Hochiki America Corporation FN-600X-220 User manual

FN-600X-220
Power Supply/Charger
Installation Guide
Rev. 020918

- 2 -
Overview:
The FN-600X-220 is a power supply that converts a 220VAC 50/60Hz input to a 12VDC or 24VDC regulating output
(see specifications below).
Input:
•
Input 220VAC 50/60Hz, 1.5 amp.
Output:
•
12VDC or 24VDC selectable output.
Specifications:
Supervision:
•
AC fail supervision (form “C” contacts).
•
Low battery supervision (form “C” contacts).
•
Battery presence supervision (form “C” contacts).
•
6 amp continuous supply current at 12VDC or 24VDC.
•
Filtered and electronically regulated outputs.
•
Short circuit and thermal overload protection.
Battery Backup:
•
Built-in charger for sealed lead acid or gel type batteries.
•
Automatic switch over to stand-by battery when AC fails.
•
Maximum charge current 0.7 amp.
•
Zero voltage drop when switched over to
battery backup.
Additional Features:
•
AC input, DC output and BAT trouble LED indicators.
•
Power supply, enclosure, cam lock and battery leads.
Enclosures:
FN-600X-R220 (Red Enclosure)
FN-600X-C220 (Charcoal Grey Enclosure)
Enclosure Dimensions (H x W x D) :
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
Installation Instructions:
The unit should be installed in accordance with article 760 of The National Electrical Code as well as NFPA 72 and all
applicable Local Codes.
1.
Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two upper
screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 4).
2.
The power supply is pre-wired to the ground (chassis). Connect main incoming ground to the provided green
grounding conductor lead. Connect unswitched AC power (220VAC, 50/60 Hz to terminals marked [L, G, N]
(Fig. 1, pg. 4). Use 14 AWG or larger for all power connections (Battery, DC output, AC input). Use 22 AWG to
18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
Keep power-limited wiring separate from non power-limited wiring (220VAC, 50/60Hz Input, DC Output,
Battery Wires). Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
3.
Set the unit to the desired DC output voltage by setting SW1 (Fig. 1, pg. 4) to the appropriate position
(Power Supply Voltage Output Selections Chart, pg. 2).
4.
Measure output voltage before connecting any devices to ensure proper operation. Improper or high voltage will
damage these devices. When servicing the unit, AC mains should be removed.
5.
Connect devices to be powered to terminals marked [+ DC -], carefully observing correct polarity (Fig. 1, pg. 4).
6.
For Access Control applications batteries are optional. When batteries are not used, a loss of AC will result in the
loss of output voltage. When the use of stand-by batteries is desired, they must be lead acid or gel type.
7.
Connect appropriate signaling notification devices to terminals marked [AC FAIL & BAT FAIL] (Fig. 1, pg. 4),
supervisory relay outputs.
Note: When used in fire alarm, burglar alarm or access control applications, “AC Fail” relay should be utilized
to visually indicate that AC power is on. To delay report for 6 hours, cut “AC Delay” jumper (Fig. 1, pg. 4).
8.
Please ensure that the cover is secured with the provided Key Lock.
Power Supply Output Specifications:
Output Switch Position
12VDC SW1 - CLOSED (Fig. 1a, pg. 4)
24VDC SW1 - OPEN (Fig. 1a, pg. 4)

