Holiday Living TG90P3813S03 User manual

ITEM #0580578
9 FT PRE-LIT MCKENNEY
FIR TREE
MODEL #TG90P3813S03
Français p. 7
1
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
AB1598 Lowes.com

2
PACKAGE CONTENTS
1
1
1
1
1
DESCRIPTIONPART QUANTITY
1
Tree Top
1
2Tree Middle Section 1
Tree Middle Section 2
Tree Middle Section 3
Tree Bottom Section
1
3
4
Tree Stand
5
6
7
8Power Cord (preassembled)
Foot Pedal (preassembled)
1
Lowes.com
5
4
3
2
1
6
7 8
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover

Lowes.com
3
CAUTION
RISK OF FIRE
Do not replace attachment plug. It contains a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5-volt lamps only.
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
insulation.
products that may be attached to the product. Replace the fuse as per the user servicing instructions
a short-circuit may be present and the product should be discarded.
SAVE THESE INSTRUCTIONS.
PREPARATION
contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 5 minutes.
No Tools Required for Assembly.
SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the
product.

Lowes.com
4
3. Remove protective cap from tree middle section 1 (2). Insert tree
middle section 1 (2) into tree bottom section (1).
4. Remove protective cap from tree middle section 2 (3). Insert tree
middle section 2 (3) into tree middle section 1 (2).
ASSEMBLY INSTRUCTIONS
2. Remove protective cap from tree bottom section (1). Insert tree
bottom section (1) into tree stand (6).
2
1
3
4
6
1
78
7
3
2
6
78
2
1
6
78
Eye Bolt
Click
Eye Bolt
1. Open tree stand (6) by pulling apart the legs of the stand so that
they are snapped into an x-shape, place the tree stand (6) on a
level surface.
When inserting the bottom section of the tree into the assembled
stand (6), insert and turn the eyebolts into the stand and tighten
until the tree pole is firmly secured.
NOTE: To close the tree stand (6), remove the eyebolts, press
the metal button and fold the legs together.
6

Lowes.com
5. Remove protective cap from tree middle section 3 (4). Insert tree
middle section 3 (4) into tree middle section 2 (3).
6. Insert tree top (5) into the top hole of the tree middle section 3 (4).
5
• Unplug extension cord from the wall outlet first and then remove all ornaments and decorations.
• Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to
remove from section below and fold all branches toward the pole.
• Continue by gently lifting straight up each section(s) from the section below
and fold all branches toward the pole until the bottom section is removed from
the tree stand. Cover the protective cap on the poles to avoid damaging the
internal parts. (See Fig. A)
• Carefully place all tree sections into shipping box and tape it shut.
• When not in use, please store your tree in a cool, dry place away from sunlight.
Exposing your tree to excessive heat or humidity may damage your tree.
CARE AND MAINTENANCE
Grip plastic
not glass
Pull straight out
Remove lamp base Replace lamp base
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
out of lamp holder.
BULB REPLACEMENT INSTRUCTIONS:
5
78
7
1
6
2
3
4
5
6
7
3
6
6
78
78
4
7
5
4
7. This tree does not require shaping.
Plug in the power cord (5) to any 120V outlet. Press the pedal
switch (6) to turn on the tree lights.
Fig. A

Lowes.com
6
PRINTED IN CHINA
Holiday Living & Design®is a registered
trademark of LF, LLC. All rights reserved.
Burned fuse
FUSE REPLACEMENT INSTRUCTIONS:
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2. Open fuse cover by sliding open the fuse access cover on top of
attachment
3. Remove fuse carefully: turn fuse holder over, remove fuse.
5. Close fuse cover by sliding closed the fuse access cover on top of
attachment plug.
FUSED LAMP REPLACEMENT
WARNING - Risk of fire: This product employs overload protection (fuse lamp) in
each series light circuit to provide overload protection in addition to the fuse(s)
located in the plug. Do not replace the fuse lamp contained in this set with any
other type of lamp, use only spare fuse lamps provided with this product. In case
of a burnt out FUSED lamp, the entire series of 50 lamps will be out. To replace
the fused lamp:
1. Grasp the plug and remove from the receptacle or other outlet device. Do not
unplug by pulling the cord.
2. Locate the fused lamp with gray color lamp holder. Pull the burnt fused lamp
and plastic lamp base straight out of the lamp holder.
3. Replace with a spare fused lamp. The fused lamp can be distinguished by a
gray lamp base and an additional clear plastic cover.
4. Plug in the lights again.
REPLACEMENT PARTS LIST
Fuse Bulb
B
A
For replacement parts, call our customer service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST,
Monday - Friday.
A
B
Fuse
Bulb
CFuse Lamp
T NPAR DESCRIPTIO
Fuse Lamp
C
TROUBLESHOOTING
Bulb broke.
1. Start with the first unlit bulb, then gently push (don't twist)
each bulb firmly into the socket.
2. Look and feel for a broken bulb in the socket or an
empty socket where a bulb has fallen out.
Mark the bulb with a piece of tape and unplug the tree
before removing the bulb socket and any fragments.
Replace the broken bulb.
Replace any burned out bulbs.
One bulb will not light.
A section will
not light.
Bulb is broken.
1. Bulb is loose.
2. Bulb broke or
fell out.
Bulb burned out.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION