Robustel EG5200 User manual

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 1/12
EG5200
Hardware Manual
Version: 1.0.0
Date: Jun. 27, 2023

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 2/12
Regulatory and Type Approval Information
Table 1: Toxic or Hazardous Substances or Elements with Defined Concentration Limits
Radio Specifications for Europe
RF technologies
2G, 3G, 4G, GNSS, Wi-Fi*, BLE*
Cellular
Frequency *
EU Band：
4G: LTE FDD: B1/B3/B7/B8/B20/B28/B32
LTE TDD: B34/B38/B40/B42/B43/B46
3G: WCDMA: B1/B8
2G: GSM: B3/B8
Non-EU Band：
4G: LTE FDD: B2/B4/B5/B12/B13/B18/B19
/B25/B26
LTE TDD: B39/B41
3G: WCDMA: B2/B4/B5/B6/B19
2G: GSM: B2/B5
Wi-Fi Frequency
2.4 GHz: 2.412 ~ 2.484 GHz
5 GHz: 5150-5250MHz, 5745-5825MHz
BLE Frequency
2400 ~ 2483.5MHz
GNSS*
GPS L1, Galileo E1, GLONASS G1, BDS B1I, SBAS L1: 1559MHz to 1610MHz BDS B2a, GPS L5,
Galileo E5a: 1164MHz to 1215MHz
Max RF power
33 dBm±2dB@GSM, 24 dBm+1/-3dB@WCDMA, 23 dBm±2dB@LTE, 19dBm@WiFi, 4
dBm@BLE
Name of
the Part
Hazardous Substances
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
(DEHP)
(BBP)
(DBP)
(DIBP)
Metal
parts
o
o
o
o
-
-
-
-
-
-
Circuit
modules
o
o
o
o
o
o
o
o
o
o
Cables
and cable
assemblie
s
o
o
o
o
o
o
o
o
o
o
Plastic
and
polymeric
parts
o
o
o
o
o
o
o
o
o
o
o:
Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is
below the limit requirement in RoHS2.0.
X:
Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this
part might exceed the limit requirement in RoHS2.0.
-:
Indicates that it does not contain the toxic or hazardous substance.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 3/12
*May vary on difference models.
Note: Operation of 5150 ~ 5250 MHz frequency range is restricted to indoor use only.
電波法の規定により 5GHz 帯は屋内使用に限ります。
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC& IC Radiation Exposure Statement
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your
body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 4/12
Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des
environnements non contrôlés. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre
l’antenne et votre corps.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.
Simplified EU Declaration of Conformity
We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou,
China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is
available at the following internet address:
www.robustel.com/certifications/
Safety Information
General
- The router generates radio frequency (RF) power. When using the router, care must be taken on safety issues
related to RF interference as well as regulations of RF equipment.
- Do not use your router in aircraft, hospitals, petrol stations or in places where using cellular products is prohibited.
- Be sure that the router will not be interfering with nearby equipment. For example: pacemakers or medical
equipment. The antenna of the router should be away from computers, office equipment, home appliance, etc.
- An external antenna must be connected to the router for proper operation. Only uses approved antenna with the
router. Please contact authorized distributor on finding an approved antenna.
RF Exposure
- This device meets the official requirements for exposure to radio waves. This device is designed and manufactured
not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies.
- The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF
exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable
limits.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open.
Router may be used at this time.
The symbol indicates that the product should not be mixed with general household waste but must be sent to
separate collection facilities for recovery and recycling.
The symbol indicates that the product meets the requirements of the applicable EU directives.
The symbol indicates that the product meets the requirements of the relevant UK legislation.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 5/12
Related download link
Find more product documents or tools at:
www.robustel.com/documentation/
Technical Support
Tel: [phone]
Email: [e-mail]
Web: www.robustel.com
Document History
Updates between document versions are cumulative. Therefore, the latest document version contains all updates
made to previous versions.
Date
Firmware Version
Document Version
Change Description
Jun. 27, 2023
2.1.0
1.0.0
Initial release.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 6/12
Overview
EG5200 is a new generation of industrial edge computing gateway, supporting global 4G/3G/2G networks for cellular
backhaul, with a fully-fledged Debian 11(bullseye) based operating system able to support thousands of existing or
new ARMv8 (Raspberry Pi compatible) based applications.
Package Checklist
Before commencing installation ensure your package has the following components:
Device
2PIN Terminal
Block with Lock
4PIN Terminal
Block
5PIN Terminal
Block
6PIN Terminal
Block
Mounting Kit
RCMS Card
Quick Start Guide
Card
Wi-Fi Antenna
(Optional)
Cellular Antenna
(Optional)
Power Supply
(Optional)
Note: The accessories could be different on specific order.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 7/12
Panel Layout
(May vary on different models, please refer to Table1)
Top View Front View Bottom View
Table1
Model
PN
Cellular Antenna Port
WIFI/BLE Antenna Port
GNSS Antenna Port
EG5200-A5ZAZ-NU
B120001
0
0
0
EG5200-A5CAZ-NU
B120002
0
2
0
EG5200-A5AAZ-4L-A06GL_EG25-G
B120004
2
0
1
EG5200-A5BAZ-4L-A06GL_EG25-G
B120006
2
2
1

