Hirschmann MACH 1020 User manual

MACH 1000
Release 02 10/10
Technical Support
[email protected]
User Manual
Installation
Industrial ETHERNET Ruggedized Switch
MACH 1000 Family
MACH 1020
LS DA
USB V.24
MACH 1020
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
MACH 1030
LS DA
USB V.24
MACH 1030
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
22
MACH 1132
34
56
LS DA LS DA
LS DA
MACH 1032
USB V.24
PStandByRM
FAULT
R1 R2
2
1
PStandByRM
FAULT
R1 R2 ETHERNET Service Port
1357911 13 15 17 19 21 23
246810 12 14 16 18 20 22 24
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
USB V.24
PStandByRM
FAULT
R1 R2

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2010 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.beldensolutions.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
MACH 1000 039 687-002-02-1010 14.10.10

MACH 1000
Release 02 10/10 3
Contents
Safety instructions 4
About this Manual 10
Legend 10
1 Device description 11
1.1 Description of the device variants 12
1.2 Combination options 18
2 Assembly and start-up 21
2.1 Installing the device 21
2.1.1 Unpacking and checking 21
2.1.2 Installing the SFP modules (optional) 21
2.1.3 Connecting the power unit connections 
for supply voltage and signal contact 22
2.1.4 Installing the device and grounding 30
2.1.5 Startup procedure 34
2.1.6 Connecting the data lines 34
2.2 Display elements 38
2.3 Basic set-up 41
2.4 Disassembling the device 43
3 Technical data 44
A Further Support 53

4MACH 1000
Release 02 10/10
Safety instructions
This documentation contains instructions which must be observed to ensure
your own personal safety and to avoid damage to devices and machinery.
Certified usage
The device may only be employed for the purposes described in the
catalog and technical description, and only in conjunction with external
devices and components recommended or 
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced 
carefully.
Supply voltage
The supply voltage is electrically isolated from the housing.
Use undamaged parts.
The device does not contain any service components. Internal fuses
are only triggered if there is a fault in the device. If the device is not
functioning correctly, or if it is damaged, switch off the voltage supply
and return the device to the plant for inspection.
Only switch on the device when the housing is closed.
Connect the protective conductor before you set up the other
connections. When removing the connections, you remove the
protective conductor last.
Connect both protective conductors if your device is equipped with two
power supply units.
Make sure that the cross-section of the protective conductor cable is
the same size as or bigger than the cross-section of the voltage supply
cables.
Only use connection cables that are permitted for the specified
temperature range.
Warning: Never insert sharp objects (small screwdrivers, wires,
etc.) into the field connection terminals for the supply voltage,
and do not touch the terminals! There is the risk of an electric
shock.

MACH 1000
Release 02 10/10 5
Warning:
– If the neutral conductor or the negative terminal of the supply
voltage is not grounded
– If you are using a DC voltage greater than 125 VDC for the
supply voltage install a suitable input fuse.
For power supply units with product code “G” or “M”, use a slow-
blow fuse with a nominal rating of 2.5 A for the voltage supply
input.
For power supply units with product code “C” or “L”, use a slow-
blow fuse with a nominal rating of 6.3 A.
With AC power supply, use a cable cross-section of at least 0.75
mm² (North America: AWG 18) for the current conductor at the
voltage input.
With DC power supply, use a cable cross-section of at least 1.0
mm² (North America: AWG 16) for the current conductor at the
voltage input. 
Relevant for North America: For use in Class 2 circuits.
Only use copper wire/conductors of class 1, 60/75°C or 75°C.
Warning: Only connect a supply voltage that corresponds to
the type plate of your device.
Power unit type “C” and “L”: 18 to 60 V DC
Power unit type “G” and “M”: 77 to 300 V DC or 90 to 265 V AC
Shielding ground
The shielding ground of the connectable twisted pairs lines is connected
to the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Depending on the device variant, it is grounded
via a separate spring-loaded terminal. This is located at the 1 or 2
power supply module(s) on the back of the device.
via a ground connection on the front panel of the device.
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
The ventilation slots must not be covered so as to ensure free air
circulation.
The clearance to the ventilation slots of the housing must be at least
10 cm (3.94 in).
Do not touch the housing during operation or shortly after switching off
the device. Hot surfaces can cause injury.

6MACH 1000
Release 02 10/10
Warning!
Never insert sharp objects (small screwdrivers, wires, etc.) into
the inside of the product. There is the risk of an electric shock.
The device must be installed in the horizontal or upright position, either
in the switch cabinet or on the wall (see on page 30 “Installing the
device and grounding”) The device is not intended for operation as a
table unit.
Operating the device in the maximum surrounding air temperature and
stacking devices: When installing the device, make sure there is at
least one free rack space (approx. 5 cm) above the device, because
heat is discharged via the housing of the device.
If you are operating the device in a 19" switch cabinet: install sliding/
mounting rails for holding the device (see on page 30 “Installing the
device and grounding”).
Warning: Only install the device in rooms / plants that are only
accessible to trained maintenance personnel.
If installed in a living area or office environment, the device must be
operated exclusively in switch cabinets with fire protection
characteristics in accordance with EN 60950-1.
Warning: Never insert sharp objects (small screwdrivers, wires,
etc.) into the field connection terminals for the supply voltage,
and do not touch the terminals! There is the risk of an electric
shock.
Environment
The device may only be operated at the specified surrounding air
temperature (temperature of the surrounding air at a distance of up to 5
cm (1.97 in) from the device) and relative air humidity specified in the
technical data.
Install the device in a location where the climatic threshold values
specified in the technical data will be observed.
Use the device only in an environment within the contamination level
specified in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:

MACH 1000
Release 02 10/10 7
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply with every detail of
the safety requirements specified in the operating instructions regarding
the voltages to apply (see page 4).
Non-observance of these safety instructions can therefore cause material
damage and/or serious injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. These personnel must be thoroughly familiar with all the
warnings and maintenance procedures in accordance with this
operating manual.
The proper and safe operation of this device depends on proper
handling during transport, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the
corresponding product. This may limit their possible usage in the
overall system.
Note: LED or LASER components in compliance with IEC 60825-1
(2001):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

8MACH 1000
Release 02 10/10
Warning 
Laser light 
Do not look into the beam or view it directly with optical
instruments (e.g. magnifying glass, microscope). 
Failure to observe this warning within a distance of 100 mm can
endanger your sight.
Light is emitted from the optical connections or from the ends of
the optical fibers that are connected to them. Light Emitting
Diode CLASS 2M, wave length 650 nm, power <2 mW,
according to DIN EN 60825-1:2003-10. 
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The devices comply with the regulations contained in the following
European directive(s):
2004/108/EG
Directive of the European Parliament and the council for standardizing
the regulations of member states with regard to electromagnetic
compatibility.
2006/95/EG
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electrical equipment to be
used within specific voltage ranges.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2:2005
Emitted interference: EN 55022:2006 + A1:2007 Class A
Safety: EN 60950-1:2006

MACH 1000
Release 02 10/10 9
Warning!
This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to
take appropriate measures.
Warning!
The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
FCC note:
This device complies with part 15 of FCC rules. Operation is subject to the
following two conditions : (1) This device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can radiate same, and
if it is not installed and used in accordance with this operating manual, it
can cause radio transmission interference. The use of this device in a
living area can also cause interference, and in this case the user is
obliged to cover the costs of removing the interference.
Recycling note
After usage, this product must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your county,
state and country.

10 MACH 1000
Release 02 10/10
About this Manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD-ROM supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Web-based Interface reference guide
Command Line Interface user manual
The HiVision Network Management Software provides you with additional
options for smooth configuration and monitoring:
Event log
Configuration of “System Location” and “System Name”
Configuration of the network address range and the SNMP parameters
Saving the configuration on the device
Simultaneous configuration of multiple devices
Configuration of the port display color red for a connection error
With the Industrial HiVision Network Management software, you increase
your network security in industrial application areas:
ETHERNET Early Warning System
Easy monitoring of industrial networks
Fast display
Interface with diagnostic and configuration programs
Low deployment cost
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

MACH 1000
Release 02 10/10 11
1 Device description
The Ruggedized Switch for Substations and Transportation MACH 1000
Family provides you with a wide range of Switch variants. You set up your
own Switch according to your requirements regarding the number of ports,
transmission speed, media type, connector type, temperature range, voltage
range and software variant.
The MACH 1000 devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility. The devices work without a fan. If required,
the devices are PoE-capable. For devices without PoE, the voltage supply
can be redundant if required. The Switches are mounted in the switch cabinet
by means of brackets, or vertically on the wall.
The HIPER-Ring redundancy concept enables you to quickly carry out a
reconfiguration, and also a simple configuration with only one additional
connection. Diagnosis displays and the display of the operating parameters
provide a quick overview.
It can be easily managed via a Web browser, via Telnet, with a management
software product (such as HiVision) or locally on the switch (V.24 interface).
The device allows you to set up switched industrial ETHERNET networks
that conform to the IEEE 802.3 and 802.3u standards using copper wires or
optical fibers in a line or ring structure. You can connect terminal devices and
other infrastructure components via twisted pair cables, multi-mode F/O and
single-mode F/O. The twisted pair ports support 
autocrossing, autonegotiation and autopolarity.
Depending on the software you choose, the devices provide you with a large
range of functions:
Redundancy functions 
(Rapid Spanning Tree, Redundant Ring Structure, HIPER-Ring,
Redundant Coupling, Link Aggregation, for devices without PoE
Redundant Power Supply)
Protection from unauthorized access
Synchronized system time in the network
Network load control
Operation diagnosis
Diagnostics (hardware self-testing)
Reset
Priority
VLAN
Topology Discovery
Web-based Interface
Command Line Interface CLI

12 MACH 1000
Release 02 10/10
SNMP
802.1x port authentication
Real Time Clock (Professional software variant)
The addition, to the MACH 1000 Ruggedized Switch series, of the switches
of the Open Rail range, the MICE range, the backbone switches of the MACH
3000 and MACH 4000 ranges, the BAT wireless transmission system, the
EAGLE security system, and products for the LION control room, provides
continuous communication across all levels of the company.
1.1 Description of the device variants
The devices differ with regard to the range of software functions, the number
of interfaces, and the media type for connecting segments.
The MAR1020-..., MAR1022-..., MAR1120-... and MAR1122-... device
variants are MACH 1000 Ruggedized Switches without Gigabit ports and,
depending on the requirements, a selectable number (up to 24) of Fast
Ethernet ports (10/100 Mbit/s). You can choose the media for the Fast
Ethernet ports 1 to 24 in pairs.
The MAR1120-... and MAR1122-... devices have an additional Fast
Ethernet port on the front of the device that you can use for diagnosis
purposes.
The MAR1022-... devices support PoE in accordance with IEEE
802.3af. 
The PoE ports are the Fast Ethernet ports 1 to 4.
In the MAR1120-... devices, all the cable outlets are at the back, i.e.
the ports are on the back of the device.
The MAR1122-... devices support PoE in accordance with IEEE
802.3af. 
The PoE ports are the Fast Ethernet ports 1 to 4.
All the cable outlets are at the back, i.e. the ports are on the back of
the device.
The MAR1030-..., MAR1032-..., MAR1130-... and MAR1132-... device
variants are MACH 1000 Ruggedized Switches with 2 or 4 Gigabit ports
(10/100/1000 Mbit/s) and, depending on the requirements, a selectable
number (up to 24) of Fast Ethernet ports (10/100 Mbit/s). 
You can choose the media for the Fast Ethernet ports 1 to 24 in pairs.
In device variants with 2 Gigabit Ethernet ports, these ports are combo
ports (2 x SFP slot: 100/1000 Mbit/s, alternatively: 
2 x twisted pair RJ45 socket: 10/100/1000 Mbit/s). 
In device variants with 4 Gigabit Ethernet ports, these can be optionally -
SFP slots (2 x 2 slots), 

MACH 1000
Release 02 10/10 13
- twisted pair RJ45 sockets (2 x 2 sockets) or 
- 2 x SFP slots plus 2 x twisted pair RJ45 sockets.
The MAR1130-... and MAR1132-... devices have an additional Fast
Ethernet port on the front of the device that you can use for diagnosis
purposes.
The MAR1032-... devices support PoE (Power over Ethernet) in
accordance with IEEE 802.3af. The PoE ports are the Fast Ethernet
ports 1 to 4.
In the MAR1130-... devices, all the cable outlets are at the back, i.e.
the ports are on the back of the device.
The MAR1132-... devices support PoE (Power over Ethernet) in
accordance with IEEE 802.3af. The PoE ports are the Fast Ethernet
ports 1 to 4. 
In these devices, all the cable outlets are at the back, i.e. the ports are
on the back of the device.
The devices also provide you with the following options for selecting the
variant you desire:
Temperature range:
Standard 0 °C to +60 °C
Extended -40 °C to +85 °C
Extended -40 °C to +85 °C, conformal coating
Voltage range for power supply unit 1 and the optional power supply
unit 2:
18 VDC to 60 VDC
77 VDC to 300 VDC or 90 VAC to 265 VAC
The voltage supply connection can be a terminal or plugged connection,
as desired.
In devices with PoE, power supply unit 2 is the PoE power supply unit.
You can choose the connections to power supply unit 1.
Software variant: Professional
The devices comply with the specifications of the ISO/IEC standards 
8802-3u 100BASE-TX/-1000BASE-T, 
8802-3 100BASE-FX and 
8802-3 1000BASE-SX/LX.

14 MACH 1000
Release 02 10/10
Front view of the MACH 1000 with 2 Gigabit ports
Figure 1: 1 - LED display elements 
2 - USB interface 
3 - V.24 connection for external management 
4 - See following table, column 1 
5 - See following table, column 2
Front view of the MACH 1000 with 4 Gigabit ports (SFP)
Figure 2: 1 - LED display elements 
2 - USB interface 
3 - V.24 connection for external management 
4 - See following table, column 1 
5 - See following table, column 2
Gigabit ETHERNET
GE ports 1 and 2 (combo ports)
Fast ETHERNET
FE ports 1 to 24, free choice of connections
100/1000 Mbit/s
Fiber optic, SFP slots
Alternative connections:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA
MACH 1000
1256910 13 14 17 18 21 22
347811 12 15 16 19 20 23 24
1
2
12 453
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
MACH 1000
1256910 13 14 17 18 21 22
347811 12 15 16 19 20 23 24
1
2
3
4
USB V.24
PStandByRM
FAULT
R1 R2
12 453

MACH 1000
Release 02 10/10 15
Front view of the MACH 1000 with 4 Gigabit ports 
(2 x SFP and 2 x RJ45)
Figure 3: 1 - LED display elements 
2 - USB interface 
3 - V.24 connection for external management 
4 - See following table, column 1 
5 - See following table, column 2
Gigabit ETHERNET
GE ports 1 to 4
Fast ETHERNET
FE ports 1 to 24, free choice of connections
1000 Mbit/s
Fiber optic, SFP slots
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
Gigabit ETHERNET
GE ports 1 to 4
Fast ETHERNET
FE ports 1 to 24, free choice of connections
1000 Mbit/s
Fiber optic, SFP slots
And / or:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
MACH 1000
1256910 13 14 17 18 21 22
347811 12 15 16 19 20 23 24
1
2
3
4
USB V.24
PStandByRM
FAULT
R1 R2
2
12 453

16 MACH 1000
Release 02 10/10
Front view of the MACH 1000 with PoE
Figure 4: 1 - LED display elements 
2 - USB interface 
3 - V.24 connection for external management 
4 - See below table 1, column 1 
5 - See below table 1, column 2 
6 - See below table 2
Gigabit ETHERNET
Up to 4 GE ports
Fast ETHERNET
FE ports 1 to 4, Power over Ethernet
1000 Mbit/s
Fiber optic, SFP slots
And / or:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
TT:
RR:
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
Table 1: Gigabit ETHERNET, Fast ETHERNET FE ports 1 to 4
Fast ETHERNET
FE ports 5 to 24, free choice of connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
Table 2: Fast ETHERNET, FE ports 5 to 24
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA
MACH 1000
1256910 13 14 17 18 21 22
7811 12 15 16 19 20 23 24
1
234
LS DA LS DA
USB V.24
PStandByRM
FAULT
R1 R2
2
12 456
3
P
Power over
ETHERNET

MACH 1000
Release 02 10/10 17
Views of the MACH 1000, ports in the back
Figure 5: Front panel: 
1 - LED display elements 
2 - Diagnosis port
Figure 6: Rear panel:

1 - LED display elements 
2 - USB interface 
3 - V.24 connection for external management 
4 - See following table, column 1 
5 - See following table, column 2
The device variants of the MACH 1000 with ports on the rear panel 
have the following characteristics:
The display LEDs are on the front of the device. There are up to 4
LEDs for displaying the status of the Gigabit Ethernet ports and up to
21 LEDs for displaying the status of the Fast Ethernet ports, as well as
6 LEDs for displaying the device status.
The supply voltage connection and the ports are on the back of the
device. The device allows you to connect a maximum of 20 Fast
Ethernet ports as well as an additional Fast Ethernet port on the front
of the device that you can use for diagnosis purposes.
Gigabit ETHERNET
Up to 4 GE ports
Fast ETHERNET
FE ports 1 to 20, free choice of connections
1000 Mbit/s
Fiber optic, SFP slots
And / or:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
PStandByRM
FAULT
R1 R2 ETHERNETService Port
1357911 13 15 17 19 21 23
246810 12 14 16 18 20 22 24
MACH 1000
12
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
22
34
56
LS DA LS DA
LS DA
USB V.24
PStandByRM
FAULT
R1 R2
2
1
MACH 1000
1256910 13 14 17 18 21
347811 12 15 16 19 20 23 24
1
2
12 453
-/N +/L

18 MACH 1000
Release 02 10/10
1.2 Combination options
The product designation of your device is made from combining the desired
product characteristics in accordance with the following table. The
corresponding short designation is in column 3.
Item Characteristic Ident. Property
1 to 7 Product MAR1020
MAR1030
MAR1022
MAR1032
MAR1120
MAR1130
MAR1122
MAR1132
MACH Ruggedized Fast Ethernet Switch
MACH Ruggedized Gigabit Ethernet Switch
MACH Ruggedized Fast Ethernet Switch
with PoE ab
MACH Ruggedized Gigabit Ethernet Switch
with PoE ab
MACH Ruggedized Fast Ethernet Switch,
ports on the back
MACH Ruggedized Gigabit Ethernet Switch,
ports on the back
MACH Ruggedized Fast Ethernet Switch,
ports on the back and with PoE ab
MACH Ruggedized Gigabit Ethernet Switch,
ports on the back and with PoE ab
8 - (hyphen) -
9 to 10 10/100/1000 Mbit/s ports 
1+2 or 1 to 4
99
CC
4O
4T
OT
Not present (in MAR1020)
2 * combo port (SFP slot: 100/1000 Mbit/s,
alternatively twisted pair RJ45 socket: 10/
100/1000 Mbit/s)
2*2 ports Gigabit Ethernet SFP, 1000 Mbit/s
2*2 ports Gigabit Ethernet RJ45 
10/100/1000 Mbit/s
2 ports Gigabit Ethernet SFP 1000 Mbit/s
plus 2 ports Gigabit Ethernet RJ45 
10/100/1000 Mbit/s
11 to 12 10/100 Mbit/s ports 1+2 a) 99
TT
MM
JJ
NN
VV
UU
LL
GG
ZZ
RR
FF b
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC
100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km
100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
13 to 14 10/100 Mbit/s ports 3 + 4 See 11 to 12
15 to 16 10/100 Mbit/s ports 5 + 6 See 11 to 12
17 to 18 10/100 Mbit/s ports 7 + 8 See 11 to 12
19 to 20 10/100 Mbit/s ports 9 + 10 See 11 to 12
21 to 22 10/100 Mbit/s ports 11 + 12 See 11 to 12
Table 3: Combination options for the device variants of the MACH 1000

