selection frame to the symbol for the desired function.
Functions in the basic settings menu
Symbol Function
Setthevolumeofthesignaltoneorswitchthetoneon/off
Set the brightness and contrast of the display
Show the date and time set in the torque module
Note
The clock can only be set using the PC software PROFIS Adaptive Torque.
Show the remaining time / period of use until servicing of the impact wrench is again
due
Show the amount of memory used in the torque module
Note
When the value indicated reaches 100%, the oldest data will be overwritten.
The PROFIS Adaptive Torque PC application can be used to read the recorded data
and to delete data from memory in the torque module.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

6English
Symbol Function
Show the software version installed in the torque module
Leave the basic settings menu
2. Press the OK button.
5.5.3 Setting the signal tone volume or display brightness and contrast
Note
The settings for volume, brightness and contrast are made in the same way. Accordingly, as an
example, only the setting of the brightness and contrast is described in the following paragraphs.
1. Press the right or the left arrow button to set the desired brightness / contrast level.
◁The number of black rectangles indicates the level selected (in the illustration above: level 3).
◁When level 0 is reached the symbol changes to indicate that the backlighting is switched off.
2. Press the OK button.
◁The basic settings menu is shown again.
5.5.4 Display showing maintenance status / remaining period of use
After activation of the symbol in the basic settings menu the remaining period of use of the impact
wrench until the next service is shown in the following display screens.
Note
Irrespective of what is shown in the display, the impact wrench must be serviced at least once a year
in order to ensure the quality of the bolt fastenings made with it.
Display showing maintenance status of the impact wrench
Indication in the display Meaning
The impact wrench is in good condition, no maintenance required
in the foreseeable future
Maintenance of the impact wrench is soon due
The segments in the rectangle in the display show the remaining
period of use.
Maintenance of the impact wrench must be carried out immedi-
ately.
The indication in the display appears automatically after the end of
the remaining period of use (warning).
The “Adaptive” and “Tightening” operating modes can no longer
be selected
5.5.5 Leaving the basic settings menu
1. Move the selection frame to the symbol.
2. Press the OK button.
◁The last previously shown operating mode will be displayed.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 7
5.6 Operating modes
5.6.1 Adaptive operation
Note
The following information applies only to forward rotation of the impact wrench (tightening). In reverse
rotation, the impact wrench runs at the highest torque setting.
In “Adaptive” operating mode, the adaptive torque module regulates the tightening of the selected type
of bolted connection. The tightening parameters from the most recently installed software update will be
applied. As the product designations and the tightening parameters may change, make sure that the latest
software version is installed in the torque module.
Note
When “Adaptive” operating mode is selected, the “AT” torque indicator lights in the display on the
impact wrench. The torque selector switch on the impact wrench is then inactive and the impact
wrench’s control switch simply has an ON/OFF function.
Parameters in adaptive operating mode
@Type of tightening operation (short name for
fastener)
;Material grade / quality
=Diameter
The illustration shows the positions of the operating parameters shown in the display.
Type of threaded fastener
Factory-set parameters for various types of threaded fastener have been saved in memory in the torque
module.
Note
The list below can vary from country to country, so the threaded fasteners listed should be considered
as examples only.
The parameter settings published for the fasteners can change; the softwareinthetorquemodule
must therefore be kept up to date at all times.
Indication in the display Meaning
HS… HS… stud anchor
Material grade / quality
Indication in the display Meaning
— (display stays blank) Galvanized steel
R Stainless steel
Diameter
The following diameters can be selected as standard:
•8mm
•10mm
•12mm
5.6.2 “Tightening” operating mode
Note
The following information applies only to forward rotation of the impact wrench (tightening). In reverse
rotation, the impact wrench runs at the highest torque setting.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

8English
In this operating mode a total of 30 torque settings are available. The setting to be selected for a particular
type of tightening application depends on the diameter of the threaded fastener and the specified torque.
The setting is determined graphically on the basis of these data.
For the “Tightening” operating mode, the display shows the following:
The number to the right of the threaded-fastener symbol shows the selected setting.
5.6.2.1 Determining the required setting for the “Bolting” operating mode5
1. Determine the specified torque and diameter for the bolted connection to be tightened.
Note
For the sake of clarity, examples are shown in the diagram; the arrows show the direction in which
it should be read.
2. Start at the required torque on the vertical axis of the applicable diagram and then move horizontally to
the right until you reach the line for the correct diameter.
