Hirschmann Power MICE User manual

RM Web L3P
Release 4.1 03/08 Technical Support [email protected]
Reference Manual
Web-based Interface
Industrial ETHERNET (Gigabit) Switch
Power MICE, MACH 4000

Thenamingofcopyrightedtrademarksinthismanual,evenwhennotspeciallyindicated,should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2008 Hirschmann Automation and Control GmbH
Manualsandsoftwareare protectedbycopyright.Allrightsreserved.Thecopying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the en-
closed CD applies.
The performance features described here are binding only if they have been expressly guaran-
teed in the contract. This publication has been created by Hirschmann Automation and Control
GmbH according to the best of our knowledge. Hirschmann reserves the right to change the con-
tents of this manual without prior notice. Hirschmann can give no guarantee in respect of the
correctness or accuracy of the details in this publication.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Rel. 4.1-01-0308 – 15.4.08

Content
RM Web L3P
Release 4.1 03/08 3
Content
About this Manual 9
Key 11
1 Opening the Web-based Interface 13
2 Basic Settings 17
2.1 System 18
2.2 Network 22
2.3 Software 24
2.3.1 Update via file selection 24
2.3.2 tftp update 25
2.4 Port Configuration 26
2.5 Power over ETHERNET 29
2.6 Load/Save 31
2.6.1 Loading the configuration 32
2.6.2 Saving the configuration 32
2.6.3 URL 33
2.6.4 Deleting a configuration 33
2.6.5 Using the AutoConfiguration Adapter (ACA) 34
2.6.6 Canceling a configuration change 35
2.7 Restart 37
3 Security 39
3.1 Password / SNMP 40
3.2 SNMPv1/v2 Access Setting 42
3.3 Telnet/Web/SSH Access 45
3.3.1 Description of Telnet access 45
3.3.2 Description of Web access 46
3.3.3 Description of SSH access 46
3.4 Port Security 48

Content
4RM Web L3P
Release 4.1 03/08
3.5 802.1x port authentication 51
3.5.1 Preparing the device for the
802.1X port authentication 52
3.5.2 Configuration table 52
3.5.3 Statistics table 55
3.5.4 Radius server 57
4Time 59
4.1 Interaction of PTP and SNTP 60
4.2 SNTP configuration 61
4.3 PTP configuration 64
4.3.1 PTP Global 64
4.3.2 PTP port 66
5 Switching 69
5.1 Switching Global 70
5.2 Filters for MAC addresses 71
5.3 Rate Limiter 73
5.3.1 Rate Limiter settings 74
5.4 Multicasts 75
5.4.1 Global settings 77
5.4.2 IGMP Querier 77
5.4.3 IGMP settings 78
5.4.4 Unknown Multicasts 78
5.4.5 Known Multicasts 79
5.4.6 Settings per port (table) 79
5.5 VLAN 82
5.5.1 Setting up the VLAN 84
5.5.2 Displaying the VLAN configuration 88
5.5.3 Deleting VLAN settings 89
5.5.4 Example of a VLAN configuration 90

Content
RM Web L3P
Release 4.1 03/08 5
6 QoS/Priority 91
6.1 Global 92
6.2 Port configuration 94
6.2.1 Entering the port priority 95
6.2.2 Selecting the trust mode 96
6.2.3 Displaying the untrusted traffic class 97
6.2.4 Shaping rate 97
6.3 802.1D/p Mapping 98
6.4 IP DSCP mapping 100
6.5 Queue Management 102
6.5.1 Strict Priority 103
6.5.2 Weighted Fair Queuing 103
6.5.3 Maximum bandwidth 104
7 Routing 105
7.1 Global 106
7.2 Configuring Router Interfaces 107
7.2.1 Configuration 107
7.2.2 Configuring secondary addresses 109
7.3 ARP 110
7.3.1 Setting ARP parameters 111
7.3.2 ARP statistics display 112
7.3.3 ARP table display 112
7.3.4 Editing the ARP table 113
7.4 Router Discovery Configuration 114
7.5 RIP 115
7.5.1 Configuration 115
7.5.2 Route distribution 117
7.5.3 Statistics 118
7.6 Routing table 120
7.6.1 Current 120
7.6.2 Static 121
7.6.3 Preferences 122

