Hitachi PJ-TX100 Installation instructions

CONFIDENTIAL
LCD PROJECTOR
PRODUCT SPECIFICATIONS
MODEL PJ-TX100 (C11H)
PJ-TX100E for Europe
PJ-TX100W for Asia, Australia
PJ-TX100U for USA, Canada
VER.1.2
Approved by
Date
May 19, 2004
Hitachi, Ltd.
Digital Media Division
Jiro Kawasaki
Senior Engineer
Ver1.1=>Ver1.2
Add PJ-TX100U
1.4 Lamp 2000hrs =>1000hrs
1.11 Delete 1035i@60Hz
1.13 Keystone input signal WVGA=>720p
1.14 DDC1/2B=>DDC2B RGB/DVI
1.25 Power code W/E/U
1.17 Power consumption
2.3A/1.1A=>2.3A/1.3A
3.Image quality condition
•Gamma: Default #1
• Temp: Custom (offset 0, gain 0)
1.25 Language 8=>10
3.25 DOT DEFECT
10% => 5%(G),10%(R),20%(B) : zero defect
4.2 Delete : WVGA

PJ-TX100W/E/U ver 1.2
1
1.GENERAL
1.1 OPTICAL STRUCTURE 3 LCD panels, one projection lens, RGB shutter method
1.2 LCD PANEL 0.7inch, P-Si TFT panel x 3, Stripe pixel configuration
1280 dots x 720 lines x 3 panels
Drive method: TFT Active Matrix, with micro lens
1.3 LENS F1.7~2.4 (f=20.0 ~ 31.9mm)
Manual Zoom x 1.6
Manual Focus
1.4 LAMP UHB 150W @ Normal mode
Lifetime 1000 hours This means below.
More than 50 % of lamps will operate 1000 hours.
Less than 50 % of them will stop operation before 1000 hours
including lamp burst. More than 50% performance is typical @ 1000 hours.
(Internal timer to shut projector down sets 1000 hours.
Lamp power drop around 10% down @ Whisper mode.)
1.5 FOCUS DISTANCE 0.8m ~ 8.6m (Wide), 1.3m ~ 13.8ｍ(TELE)
1.6 DISTANCE TO SCREEN WIDTH RATIO (:1) 1.15 (WIDE), 2.35 (TELE) --- reference purpose only
1.7 DISPLAY SIZE 30 inches ~ 300 inches (60 inches (16:9) at 1.5m, wide)
1.8 LENS SHIFT Vertical 5：-1 ~1：-5, Horizontal 3：1 ~ 1：3
1.9 COLOR 16.7 million colors
1.10 RESOLUTION
Video 720 TV lines (@ overscan mode)
RGB 1280 dots x 720 lines
1.11 SIGNAL
Composite Video NTSC, NTSC4.43, PAL(-BGDHI), SECAM, PAL-M, PAL-N, PAL60
Component Video 525i(480i), 525p(480p), 625i(575i),
1125i(1080i@50/60,) 750p(720p@60)
R,G,B IBM Compatible VGA, SVGA/XGA/SXGA/ (compressed)
MAC13",MAC16"
fv; 56 ~ 120Hz, fh; 31.5 ~ 91kHz (See 4.2table for compatibility)
1.12 AUDIO
Speakers NONE
Input NONE
Output NONE

PJ-TX100W/E/U ver 1.2
2
1.13 ADDITIONAL FEATURES
Mirror Reverse Image
Up-side Down Image
Picture Freeze by RS-232C
Magnify 4 times by RS232C
My Memory
2-3 Pull Down for NTSC
Digital Gamma Correction
R/G/B Color Adjustment
ASPECT selection
For Video: 4:3/16:9/Wide/MOVIE-1/MOVIE-2
For RGB: 4:3/16:9
15 Languages OSD (English, French, German, Spanish, Italian, Norwegian, Dutch, Japanese,
Portuguese, Chinese, Korean, Swedish, Russian, Finnish, Polish)
Vertical Digital Keystone Correction: ±15degrees
(Note: Input signal is 720p@60, Zoom position is Wide max.)
1.14PLUG & PLAY DDC 2B(VESA) for RGB INPUT and DVI
1.15 INTERFACE CONNECTORS
(1) VIDEO INPUT
Composite Video RCA jack X 1
S-Video Mini-Din 4 pin X 1
Component Video RCA jack x 3
Audio NONE
(2) RGB Input
Analog RGB 15 pin D-Sub shrink x 1
Pin Assignments See Table below
Audio NONE
(3) RGB MONITOR OUTPUT
NONE
(4) Control 9 Pin D-Sub shrink x 1
RS-232C (Serial)
NO Mouse emulation
(5) Audio output NONE

PJ-TX100W/E/U ver 1.2
3
R.G.Bin(RGB)
15 Pin D-Sub Pin assignments
NO. RGB Component Video NO. RGB Component Video
1 Red Cr/Pr 9 N.C. PLUG DETECT
2 Green Y 10 GND GND
3 Blue Cb/Pb 11 N.C. ID3
4 N.C. ID1 12 SDA (DDC) NC
5 GND GND 13 H/CompositeSync NC
6 GND(Red) GND(Cr/Pr) 14 Vsync ID2
7 GND(Green) GND(Y) 15 SCL (DDC) NC
8 GND(Blue) GND(Cb/Pb)
Control (RS232C)
9 Pin D-sub Pin assignments
1
2 RD
3 TD
4
5 GND
6
7 RTS
8 CTS
9
DVI-D
PIN No. TIRMINAL PIN No. TIRMINAL
1 TMDS DATA 2−13 NC (TMDS DATA 3+)
2 TMDS DATA 2＋14 ＋5V POWER
3 GND(TMDS DATA 2/4SHIELD) 15 GND
4 NC (TMDS DATA 4−) 16 HOT PLUG
5 NC (TMDS DATA 4＋) 17 TMDS DATA 0−
6 DDC CLK 18
TMDS DATA 0＋
7 DDC DATA 19 GND(TMDS DATA 0/5 SHIELD)
8 ANALOG VSYNC 20
NC (TMDS DATA 5−)
9 TMDS DATA 1−21 NC (TMDS DATA 5＋)
10 TMDS DATA 1＋22 GND (TMDS CLK SHIELD)
11 GND (TMDS DATA 1/3 SHIELD) 23 TMDS CLK ＋
12 NC (TMDS DATA 3−) 24 TMDS CLK −
1.16 POWER SUPPLY AC90 ~ 132V / AC198 ~ 264V (50/60Hz), 3 Wire Grounded
1.17 POWER CONSUMPTION 100 ~ 120V/220 ~ 240V, 50/60Hz 2.4 /1.3A typ., Max. + 10%
100V, 50/60Hz, 220W typ., Max. + 10%
1.18 DIMENSIONS 340X110X280 mm, 13.4X4.3X11.0 inch.(WXHXD)
Excluding extrusions
1.19 WEIGHT 4.4 kg, 9.7lbs

PJ-TX100W/E/U ver 1.2
4
1.20 NOISE LEVEL
Whisper mode; 27 dB average (A-weighted) at 1 m from the unit at 23 °C (Target)
Normal mode; 30dB average (A-weighted) at 1 m from the unit at 23 °C (Target)
1.21 TEMPERATURES (at 35°C ambient)
SURFACE Metal 60 °C maximum except screws and terminals
SURFACE Plastic 65 °C maximum except around ventilation holes
EXHAUST AIR 83 °C maximum around ventilation holes
SCREWS AND TERMINALS 75 °C maximum

PJ-TX100W/E/U ver 1.2
5
1.22 CONTAMINATION
AIR Filtration at intake vent
Dust Protection to prevent visible dust collection all optical component
on or near the focal plane. (*)
*) At just focused position on image, dust is not clearly noticed and size is 16 pixels
maximum (4x4, 3x5, 2x8)
1.23 KENSINGTONSLOT
1.24 REGULATORY (AGENCY, SAFETY, EMI/RFI) APPROVALS
US/Canada UL 60950/C-UL
FCC Part15 subpart B class B
Europe CE approval
EN61000-3-2, EN61000-3-3, EN55022, EN55024
UL-DEMKO EN60950, Low voltage directive
Australia AS/NZS3260
AS/NZS3548

PJ-TX100W/E/U ver 1.2
6
1.25 INCLUDED ACCESSORIES
Power Cord
PJ-TX100W: Asia/Australia; (US, Euro, UK) x 1
PJ-TX100E: For Europe; (UK, Euro) x 1
PJ-TX100U: For US/Canada;(US) x 1
Component Cable (3 m) x 1
Wireless Remote Control Unit
"AAA" Batteries x 2
Lens Cover x 1
Rivet x 1
Strap x 1
10 (*) Language Operator's Manual x 2 (total 10 language)
15 (**) Language Safety Instructions x 1
10 (*) Language Quick Guide x 1
(*) (English, French, Spanish, German, Italian, Dutch, Norwegian, Portuguese, Simplified Chinese, Korean)
(**) (English, French, Spanish, German, Italian, Norwegian, Dutch, Portuguese, Simplified Chinese,
Traditional Chinese, Korean, Swedish, Russian, Finnish, Polish)

