Hisense XQG70-HR1014 User manual

Hisense & Whirlpool
Customer Service Manual
XQG70-HR1014
Content
1 Safety Items
2 Specification
3 Control Panel
4 Washer Characteristics
5 Install Introduce
6 Structure Perspective
7 Breakdown Maintenance Index
8 Main Part Parameter
9 Timer Wire Diagram
XQG70-HR1014S

Version 1
Customer Service
1. Safety Items
1.1 Please don’t use illegal spare parts
the spare parts of our washer have been special design and strict
test ,the function reach national and corporation criterion, and the machine
can safe、good work, in process of maintenance, if you want replace the
component part, please firstly choose the part that our company
supply ,and then change it .if you don’t ,the some wrong happened ,the
company will not be responsible for it.
1.2 Machine must be safe ground connection
(1) Before install and maintenance ,must be make sure good ground
connection in customer home, if no, it can make more serious static
phenomenon ,the customer will be scared or hurted,please make sure
warn customer and solve it himself
(2) Please don’t use transformer, universal plug、power socket and so on，
prevent damage machine and hurt customer himself and customer’s
belongings because of too large power
(3) Such as the plug and the socket do not match, the customer change the
power socket ,anybody can not change the plug of machine
1.3 using attention and maintenance safe
(1) before clearing and maintenance, must be cut off power supply
(2) after machine using or adjust done, should be close water source and
unplugged the power cord

Version 1
Customer Service
(3) when machine using, please fellow the basic safe rules
a. please don’t touch or operate washer when your hand humid or
barefoot
b. unplugged the power cord, please do not pull it
c. the washer not insolate, also not be wet water
d. please don’t operate washer when nobody take care of the children
e. before wash, must be clear the stuff at the pocket, like as coins、paper、
pen and so on
f. when washer spin, don’t open the cover
g. please protect control panel, don’t use sharp objects to scratch,
otherwise may lead to water infiltration, and may be leakage

Version 1
Customer Service
2. Specification
Parameter \ SKU XQG70-HR1014 XQG70-HR1014S
The biggest spin speed 1000rpm
The largest wash volume 7.0kg
Temperature range 95°
appearance of color White/Silver
size 600x440x850
Net weight 66KG
Voltage 220-240V
Frequency 50Hz
Fuse 14A
Heater Power 1900W
Power cord length 120cm
Drum volume 46L
Door diameter 320mm
Door open angle 172°

Version 1
3. Control panel

Version 1
4.
4.1 Panel function button
Prewashoak
Add the powder detergent or the powder degerming agent in the prewash
chamber.
Recommended for laundry which is heavily soiled or which should be
degermed, the duration can be chose to be 28 minutes , 38 minutes or 48 minutes.
During the 18 minutes from the beginning, the drum is turning, then it will stop and
the laundry is soaked. In the end, the water in the tub is drained off.
Temp.
On selecting a programme, a predefined temperature is displayed. Press
“Temp.” to set another temperature.
Extra Rinse
An extra rinse is added for each press of the button. Up to 3 rinses can be
selected, to prolong the rinse cycle.
The times of rinses can be displayed.
This option is particularly suitable for areas with very soft water or for
washing baby linen, and helps with allergies.
Wash Time
Wash time can be changed when press this button, accroding with different
programme, the range of -90~10 minutes is max.
Spin Time

Version 1
Customer Service
Rinse hold
Delay
Select programme , temperature and options.
This function is only suitable for spin programme.
For the Spin Programme,pressing the button to select any one kind of time
such as 5 minutes, 8 minutes, 10 minutes, 14 minutes.
Spin Speed
Every programme has a predefined spin speed .
Press the button to set another spin speed.
If spin speed “0”se lected, the final spinning is cancelled, and the
is drained out only. However,intermediate spin phases remin during water
rinse.
without progressing to the final spin cycle, to avoid creasing and prevent colours
If you selected “Rinse hold”,the laundry remains in the last rinse water
from changing.
To terminate the “Rinse Hold” by draining the water, without any
spinning, press the “Start /Pause” button.
To terminate the “Rinse Hold” by spinning the laundry, press the “Spin”
button to select the desired spin speed and then “Start /Pause” to start the spin
cycle.
The delay allows to run the machine at the consumer’s convenience, for
example at night when electricity is cheaper.

Version 1
Customer Service
The time delay indication disappears when the remaining programme time
Press the “Start Delay ”button to select the delay time by 1 to 23 hours.
Press the “start/pause”button. indication next to the “Start Delay”
button lights up and countdown of the delay time begins.
To cancel the “Delay”
Once having pressed the “start/pause”button, the number of hours preselected
can be reduced by pressing again the “Delay”button.
starts and it is replaced by the remaining programme time.
Before you press the “Start/Pause”button:
After having pressed the “Start/Pause”button:
Turn the programme selector to another position or press the “Reset”button.
from the time display.
Press the reset button for at least 3 seconds the start delay time disappears
Programme start
Open the tap and press the “start/pause”button,the indication lamp next
to the “start/pause”button light up .the programme sequence indicator shows
the current programme phase, running from left to right through wash、rinse、
spin/drain.
The time display show the remaining programme time.
Programme end
All the lights of the programme sequence indicator are off, and the “Door
Open”indication lights up.

Version 1
Customer Service
After every 50whole cycles, the indication light“ ”light up until the user
select“Drum Clear”programme to clean the drum.
Reset a running programme before the end
The “Reset”button cancels a programme before the end.
Any existing water is drained out before the door can be opened.
Form clear
Press the “Form Clear”button before the prohgramme start,when the last
rinse ,the machine can adjust the level and the strength of the water to clear the foam
remain.
Suggest drum clean
Turn the programme selector to the “Off”position.
Close the water tap.
Open the door and unload the machine.
Leave the door open to allow the drum to dry.
Change programme and/or options after programme start
Press the “Start/Pause”button to pause the programme.
Select the new programme (with temperature),any options and another spin
speed if you want.
Press the “Start/Pause”button again. The new programme continues at the
same position where the previous programme was interrupted.Do not add detergent
for this programme.
Press the “Reset”button for at least 3 second.

Version 1
Customer Service
Turn off the end sound
Press the “Extra Rinse”and“Delay”at the same time for at least 3 second,
the end sound can be truned off or truned on.
I.Program
When you have choosen the desires washing process but not yet press the
washing has its predefined process.When you want to reset a new process for each
washing program,the original one will be overwriten by then. Press process program
select knob when you want to have this funtion choose.Choose the relativeprocess.
“Start/Pause”button,you can press the “I.Program”button for 3 second.Each
Hold“I.Program”button for at least 3 seconds and press“Start/Pause”button to
recall the favourite process.
“Door Open”indication
Before starting and after end of a programme, the lamp lights to show that
that the door can be opened, as long as the wash programme is running, the door
remains locked and must on no account be forced open. in case you have an urgent
need to open it during the running programme,refer to “cancel (reset) a running
programme before the end”.
Red indication
“Water tap closed”
The appliance has no or insufficient water supply, open the water tap; If the
indication still lights up, refer to the “troubleshooting guide”in the
“Clean pump”
Waste water is not pumped out, check whether the drain hose is kinked or the filter
must be cleaned; in the latter case refer to the instructions for use (“removing the filter”).
instructions for use.