Content
6RM Web L3P
Release 4.1 03/08
7.7 Tracking 124
7.7.1 Configuration 124
7.7.2 Applications 125
8 Redundancy 127
8.1 Link aggregation 128
8.1.1 Configuring the link aggregation 128
8.1.2 HIPER ring and link aggregation 131
8.2 HIPER-Ring 132
8.2.1 Configuring HIPER-Ring Version 1 133
8.2.2 Configuring HIPER-Ring Version 2 (MRP Draft) 138
8.3 Redundant coupling 142
8.3.1 Configuring the redundant coupling 142
8.4 Rapid Spanning Tree 163
8.4.1 Configuring the Rapid Spanning Tree 164
8.5 VRRP/HiVRRP 171
8.5.1 VRRP/HiVRRP configuration 171
8.5.2 HiVRRP domains 175
8.5.3 Statistics 177
8.5.4 Tracking 179
9 Diagnostics 181
9.1 Event log 182
9.2 Ports 183
9.2.1 Statistics table 183
9.2.2 Utilization 184
9.2.3 SFP modules 185
9.2.4 TP cable diagnosis 186
9.3 Topology Discovery 189
9.4 Port Mirroring 191
9.5 Device Status 193
9.6 Signal contact 195
9.6.1 Manual setting 195
9.6.2 Function monitoring 195
9.6.3 Device status 197
9.6.4 Configuring traps 197

Content
RM Web L3P
Release 4.1 03/08 7
9.7 Alarms (Traps) 198
9.8 Report 200
9.9 IP address conflict detection 201
9.10 Self-test 203
10 Advanced 205
10.1 DHCP Relay Agent 206
10.2 DHCP Server 208
10.3 Industry Protocols 211
10.3.1PROFINET IO 212
10.3.2EtherNet/IP 212
10.4 Command Line 213
A Technical Data 215
B Reader´s comments 217
C Index 219
D Further support 223

Content
8RM Web L3P
Release 4.1 03/08

About this Manual
RM Web L3P
Release 4.1 03/08 9
About this Manual
The "Web-based Interface" reference manual contains detailed information
on using the Web interface to operate the individual functions of the device.
The "Command Line Interface" reference manual contains detailed informa-
tion on using the Command Line Interface to operate the individual functions
of the device.
The “Installation” user manual contains a device description, safety instruc-
tions, a description of the display, and all the other information that you need
to install the device before you begin with the configuration of the device.
The “Basic Configuration” user manual contains all the information you need
to start operating the device. It takes you step by step from the first startup
operation through to the basic settings for operation in your environment.
The “Redundancy Configuration” user manual contains all the information
you need to select a suitable redundancy procedure and configure it.
The “Industry Protocols” user manual describes how the device is connected
by means of a communication protocol commonly used in the industry, such
as EtherNet/IP and PROFINET.
The “Routing Configuration” user manual contains all the information you
need to start operating the routing function. It takes you step by step from
a small router application through to the router configuration of a complex
network.
The manual enables you to configure your router by following the examples.

About this Manual
10 RM Web L3P
Release 4.1 03/08
The Network Management Software HiVision provides you with additional
options for smooth configuration and monitoring:
XEvent logbook.
XConfiguration of „System Location“ and „System Name“.
XConfiguration of the network address range and SNMP parameters.
XSaving the configuration on the device.
XSimultaneous configuration of multiple devices.
XConfiguration of the port display color red for a connection error.

Key
RM Web L3P
Release 4.1 03/08 11
Key
The designations used in this manual have the following meanings:
Symbols used:
XList
Work step
Subheading
Link Indicates a cross-reference with a stored link
Note: A note emphasizes an important fact or draws your
attention to a dependency.
Courier ASCII representation in user interface
Router with firewall
Switch with firewall
Router
Switch
Bridge
Hub

Key
12 RM Web L3P
Release 4.1 03/08
A random computer
Configuration Computer
Server
PLC -
Programmable logic
controller
I/O -
Robot