MACH 1000
Release 02 10/10 19
23 to 24 10/100 Mbit/s ports 13 + 14 See 11 to 12
25 to 26 10/100 Mbit/s ports 15 + 16 See 11 to 12
27 to 28 10/100 Mbit/s ports 17 + 18 See 11 to 12
29 to 30 10/100 Mbit/s ports 19 + 20 See 11 to 12
31 to 32 10/100 Mbit/s ports 21 + 22 See 11 to 12
33 to 34 10/100 Mbit/s ports 23 + 24 See 11 to 12
35 Temperature range S Standard 0 °C to +60 °C
U Extended -40 °C to +85 °C
F Extended -40 °C to +85 °C, conformal
coating
36 Voltage range 
power supply unit 1
C
G
L
M
18 VDC to 60 VDC terminal connection
77 VDC to 300 VDC or 90 VAC to 
265 VAC terminal connection
18 VDC to 60 VDC plugged connection
77 VDC to 300 VDC or 90 VAC to 
265 VAC plugged connection
37 Voltage range 
power supply unit 2 
or PoE power supply unit
9
C
G
L
M
Not present
18 VDC to 60 VDC terminal connection
77 VDC to 300 VDC or 90 VAC to 
265 VAC terminal connection
18 VDC to 60 VDC plugged connection
77 VDC to 300 VDC or 90 VAC to 
265 VAC plugged connection
38 Certifications H
T
CE, UL 508, GL, IEC 61850, IEEE 1613
Substation, EN 50121-4 Railway (along
track)
CE, UL 508, EN 50121-4 Railway (along
track), EN 50155 Railway (train) c
39 Software variant P Professional
a. In device variants with PoE (Power over Ethernet), the first four ports can be twisted pair TX
RJ45 10/100 Mbit/s (short designation TT) or twisted pair TX M12 10/100 Mbit/s (short
designation RR), as desired. The remaining ports can be selected freely from the table.
Power supply unit 2 is a PoE power supply unit (incoming voltage range, item 37: “G” or “M”).
You can choose the connections to power supply unit 1.
b. Devices with PoE or with FL ports: No „T“ certification (EN 50155 Railway (train)) available.
c. Nominal voltage on power supply type G and M: 110 VDC; on power supply type C and L:
36 VDC.
Item Characteristic Ident. Property
Table 3: Combination options for the device variants of the MACH 1000

20 MACH 1000
Release 02 10/10
Example of MACH 1000 product designation
MAR1030-
MACH Ruggedized Switch with Gigabit ports
CC
2 * combo port (SFP slot: 100/1000 Mbit/s, alternatively twisted pair RJ45 socket: 10/100/
1000 Mbit/s)
TT
10/100 Mbit/s ports 1 + 2: 2 * twisted pair TX, RJ45, 10/100 Mbit/s
MM
10/100 Mbit/s ports 3 + 4: 2 * Multimode FX DSC 100 Mbit/s
JJ
10/100 Mbit/s ports 5 + 6: 2 * Multimode FX MTRJ 100 Mbit/s
NN
10/100 Mbit/s ports 7 + 8: 2 * Multimode FX ST 100 Mbit/s
VV
10/100 Mbit/s ports 9 + 10: 2 * Singlemode FX DSC 100 Mbit/s
UU
10/100 Mbit/s ports 11 + 12: 2 * Singlemode FX ST 100 Mbit/s
LL
10/100 Mbit/s ports 13 + 14: 2 * Singlemode Long Haul FX DSC 100 Mbit/s
GG
10/100 Mbit/s ports 15 + 16: 2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
ZZ
10/100 Mbit/s ports 17 + 18: 2 * SFP slot 100 Mbit/s
TT
10/100 Mbit/s ports 19 + 20: 2 * twisted pair TX, RJ45, 10/100 Mbit/s
99
10/100 Mbit/s ports 21 + 22: Module position empty
99
10/100 Mbit/s ports 23 + 24: Module position empty
F
Temperature range extended: -40 °C to +85 °C, conformal coating
C
Voltage range, power supply
unit 1:
18 VDC to 60 VDC
G
Voltage range, power supply
unit 2:
77 VDC to 300 VDC or 90 VAC to 265 VAC
H
Certifications: CE, UL 508, GL, IEC 61850, IEEE 1613 Substation, EN
50121-4 Railway (along track)
P
Software variant: Professional
Table 4: Example of the product designation of a MACH 1000 with 2 Gigabit ports: 
MACH 1030- CC TT MM JJ NN VV UU LL GG ZZ TT 99 99 F C G H P