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 8/12
Interface Descriptions
1. Serial Ports. Two software configurable serial ports, could be configured as RS232 or RS485 or RS422.
Name
RS232 Mode
RS485 Mode
RS422 Mode
RXD1 or RX1+
data receiving
data receiving positive
CTS1 or RX1-
clear to send
data receiving negative
A1/RTS1 or TX1+
request to send
RS485_A1
data sending positive
B1/TXD1 or TX1-
data sending
RS485_B1
data sending negative
GND
Ground
Ground
Ground
RXD2 or RX2+
data receiving
data receiving positive
CTS2 or RX2-
clear to send
data receiving negative
A2/RTS2 or TX2+
request to send
RS485_A2
data sending positive
B2/TXD2 or TX2-
data sending
RS485_B2
data sending negative
GND
Ground
Ground
Ground
2. Ethernet Ports. 5 Ethernet ports, both of them could be configured as WAN or LAN.
LED
Description
Activity
On, blinking
Transmitting data
Off
No activity
Link
Off
Link off
On
Link on
3. Reset Button.
Function
Operation
Reboot
Press and hold the RST button for 2~5 seconds under the operating status.
Restore to default
configuration
Press and hold the RST button for 5 ~10 seconds under the operating status.
The RUN
light flashes quickly, and then release the
RST button, and the device will restore to the default configuration.
Restore to factory
configuration
Once the operation of restoring the default configuration is performed twice
within one minute, the device will restore to the factory default settings.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 9/12
4. Digital Input and Relay Output. Two sets of digital inputs. Some applications for reference are as below:
Note: The external power supply DC voltage range is 5V~30V, 0.1A max.
Name
Type
Description
DI1+
Digital I/O
Digital Input positive
DI1-
Digital Input negative
DI2+
Digital Input positive
DI2-
Digital Input negative
NC1
Relay Output
Normally Closed
COM1
Common
NO1
Normally Open
NC2
Normally Closed
COM2
Common
NO2
Normally Open
5. LED Indicators.
LED
Description
RUN
On, solid
Gateway system is initializing
On, blinking
Gateway starts operating
Off
Gateway is powered off
MDM
Color
With 4G Module:
2G: Red,3G: Yellow,4G: Green
On, blinking
Link connection is working
Off
Link connection is not working
Green
Strong signal
Yellow
Medium signal
Red
Weak or no signal
VPN
On, solid
VPN connection is established
Off
VPN connection is not established
USR1/USR2
Defined by user

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 10/12
Hardware Installation
1. SIM Card Installation. Remove the SIM card cover to insert the SIM
cards into the device, then screw up the cover.
2. Antenna Installation. Rotate the antenna into the antenna connector accordingly.
Rubber Antenna Installation
3. Terminal Block Installation. Insert the 4 PIN,5PIN and 6PIN terminal blocks into the interfaces connector, then
can connect the devices or sensors to the gateway with wires via corresponding interfaces.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 11/12
4. Power Supply installation. Insert the power supply cord into the corresponding terminal block if needed, then
insert the terminal block into the power connector.
5. DIN Rail Mounting. Use 2 M3 screws to fix the DIN rail to the device,
then hang the DIN rail on the mounting bracket.
6. Wall Mounting. Use 4 M3 screws to fix the DIN rail to the device,
then hang the DIN rail on the mounting bracket.
7. Grounding the Device. Grounding will help to prevent the noise effect due to electromagnetic interference (EMI).
Connect the device to the site ground wire by the grounding screw before powering on.

Robustel EG5200 Hardware Manual
RT120_HM_EG5200 12/12
Login to the Device
1. Connect the gateway’s Ethernet port to a PC with
a standard Ethernet cable.
2. Before logging in, manually configure the PC with
a static IP address on the same subnet as the
gateway address, click and configure "Use the
following IP address".
3. To enter the gateway's web interface, type
http://192.168.0.1 into the URL field of your
Internet browser.
4. Use login information shown in the product label
when prompted for authentication.
5. After logging in, the home page of the web
interface is displayed, then you can view system
information and perform configuration on the
device.
6. The automatic APN selection is ON by default, if
need to specify your own APN, please go to the
menu Interface->Cellular->Advanced Cellular
Setting->General Settings to finish the specific
setting.
7. For more configuration details please refer to
RT104_SM_RobustOS Pro Software Manual.
(END)
Support: [e-mail]
Website: www.robustel.com
©2023 Guangzhou Robustel Co.,Ltd.
All rights reserved. Subject to change without notice.