3. Then move vertically downwards until you reach the horizontal axis and read the setting at this point.
Note
The curves in the diagram were determined under specific conditions. Since the conditions in
everyday use constantly vary, the values determined using the diagram shouldbeusedonlyasa
guide. The correct setting should therefore be determined as described below by comparison with
a conventional torque wrench.
4. Set the specified torque on a torque wrench and tighten a bolted connection using the torque wrench.
5. Mark the exact position of the bolt or nut relative to the base material.
6. Release the bolt or nut again.
7. First select a slightly lower setting on the torque module than the one indicated in the diagram.
Note
This should prevent damage to the bolted connection as a result of overtightening.
8. Now use the impact wrench to tighten the bolt or nut.
9. Check whether the bolt or nut was tightened to exactly the same extent as with the torque wrench.
Result 1 / 3
The bolt or nut was not adequately tightened
▶Release the bolt or nut and reset the torque module to the next higher setting.
▶Tighten the bolt or nut using the new setting and carry out this step of the test again.
Result 2 / 3
The bolt or nut was overtightened.
▶Release the bolt or nut and reset the torque module to the next lower setting.
▶Tighten the bolt or nut using the new setting and carry out this step of the test again.
Result 3 / 3
The bolt or nut was tightened to exactly the same extent as with the torque wrench
The correct setting for the bolt or nut has been determined.
5.6.3 “Unregulated” operating mode
Adaptive torque control is deactivated in this operating mode. The impact wrench then functions as though
the adaptive torque control module was not fitted to the tool. The adaptive torque module therefore does
not have to be removed for short periods of use without adaptive torque control.
In the “Unregulated” operating mode the display shows the following:
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 9
Note
In the “Unregulated” operating mode the “AT” torque display control LED does not light. The torque
can be set on the impact wrench.
5.7 Setting the operating mode
The operating mode can be set in 2 different ways to the desired type of screw/bolt fastening:
• By scanning the applicable bar code or QR code
• By manually adjusting the setting by way of the buttons on the torque module
Scanning the bar code or QR code
If a bar code or a QR code is available for the Hilti product to be tightened, the operating mode can be set
correctly for the product quickly and easily by scanning the code.
▶Set the operating mode by scanning a bar code or QR code. → page 9
Manual settings
IfnobarcodeorQRcodeisavailablefortheproducttobetightened,theoperating mode can be set by way
ofthebuttonsonthetorquemodule.
Note
The “Unregulated” operating mode can only be set manually.
▶Use the buttons to set the operating mode. → page 9
5.7.1 Setting the operating mode by way of the control panel buttons
1. Unlock the torque module. → page 4
2. Use the arrow buttons to move the selection frame, as necessary, onto another option that you wish to
change.
3. Press the OK button.
◁The selected option is then shown highlighted in black.
4. Use the arrow buttons to select the desired setting.
5. Press the OK button.
◁The selected setting is again shown in the selection frame.
6. If necessary, repeat the last 3 steps to make further settings.
7. Lock the torque module. → page 4
5.7.2 Setting the operating mode by scanning the bar code or QR code 6
1. Unlock the torque module. → page 4
2. Press the scan button.
◁The scanner is activated and readiness for scanning is indicated in the display by the symbol.
3. Now hold the module so that it faces the bar code or QR code at a distance of approx.. 15 centimeters
(6″), so that the code is within the frame projected by the scanner.
◁The indicator LEDs light green.
◁The confirmation tone is emitted (can be deactivated in the basic settings).
◁The operating mode for the product to be tightened is shown in the display.
▽The indicator LEDs light red.
▽The warning tone is emitted (can be deactivated in the basic settings).
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

10 English
▽is shown in the display (code could not be read or was not recognized).
▶Press the scan button and scan the code again.
Note
It is possible that operating parameters for the product to be tightened are not yet available
fromthetorquemodulememory.IfaQRcodemarkedwith"SIATready"existsfor the
product, please scan this code as this also contains the necessary tightening parameters
and the data scanned will then be saved in the torque module memory. The tightening
parameters for the product can also be uploaded via USB to the torque module by using
the PROFIS Adaptive Torque PC application. Regularly check for updates to the software
installed in the torque module in order to ensure that the latest parametersarealways
applied.
SIAT ready QR codes, if they exist for the product, can be found on the packaging, in the
instructions for use of the product or online in the download area for the applicable product
at the Hilti website.
4. Lock the torque module. → page 4
5.8 Tightening the bolted connection in “Adaptive” operating mode
Note
Before using the torque module, check to ensure that the product to be tightened is installed correctly.
Observe the information and instructions concerning checking bolted connections.
1. Set the tool to “Adaptive” operating mode.
2. Set the forward/reverse switch to the “forward” position.
3. Fit a suitable accessory tool (e.g. socket) to the impact wrench and then bring it into position on the
producttobetightened.
4. Press the control switch and hold it in this position until the torque moduleemitsoneofthefollowing
signal tones (Note: the tone generator may deactivated).
Result 1 / 4
• The symbol indicating “Bolting completed successfully” is displayed.
• The indicator LEDs light green.
• The confirmation tone is emitted.
The bolted connection has been tightened correctly. You may proceed with the next bolted connection
of the same type.
Result 2 / 4
• The symbol indicating “Bolting completed successfully” is displayed.
• The indicator LEDs blink green.
• The confirmation tone is emitted.
A bolted connection already tightened and subsequently released has now been retightened. The
operation was carried out in accordance with specially defined retightening parameters and has been
completed successfully.
Result 3 / 4
• The symbol indicating “Battery voltage too low” is displayed.
• The indicator LEDs light red.
The power remaining in the battery is inadequate for the next bolted connection.
▶Press the OK button to confirm the message.
▶Fit a charged battery.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 11
Result 4 / 4
• The symbol indicating “Bolting not completed correctly” is displayed.
• The indicator LEDs light red.
• The warning tone is emitted.
▶Use a suitable torque wrench to tighten the bolted connection.
▶Once you have tightened the bolted connection, confirm this by pressing theOKbutton.
5.9 Tightening the bolted connection in “Bolting” operating mode
1. Set the tool to the “Bolting” operating mode.
2. Determine the tightening setting for the bolted connection to be made → page 8 and set this accordingly.
3. Set the forward/reverse switch to the “Forward” position.
4. Fit a suitable accessory tool to the impact wrench and then bring it into position on the product to be
tightened.
5. Press the control switch and hold it in this position until the torque moduleemitsoneofthefollowing
signal tones (Note: the tone generator may deactivated).
Result 1 / 2
• The symbol indicating “Bolting completed successfully” is displayed.
• The indicator LEDs light green.
• The confirmation tone is emitted.
The bolted connection has been tightened correctly. You may proceed with the next bolted connection
ofthesametype.
Result 2 / 2
• The symbol indicating “Bolting not completed correctly” is displayed.
• The indicator LEDs light red.
• The warning tone is emitted.
▶Use a suitable torque wrench to tighten the bolted connection.
▶Once you have completed the operation, confirm this by pressing the OK button.
5.10 Checking threaded fastener
5.10.1 Checking the security of stud anchors
Note
To ensure that the specified installation torque as per the approval / operating instructions has been
correctly applied when the "Adaptive" operating mode is used to tighten stud anchors, the first anchor
and the last anchor have to be checked with a suitable, calibrated torque wrench. This check of the
applied installation torque has to be carried out immediately after tightening (installation) of the stud
anchor.
▶Use a suitable, calibrated torque wrench to check the tightening torque applied to the fastening element.
In this process, observe the angle through which the fastening element can be turned in the tightening
direction.
Angle-of-rotation guide values for checking tightening torque
Anchor diameter (Ø) Maximum angle of rotation
(α)
≤M10 90°
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

12 English
Anchor diameter (Ø) Maximum angle of rotation
(α)
≥ M12 180°
Result 1 / 2
The fastening element was not turned further than through the specified maximum angle of rotation (α).
Installation of the threaded fastener undertaken in the "Adaptive" operating mode was performed
correctly; the specified installation torque was achieved.
Result 2 / 2
The fastening element was turned further than the specified maximum angle of rotation (α).
Installation of the threaded fastener undertaken in the "Adaptive" operating mode is faulty, because the
specified installation torque was not achieved. The threaded fasteners tightened since the previous check
aretoberegardedasfaultyandmustbechecked.Theimpactwrenchmustbechecked by Hilti Service.
5.10.2 Checking bolted connections made using the “Bolting” operating mode
▶At regular intervals, use a suitable torque wrench in accordance with the manufacturer’s instructions or
specifications, to check that the nominal torque has been achieved.
5.11 Removing the battery
▶Remove the battery (→ SIW 6ATA22 operating instructions).