Opening the Web-based Interface
RM Web L3P
Release 4.1 03/08 13
1 Opening the Web-based Inter-
face
To open the Web-based interface, you will need a Web browser (a program
that can read hypertext), for example Mozilla Firefox version 1 or later, or
Microsoft Internet Explorer version 6 or later.
Note: The Web-based interface uses the “Java™ Runtime Environment Ver-
sion 1.4.2.x, 1.5.x or 6.x” plug-in. If it is not installed on your computer yet, it
will be installed automatically via the Internet when you start the Web-based
interface for the first time. This installation is very time-consuming.
For Windows users: cancel the installation. Install the plug-in from the
enclosed CD-ROM. To do this, you go to “Additional Software”, select Java
Runtime Environment and click on “Installation”.
Figure 1: Installing Java
Start your Web browser.
Make sure that you have activated JavaScript and Java in the security
settings of your browser.

Opening the Web-based Interface
14 RM Web L3P
Release 4.1 03/08
Establish the connection by entering the IP address of the device which
you want to administer via the Web-based management in the address
field of the Web browser. Enter the address in the following form:
http://xxx.xxx.xxx.xxx
The login window appears on the screen.
Figure 2: Login window
Select the desired language.
In the drop-down menu, you select
– user, to have read access, or
– admin, to have read and write access
to the device.
The password “public”, with which you have read access, appears in the
password field. If you wish to have write access to the device, then high-
light the contents of the password field and overwrite it with the password
“private” (default setting).
Click on OK.
The Web site of the device appears on the screen.

Opening the Web-based Interface
RM Web L3P
Release 4.1 03/08 15
Note: The changes you make in the dialogs are copied to the device when
you click on “Write”. Click on “Load” to update the display.
Note: You can block your access to the device by entering an incorrect con-
figuration.
Activating the function “Cancel configuration change” in the “Load/Save”
dialog enables you to return automatically to the last configuration after a set
time period has elapsed. This gives you back your access to the device.
Figure 3: Website of the device with speech-bubble help

Opening the Web-based Interface
16 RM Web L3P
Release 4.1 03/08
The menu section displays the menu items. By placing the mouse pointer in
the menu section and clicking the right mouse button you can use “Back” to
return to a menu item you have already selected, or “Forward” to jump to a
menu item you have already selected.

Basic Settings
RM Web L3P
Release 4.1 03/08 17
2 Basic Settings
The basic settings menu contains the dialogs, displays and tables for basic
settings configuration:
XSystem
XNetwork
XSoftware
XPort configuration
XPower over Ethernet
XLoad/Save
XRestart

Basic Settings
18
2.1 System
RM Web L3P
Release 4.1 03/08
2.1 System
The "System submenu in the basic settings menu is structured as follows:
XDevice status
XSystem data
XDevice view
XReloading data
Figure 4: "System" submenu
Device status
This section of the website provides information on the device status and
the alarm state of the device.

Basic Settings
RM Web L3P
Release 4.1 03/08
2.1 System
19
Figure 5: Device status and alarm display
System data
This area of the website displays the system parameters of the device.
Here you can change,
– the system name,
– the location description,
– the name of the contact person for this device,
– the availability of the media modules (see fig. 6) and
– the temperature threshold values.
Name Meaning
Name System name of this device
Location Location of this device
Contact person Contact person for this device
Basic module Hardware version of the basic module
Media module 1 Hardware version of media module 1
Media module 2 Hardware version of media module 2
Media module 3 Hardware version of media module 3
Media module 4 Hardware version of media module 4
Media module 5 Hardware version of media module5
Media module 6 Hardware version of media module 6
Media module 7 Hardware version of media module 7
Power supply (P1/P2) Status of the power supply units
Operating time Time that has elapsed since the device was last restarted.
Temperature Temperature in the device. Lower/upper temperature thresh-
old values. If the temperature goes outside this range, the
device generates an alarm message.
Table 1: System data
Time of the oldest existing alarm
Cause of the oldest existing alarm
Symbol indicates the Device Status

Basic Settings
20
2.1 System
RM Web L3P
Release 4.1 03/08
Figure 6: Availability of the media modules
Device view
The device view shows the device with the current configuration. The
symbols underneath the device view represent the status of the individual
ports.
Figure 7:
Module present
Empty slot
Module was removed.
Click this check mark
to define this slot as an
empty slot.