PJ-TX100W/E/U ver 1.2
7
OUTWARD

PJ-TX100W/E/U ver 1.2
8
2. ENVIRONMENTAL CONDITION
2.1 AMBIENT TEMPERATURE
Operating 0 ~ 35 °C
Storage -20 ~ 60 °C
2.2 HUMIDITY
Operating 10 ~ 85% RH
Without condensation
Storage 10 ~ 85% RH
Without condensation
2.3 ALTITUDE From sea level to 6000 feet
2.4 SHOCK (HANDLING) Withstand 50 mm drop on bottom on wooden table
2.5 GAS No corrosive gas and combustible gas existed
2.6 ELECTROSTATIC DISCHARGE
Withstands 10 times 10kV electrostatic discharge from a 150 pF
Capacitor through a 100 ohms resistor on any exterior surface of the unit

PJ-TX100W/E/U ver 1.2
9
3. IMAGE QUALITY
Apply following condition except where noted.
• Apply heat-running for 10 minutes or more before checking
• Ambient temperature is 23 °C
• Whisper: Normal,
•Gamma: Default #1
•Temp: Custom (offset 0, gain 0)
• Vertical Lens shift: 1:1, Horizontal Lens shift: 1:1
• Zoom: Wide max, Foot adjust: Retracted (Set should be even with the ground.
3.1 BRIGHTNESS
960 lumens minimum
(Note 1) ANSI 9 point Standard measurement at Screen size 40inch, Meter CL-200
Brightness = Luminance intensity averaged over 9 points x screen area
Typical 1200 lumens (Target)
Brightness: Max. Contrast: Max.
3.2 BRIGHTNESS UNIFORMITY
BRIGHTNESS UNIFORMITY 60% minimum, 70% typical (Target)
(Note) ANSI Standard measurement
Brightness uniformity = Minimum of the four corner measurements/average of 9 points measurements
Zoom position: wide, Brightness/Contrast; Default setting
1/6W1/3W
1/6H
1/3H
1/20W
1
/
20H

PJ-TX100W/E/U ver 1.2
10
3.3 CONTRAST RATIO
120:1 minimum 200:1 Typical (Target)
(Note) ANSI standard measurement. Vertical Lens shift: 10:0.
(A black-and-white " chessboard " pattern consisting of 16 equal rectangles)
All white, all black 720:1 Minimum, 1200:1 Typical (Target)
(Note) Vertical Lens shift: 1:1.
3.4CIE SATURATION Brightness/Contrast at Default setting
x y
White 0.30±0.04 0.34±0.04
Red 0.65±0.04 0.345±0.04
Green 0.34±0.04 0.65±0.04
Blue 0.14±0.04 0.04±0.04
3.5 COLOR UNIFORMITY (Target) at Default setting
100% white, ANSI 9 points
ExtremeCorner ∆x ±0.045, ∆y ±0.045 ∆x ±0.045, ∆y ±0.045
50% white, ANSI 9 points
ExtremeCorner ∆x ±0.045, ∆y ±0.045 ∆x ±0.045, ∆y ±0.045
(Note) ∆x, ∆y are the difference from the center point
Brightness, Contrast; Default setting
3.6 MISCONVERGENCE, FOCUS
(1) MISCONVERGENCE
1.0 pixel maximum at the center and top left, 1.2pixel others
(Note)
Misconvergence is the distance between G crosshatch lines and the other colors crosshatch lines
(2) FOCUS SHIFTS / FOCUS UNBALANCE / Flare (Screen Size 64”)
Test Condition: Image size 70 inches, Zoom: wide, Contrast and Bright at default setting
Observing distance; 1.8 m from screen (at the projector)
Test method; Focus on the center of the image white letter E (H x W x; 5 x 3 pixels, 1 pixel gap)
on black background.
Every letter E should be resolved in whole area of the image.