- 3 -
Stand-by Specifications (total current shown):
Output 4 hr. of Stand-by &
5 Minutes of Alarm
24 hr. of Stand-by &
5 Minutes of Alarm
60 hr. of Stand-by &
5 Minutes of Alarm
12VDC / 40AH Battery Stand-by = 6.0 amp
Alarm = 6.0 amp
Stand-by = 1.0 amp
Alarm = 6.0 amp
Stand-by = 300mA
Alarm = 6.0 amp
24VDC / 12AH Battery -------- Stand-by = 200mA
Alarm = 6.0 amp --------
24VDC / 40AH Battery Stand-by = 6.0 amp
Alarm = 6.0 amp
Stand-by = 1.0 amp
Alarm = 6.0 amp
Stand-by = 300mA
Alarm = 6.0 amp
LED Diagnostics:
Red (DC) Green (AC) Red (BAT) Status
ON ON ON Normal operating condition.
ON OFF ON Loss of AC. Stand-by battery supplying power.
OFF ON OFF No DC output. Battery Trouble
OFF OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
ON ON OFF Battery missing / Low battery.
Terminal Identification:
Terminal Legend Function/Description
L, G, N Connect 220VAC 50/60Hz to these terminals: L to hot, N to neutral. Do not use the [G] terminal.
+ DC --- 12VDC / 24VDC @ 6 amp continuous non power-limited output.
AC Fail
NC, C, NO
Indicates loss of AC power, e.g. connect to audible device or alarm panel. Relay normally
energized when AC power is present. Contact rating 1 amp @ 28VDC. AC or brownout fail is
reported within 1 minute of event. To delay reporting of up to 6 hrs., cut “AC delay” jumper and
reset power to unit.
Bat Fail
NC, C, NO
Indicates low battery condition, e.g. connect to alarm panel. Relay normally energized when DC
power is present. Contact rating 1 amp @ 28VDC. A removed battery is reported within
5 minutes. Battery reconnection is reported within 1 minute.
Low battery threshold:
12VDC output threshold set @ approximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
+ BAT --- Stand-by battery connections. Maximum charge current 0.7 amp.
Use 14 AWG or larger for all power connections.
Wiring:
Note: Take care to keep power-limited circuits separate from non power-limited wiring (220VAC, Battery).
Maintenance:
Unit should be tested at least once a year for the proper operation as follows:
Output Voltage Test: Under normal load conditions, the DC output voltage should be checked for proper voltage level
(refer to Power Supply Voltage Output Specifications chart).
Battery Test: Under normal load conditions check that the battery is fully charged, check specified voltage both at
battery terminal and at the board terminals marked [+ BAT ---] to ensure that there is no break in the battery connection wires.
Note: Maximum charging current under discharge is 0.7 amp.
Note: Expected battery life is 5 years, however, it is recommended changing batteries in 4 years or less if needed.

- 4 -
Fig. 1
CAUTION: De-energize unit prior to servicing. For continued protection against
risk of electric shock and fire hazard replace fuse with the same type and rating
5A, 250V. Do not expose to rain or moisture.
Door
Wire
Strap
(from
Enclosure
to Door)
Do Not Touch
Exposed Metal Parts
220VAC
power mains
non power-
limited
AC Delay
Battery & AC
Supervision
Circuit
(power-limited)
OPEN - 24V
CLOS ED - 12V
+ BAT ---
Battery conn ection
(non power-limited)
+ DC - --
DC Output to devices
(
non power-limited
)
Earth
Ground
Fig. 1a
OPEN - 24V
CLOSED - 12
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
Enclosure Dimensions:
CAUTION: Optional rechargeable stand-by batteries must match
the power supply output voltage setting.
Keep power-limited wiring separate from non power-limited.
Use minimum 0.25" spacing.
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
* The door is included
1.20” 0.75”
12.5”
(318mm)
0.75”
1.20”
(31mm)
(19mm)
11.0”
(279mm) (31mm)
1.40”
(36mm)
5.10”
(130mm)
0.9375”
(24mm)
1.40”
(36mm)
5.10”
(130mm)
13.0”
(330mm)
5.10”
(130mm)
6.5625”
(167 mm)
0.9375”
(24mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
1.0”
(25mm)
1.0”
(25mm)
1.0”
(25mm)
10.5”
(267mm)
1.0”
(25mm)
Hochiki America Corp.
7051 Village Drive, Suite 100, Buena Park, CA 90621-2268, 714-522-2246, Fax: [phone], www.hochiki.com
IIFN-600X-220 G02N
1.40”
(36mm)
4.85”
(123mm)
4.85”
(123mm)
1.40”
(36mm)
1.20”
(31mm)
3.25”
(83mm)
V
AC DC BA T
5A 250V
L G N
BA T FAI L N C C NO NC C NO AC FAI L
(19mm)