HiVi S600 User manual

-
+
+
HiVi惠威.美 国
HiVi Acoustics, Inc.
11630 Goldring Road，Arcadia, CA 91006, USA
Tel: [phone] Fax: [phone]
HiVi惠威.中 国
珠海惠威科技有限 公司
广东省珠 海市联港 工业区大 林山片区东 成路南1号
电话：[phone] 传真：[phone]
客户服务 热线：400-090-9199
因设计变更等原因，所示资料可能与实物不符，恕不另行通知
理想
拉
压
压
S600

Option One:if you don't want to change the structure of car, and install the tweeter
before steering wheel or beside the door of car,then you can use this mode.
1、Take semicircle double sides stick EVA, g et rid of one side protecting paper and
stick this on the place of installation of tweeter(as drawing).
2、Get rid of another protecting paper of EVA,then stick speaker at the fixed place.
3、Adjust the orientation of speaker so as to reach the best sound quality.
Note:The merit of this kind of installation is that don't need to change the car,the demerit is
that can't fix the tweeter well enough.
2、lnstallation of Tweeter
Please be sure your automobile is turned off before proceeding any further.
Please connect according to the following circuit diagram
The second installing method : if you want to install tweeter in the car door
or other covert place of car, go like this way:
1.Open the front face of tweeter by screwdriver.
2.Change the narrow surround of the front face of tweeter into wide surround fro
-nt face, then, it will sink into the round hole.
3.Cut a round hole (50mm) at the selected position.
4.Put the tweeter into round hole and fix it stably.
band edge front cover
tweeter unit
flat keel back cover
Circuit diagram
Congratulations on your purchase of HiVi car loudspeakers.to ensure proper
installation and operation please read this manual carefully.
this manual is to aid in your speakers installation.however there is no specific
information of automobile dismantling or assembling for each car model. if you
have no experience in this area,we recommend you consult an experienced auto
-motive service center.
For more information about our company and our products, please visit our
website at www.hivi.com.
3、Installation of crossover
1、Open the enclosure of the crossover,and exert and press towards both sides,
then raise it upwards.
2、Instal the crossover on the car door or other places.
4、Connection
-
+
+
(Wite)
Crossover
Tweeter
Audio Input(-)
Audio Input(+)
(Red)
(Wite)
(Red)
(Wite)
(Red)
Woofer
pull
press
1、Installation of Woofer
、
1 According the demand then stick the airproof mat on the place of lnstallation.
、
2 According the opening hole template then open the speakerhole and the snail
installation hole in suitable place.
、
3 lf the depth is notenough,can use some mats on the place of installation then
can add some depth.
、
4 lnstall the net on the speaker as drawing.
Installation
gasket seal with EVA-side
audio wire
wood gasket
1、
2、
Two-sided glue EVA
1、Remove wire Insulator(about 5mm).
2、Wrest wire core tightly.
3、In order to protect circuit , avoid not to cause short circuit between the
anode (+)and cathode(-)cables of loudspeaker.
Notice
Do not overlap the cables!
Specification
Component system
Mid/woofer
Tweeter
Model
Sensitivity
Frequency response
Max power
Power handling
Rated impendence
Mouting size
Cut out size
Mouting depth
High pass
damping frequency
Low pass
damping frequency
outside diameter
of middle/woofer
Crossover point
60-20KHz
4KHz
4、
3、
HiVi Acoustics, Inc.
11630 Goldring Road，Arcadia, CA 91006, USA
Tel: [phone] Fax: [phone]
Zhuhai HiVi Technology Co., Ltd.
No. 1, South Dongcheng Road Liangang Industrial Zone
Zhuhai, Guangdong, 519045, P.R. China
Tel: [phone] Fax: [phone]
press
S600