5.12 Removing the torque module 7
1. Remove the battery. → page 12
2. Press the release button on the torque module and hold it in this position.
3. Pull the torque module away from the impact wrench to the rear.
5.13 Connecting the torque module to a PC 8
1. Removethetorquemodule.→page12
2. Open the sliding cover on the underside of the torque module.
◁The USB socket is then accessible.
3. Plug the connector on the USB cable (type B, USB 2.0) into the USB socket on thetorquemodule.
4. Plug the other connector on the USB cable (type A) into the PC.
◁The PC then supplies power to the torque module. The USB logo isshowninthedisplayon
the module.
Note
Information about the functions available to you can be found in the instructions for use of the
PROFIS Adaptive Torque software.
Note
After unplugging the USB cable from the torque module you should close the cover over the USB
socket in order to protect it from dirt and dust.
6 Care and maintenance
Note
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with the product can be found at your
local Hilti Center or online at: www.hilti.com
▶Keep the product, especially its grip surfaces, clean and free from oil and grease. Do not use cleaning
agents containing silicone.
▶Clean the outer surfaces of the tool with a slightly damp cloth at regular intervals.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

English 13
7 Transport and storage
▶To avoid damage, use the supplied storage box or the toolbox when transporting or storing the adaptive
torque module.
8 Troubleshooting
If the problem you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
Note
Please also pay attention to the troubleshooting information provided in the operating instructions for
the impact wrench used..
Malfunction Possible cause Action to be taken
The symbol indicating “Lock
module” is displayed.
The torque module is unlocked. ▶Press the lock button in order
tolockthetorquemoduleand
activate the impact wrench.
The symbol indicating “Bat-
tery temperature too high” is
displayed.
The battery has overheated. ▶Change the battery or allow the
battery to cool down.
The symbol indicating “Bat-
tery temperature too low” is
displayed.
Battery temperature is too low. ▶Fitabatterythat’satatem-
perature within the permissible
battery operating tempera-
ture range (please refer to the
operating instructions for the
battery).
The symbol indicating “Im-
pact wrench temperature too
high” is displayed.
The impact wrench has
overheated.
▶Allow the impact wrench to cool
down and clean the air vents.
The symbol indicating “Low
battery” is displayed.
Battery charge is not sufficient
to tighten the bolted connection
correctly.
▶Fit a charged battery.
The symbol indicating “Elec-
tric current drawn is too high”
is displayed.
Current input is briefly too high. ▶Press the OK button to confirm
the message.
▶Repeat the tightening operation.
▶Contact Hilti Service if the
message reappears.
The symbol indicating “But-
ton cell empty” is displayed.
The battery (button cell) for the
clock in the torque module is dis-
charged.
Thecorrectnessofthedateand
time in the documentation report
can no longer be guaranteed.
▶Contact Hilti Service and have
the battery changed.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01

14 English
Malfunction Possible cause Action to be taken
The symbol indicating “Hard-
ware fault” is displayed.
A hardware fault has been identi-
fied.
▶Connect the torque module to a
PC.
▶Use the
PROFIS Adaptive Torque
software to read out fault
memory and follow the
software's troubleshooting
instructions.
The symbol indicating “Doc-
umentation function deacti-
vated” is displayed.
Documentation function deacti-
vated (warning only).
▶If you require the documen-
tation function, connect the
torque module to the PC and
activate the documentation
function in the PC software
PROFIS Adaptive Torque.
▶Whereapplicable,presstheOK
button to hide the message and
continue the starting process
for the torque module.
The symbol indicating “...%
of memory is in use” is dis-
played. (The symbol appears
when the value is ≥ 90 %.)
Usage of data memory in the mod-
ule is indicated in percent. Note:
When 100 % is reached, the oldest
data will be overwritten!
▶Connect the torque module to a
PC.
▶Use the
PROFIS Adaptive Torque
software to read out the data so
that they can be documented in
areport.
▶Subsequently delete the data in
thetorquemoduledatamemory
in order to clear the memory for
further use.
9 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
▶Disposal of electric tools or appliances together with household waste is not permissible.
10 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about the warranty conditions.
11 Declaration of conformity
We declare, on our sole responsibility, that this product complies with the applicable directives and standards.
It has been tested and approved for use together with the specified products.
Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 00Printed: 07.09.2017 | Doc-Nr: PUB / 5331629 / 000 / 01