PJ-TX100W/E/U ver 1.2
11
3.7 DOT DEFECT
(1) SPECIFICATIONS
ITEM Max. NUMBER
Mode Color A-Zone B-zone Total Transmittance See below *1
Green 0 0 0 More than 5%
Sparkle Red 0 0 0 More than 10%
Blue 0 0 0 More than 20%
Green * * 5 Area is more than 75 %
Black Red * * 5
Blue * * 5
* ; not defined
• A sparkle mode defect and a faint sparkle mode defect
When a pixel is partially or completely transmittable during an entirely black raster.
• A black mode defect
When a pixel is partially or completely turned off during an entirely white raster.
• Transmittance
In case of a partial defect, the transmittance is average of a whole pixel transmittance.
• Line defect
There are no two or more continuous defects. (Sparkle mode)
There are no three or more continuous defects. (Black mode)
*1 Sparkle mode
Use Dot pattern with brightness and contrast maximum.
(Make Dot pattern by 0.7Vp-p R,G, B on black (0Vp-p white) background.)
Sparkle mode is brighter than signal (0.7Vp-p white) dots with a ND filter.
Transmittance level of ND filter is stated on (1)specifications.
(2) DEFINITION OF ZONE
B zone
A zone
1H
1V
V/4
V/2
H/4 H/2

PJ-TX100W/E/U ver 1.2
12
4. ELECTRICAL
4.1 VIDEO SIGNAL INPUT
(1) Composite
Amplitude 1.0 ± 0.1 Vp-p at 75 Ωterminated
Input impedance 75Ω
(2) S-VIDEO
Amplitude Y: 1.0 ± 0.1 Vp-p at 75 Ωterminated with composite sync
C: 0.3 ± 0.1 Vp-p at 75 Ωterminated
Input impedance 75Ω
(3) Component
Amplitude Y: 1.0 ± 0.1 Vp-p at 75 Ωterminated with composite sync
CB/PB,CR/PR: 0.7± 0.1 Vp-p at 75 Ωterminated
Input impedance 75 Ω
4.2 RGB SIGNAL INPUT
(1) Analog RGB
Amplitude 0.7 ± 0.1 Vp-p at 75 Ωterminated
Input impedance 75 Ω
(2) Sync. TTL level
(3) Computer compatibility
Resolution H x V Refresh Rate Horizontal Frequency Standard Type Note
640x480 59.9 Hz 31.5 kHz VESA VGA-3
640x480 66.7 Hz 35.0 kHz Mac 13"
640x480 72.8 Hz 37.9 kHz VESA
640x480 75.0 Hz 37.5 kHz VESA
640x480 85.0 Hz 43.3 kHz VESA
640x480 120.0Hz 61.8 kHz
800x600 56.3 Hz 35.2 kHz VESA
800x600 60.3 Hz 37.9 kHz VESA
800x600 72.2 Hz 48.1 kHz VESA
800x600 75.0 Hz 46.9 kHz VESA
800x600 85.1 Hz 53.7 kHz VESA
800x600 120.0 Hz 77.2kHz
832x624 74.5 Hz 49.7 kHz Mac 16"
1024x768 60.0 Hz 48.4 kHz VESA
1024x768 70.1 Hz 56.5 kHz VESA
1024x768 75.0 Hz 60.0 kHz VESA
1280x960 60.0 Hz 60.0 kHz VESA
1280x1024 60.0 Hz 64.0 kHz VESA
Note: SVGA/XGA /SXGA input signals shall be displayed but picture quality might be rude.

PJ-TX100W/E/U ver 1.2
13
4.3 AUDIO SIGNAL INPUT
Amplitude NONE
Input impedance NONE
4.4 REMOTECONTROL
Range with new battery
Front Front: 5.0m minimum ±30 ° (Horizontal, Vertical)

PJ-TX100W/E/U ver 1.2
14
5. PACKING
5.1 PACKAGING FORM
See Figure 5.1
Packaging materials; Plastic bag, cushion and carton box
ＷｘＨｘＤ 440 x 300 x 375 mm (nominal)
Gross weight 8 kg
Pallet size 1245 x 1036 x 938 mm (W x H x D)
5.2 VIBRATION
There shall be no damage or change of performance out of this specification after the
following vibration test with factory fresh packing.
Vibration frequency 7 ~ 100 Hz 20 minutes per axis (10 minutes one way)
Acceleration Bottom 1.0G
Back 0.8G
Side 0.8G
Duration 2.5 hours (1.5h for Bottom, 0.5h for Back & Side)
5.3 DROP TEST
There shall be no damage or change of performance out of this specification after the
following drop test.
This test shall be done with factory fresh packing and the following sequence.
1. Surface 1 90 cm
2.Surface 2 90cm 4 6
3.Surface 4 90cm 3
4. Surface 5 90 cm
5. Surface 6 90 cm
6.Surface 3 90cm 5
7. Edge 1-2 90 cm ２
8. Edge 1-4 90 cm
9. Edge 1-5 90 cm
10. Edge 1-6 90 cm 1

PJ-TX100W/E/U ver 1.2
15
Figure 5.1