HIT FITNESS HIT00707 User manual

HIT00707
USERE MANUAL- Tyr Multi-Gym

Precautions for use
1.Please read this instruction carefully before using and installing the product.
2.Please consult your doctor before use this product correctly. If you have abnormal
discomfort such as dizziness, chest tightness, physical discomfort and abnormal pain
during exercise, please stop using it immediately.
immediately. This product should be used carefully for the old and the weak with
hypertension,diabetes,heart disease and other diseases. Do not use this product if
you suffer from otitis media,spondylitis or pleurisy (but not limited).
3. This product and all its parts may contain parts that can cause suffocation.
Please keep this product and all its parts out of the reach of children.
4. The product must be inspected before use. Do not use the product if there is any
damage or missing parts.
5. This product is for home use only and should not be used for commercial purposes.
6. When using this product, keep fingers, loose clothes and hair away from moving parts.
Long hair must be tied up and all accessories likejewelry shall be taken off.
7.Please use this product properly within your own physical capacity. Please do not
overuse
8. Please use this product on an absolutely smooth ground with no obstacles. It is
strictly forbidden to use it on slopes or slippery floors.
9. Please do not exercise within 40 minutes after a meal.
10. Please ensure that the distance between the equipment and the obstacles is not less
than 40 inches.
11. Minors should use this equipment under the supervision of an adult and strictly follow
the instructions for use.
12.Only with proper equipment installation, maintenance and use can achieve safe and
effective training. Users must be familiar with all warnings and precautions of the
equipment.
Storage and maintenance
1
1.Store the product in a cool place. Do not expose it to the
sun for a long time.
3. Do not place heavy objects on the product.

Step 1:
①Foot tubes (1 pair)
②Main frame+handle (2
pairs)
③Upper arms (1 pair)
④Elbow cushions
(1 pair)+ Elbow
cushion screws
⑤Bottom foot sleeves
(2 pairs)
⑥Foot tube connect
pipes (front and rear)
⑦Horizontal bar
⑧Connect pipes of
the main frame (1pair)
⑨Back cushion
⑩Supporting tubes
①Sit-up bench
⑫ Feet rest tube ⒀Connecting pipe
rubber cotton pull rope（2pcs）
Kit
Accessories
Extemal hexagon screws
a.M8x90mm(4 pcs)
Carriage Bolts
b.M8×65mm(16 pcs)
Extemal hexagon screws
c.M8x45mm(4 pcs)
Plastic handle screws
d.M8x40(2pcs)
Extemal hexagon screws
e.M8x12mm(2 pcs)
Plastic handle nuts
f.M8x12mm(2 pcs)
g. Fix plates (2 pcs)
h. Half round head
screws M6*60mm (4 pcs)
Extemal six angle wrenches
(2pcs)
i.Cross screwdriver (1pcs)
Extemal hexagon screws
j.M8x55mm(2 pcs)
k.Bolt
8mmx66mm(3pcs)
l. Extemal hexagon
screws M8*55mm (1 pcs)
n. Carriage Bolts M10*80mm + Plastic screw nut (1 set)
m. outer hexagon screws
M8x75mm (4 pcs)
O.Half round head
screws M8*30mm (4 pcs)
2

Step
2:
Install
4
foot
①Put foot tubes into the 4 bottom foot sleeves respectively (4 foot set parallel to the ground)
.
Step
3:
Mount
the
foot
tube
connecting
pipes
to
connect
left
and
right
main
frame
①Fasten the connect rods with the 8pcs
Step
4:
Install
the
main
frame
①Fix the bottom of the main frame and supporting tubes with the 8pcs Carriage Bolts
(b.M8X65mm).
② Attach the main frame tubes with the curved fix plates and fasten it with the （a.M8x90mm）
external
3
Carriage Bolts(b.M8×65mm).
As shown in the picture

Step
5:
Install
the
top
connecting
rod
① Use the external hexagon (c.M8x45mm) screws to pass out from the inside, put the fixed plate
on, and fasten it with the nuts of M8.
Step
6
:
Install
the
elbow
cu
shion
Tighten the plates with the built-in screws (h. Half round head screws M6*60mm)of elbow
cushions. And tighten the L shape handle too with screws (O.Half round head screws M8*30mm (4 pcs)).
4

Step
7
:
Install
back
cushion
① Fasten the holes on the two ends of the back cushion to the aligned nails on the
main frame with the external hexagon screws (e.M8x12mm).
Step
8:
Install
upper
arms
and
bar
①Insert the upper arms into the top of the main frame directly, as shown in the figure.
②After inserting 2 upper arms, slide down to a height that is convenient for you to install the
horizontal bar at the top, as shown in the figure.
③ After installing the arms, put the horizontal bar on the upper arms, Align hole positions, insert
the two (a.M8 x 75mm) screws from the top,fasten it with the nuts.
5

Step
9:
Adjust
the
suitable
angle
and
height
① When adjusting the hole position to the suitable height, you can use the screw of the plastic
handle screws (d.M8x40) to pass through the main frame and lock with the upper arm.
Step
10:
Install
the
bench
①Put the sit-up bench part on the main frame connection and use m.M8*75mm outer hexagon screws
to fix it. Then insert the M8*66 bolts to a suitable hole which suites you. ( will bring
different
angels and positions using).
6

Install
the
①Rotate the M8*55mm outer hexagonal screw to fix the foot rest, adjust the foot rest to a suitable
position, and insert the 8*66 bolt.
②Insert carriage screw M10*80mm into the mounting hole as shown in the picture, and then use the
plastic cover of the M10 to rotate and secure.
7

Installation complete as shown
8