Holiday Living TG90P3813S05 User manual

ITEM #0580578
9 FT PRE-LIT MCKENNEY
FIR TREE
MODEL #TG90P3813S05
Français p. 9
1
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
AB1640 Lowes.com

2
PACKAGE CONTENTS
1
1
1
1
1
DESCRIPTIONPART QUANTITY
1
Tree Top
1
2Tree Middle Section 1
Tree Middle Section 2
Tree Middle Section 3
Tree Bottom Section
1
3
4
Tree Stand
5
6
7
8Power Cord (preassembled)
Foot Pedal (preassembled)
1
Lowes.com
5
4
3
2
1
6
7 8
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover

Lowes.com
3
CAUTION
RISK OF FIRE
Do not replace attachment plug. It contains a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5-volt lamps only.
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
insulation.
products that may be attached to the product. Replace the fuse as per the user servicing instructions
a short-circuit may be present and the product should be discarded.
SAVE THESE INSTRUCTIONS.
PREPARATION
contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 5 minutes.
No Tools Required for Assembly.
SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the
product.

Lowes.com
5
4
3
2
1
6
4
ASSEMBLY INSTRUCTIONS
1. Remove tree stand and tree sections from box.
4. a. Locate “Pull Here” tab and corresponding Cinch Handle.
b. Hold Cinch Clip firmly with one hand and press down on clip.
c. With Cinch Clip depressed, pull clip away from tree until all
branches are released.
d. Locate all clips on the same tree section then repeat above
procedures to release the corresponding branches.
4
Cinch Clip
Cinch
Handle A
B
C
PULL HERE
1
5
4
3
2
1
6
3. Insert tree bottom section (1) into the tree stand (6).
3
2
Eye Bolt
Click
Eye Bolt
2. Open tree stand (6) by pulling apart the legs of the stand so that
they are snapped into an x-shape, then place the tree stand (6) on
a level surface.
When inserting the bottom section of the tree into the assembled
stand (6), insert and turn the eyebolts into the stand and tighten
until the tree pole is firmly secured.
NOTE: To close the tree stand (6), remove the eyebolts, press
the metal button and fold the legs together.
6

2
5. Remove the protective cap from tree bottom section (1)
and insert tree middle section 1 (2).
5
6. Release all branches using the same procedures
described in step 4.
5Lowes.com
6
7. Add tree middle section 2 (3), tree middle section 3 (4) and tree
top (5) using the same procedures described in steps 5 and 6. 7
8. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that
all wires are free of branch hinges.
9. Insert green label plug into the wall outlet. The entire tree should now be lit. If some bulbs do not
light or flicker, search for any loose plugs and/or broken, loose or missing bulbs. Connect the
plugs or replace the bad bulbs promptly in order to maintain the performance and life expectancy
of your pre-lit tree.
10. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest
from the pole and fan out one to the right, one to the left and one at the center of the main stem.
11. After shaping the entire tree, slightly upsweep all branch tips for a uniform
look. Shift branches to fill any gaps. The tree is now complete and ready to be decorated.

6Lowes.com
STORAGE INSTRUCTIONS
1. Detach Tree Top and store it in box.
Unplug cord from the wall outlet and then remove all ornaments and decorations.
1
2. a. Cover the protective cap of the Tree Middle Section 3.
b. Hold Cinch Handle with right hand.
c. Hold Cinch Clip firmly with left hand and press down
on clip. Pull handle toward you while pushing away
cinch clip until the upper branches of Tree Middle Section 3
are folded completely.
2
A
B
C
4
4. Repeat the procedures described in step 2 for tree middle
section 2 and tree middle section 1.
3
3. Detach Tree Middle Section 3 and put it into the box.

Lowes.com
7
• When not in use, please store your tree in a cool, dry place away from sunlight.
Exposing your tree to excessive heat or humidity may damage your tree.
BULB REPLACEMENT INSTRUCTIONS:
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2. Lift up to unsnap locking tab; then pull lamp and plastic base
straight out of lamp holder.
3. Replace lamp with only 2.5-volt push-in type lamp provided with product.
CARE AND MAINTENANCE
Grip plastic
not glass
Pull straight out
Remove lamp base Replace lamp base
FUSE REPLACEMENT INSTRUCTIONS:
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2. Open fuse cover by sliding open the fuse access cover on top of
attachment plug toward blades.
5
5. Detach Tree Middle Section 1 and Tree Middle Section 2
and put them into the box.
6
6. Cover the protective cap of Tree Bottom Section, then fold.
7
7. Detach Tree Bottom Section from tree stand and pack
them into the box.

Lowes.com
8
PRINTED IN CHINA
Holiday Living & Design®is a registered
trademark of LF, LLC. All rights reserved.
Burned fuse
3. Remove fuse carefully: turn fuse holder over, remove fuse.
4. Risk of fire. Replace fuse only with 3-amp, 125-volt fuse for decorative
lighting string(provided with product). If applicable, replace fuse only
with 5A-amp, 7A-amp or 10-amp, 125-volt fuse for cord-set (see fuse
current on cord-set plug).
5. Close fuse cover by sliding closed the fuse access cover on top of
attachment plug.
FUSED LAMP REPLACEMENT
WARNING - Risk of fire: This product employs overload protection (fuse lamp) in
each series light circuit to provide overload protection in addition to the fuse(s)
located in the plug. Do not replace the fuse lamp contained in this set with any
other type of lamp, use only spare fuse lamps provided with this product. In case
of a burnt out FUSED lamp, the entire series of 50 lamps will be out. To replace
the fused lamp:
1. Grasp the plug and remove from the receptacle or other outlet device. Do not
unplug by pulling the cord.
2. Locate the fused lamp with gray color lamp holder. Pull the burnt fused lamp
and plastic lamp base straight out of the lamp holder.
3. Replace with a spare fused lamp. The fused lamp can be distinguished by a
gray lamp base and an additional clear plastic cover.
4. Plug in the lights again.
REPLACEMENT PARTS LIST
Fuse Bulb
B
A
For replacement parts, call our customer service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST,
Monday - Friday.
A
B
Fuse
Bulb
CFuse Lamp
T NPAR DESCRIPTIO
Fuse Lamp
C
TROUBLESHOOTING
Bulb broke.
1. Start with the first unlit bulb, then gently push (don't twist)
each bulb firmly into the socket.
2. Look and feel for a broken bulb in the socket or an
empty socket where a bulb has fallen out.
Mark the bulb with a piece of tape and unplug the tree
before removing the bulb socket and any fragments.
Replace the broken bulb.
Replace any burned out bulbs.
One bulb will not light.
A section will
not light.
Bulb is broken.
1. Bulb is loose.
2. Bulb broke or
fell out.
Bulb burned out.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION