Holman QCS-2 SERIES User manual

1
®
®
®
®
R
CONVEYOR
TO
A
S
TE
R
MO
DEL
QCS2
,
QCSe2
,
RCS2
,
R2e SERIE
S
Q
CS3, QCSe3 SERIE
S
I
nstallation an
d
Op
eratio
n
I
nstruction
s
2M-Z10651 Rev. G 1/26/201
5
Q2-600H-208V

2
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
6WDUUHVHUYHVWKHULJKWWRFKDQJHVSHFL¿FDWLRQVDQGSURGXFWGHVLJQZLWKRXW
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
UHJXODWLRQVWKHVSHFL¿FDWLRQVFRQWDLQHGLQWKLVVKHHWDUHVXEMHFWWRFKDQJH
ZLWKRXWQRWLFH:KLOH6WDU,QWHUQDWLRQDO+ROGLQJV,QF&RPSDQ\H[HUFLVHV
JRRGIDLWKHIIRUWVWRSURYLGHLQIRUPDWLRQWKDWLVDFFXUDWHZHDUHQRW
responsible for errors or omissions in information provided or conclusions
UHDFKHGDVDUHVXOWRIXVLQJWKHVSHFL¿FDWLRQV%\XVLQJWKHLQIRUPDWLRQ
SURYLGHGWKHXVHUDVVXPHVDOOULVNVLQFRQQHFWLRQZLWKVXFKXVH
MAINTENANCE AND REPAIRS
&RQWDFW\RXUORFDODXWKRUL]HGVHUYLFHDJHQWIRUVHUYLFHRUUHTXLUHGPDLQWHQDQFH
3OHDVHUHFRUGWKHPRGHOQXPEHUVHULDOQXPEHUYROWDJHDQGSXUFKDVHGDWHLQWKHDUHDEHORZDQGKDYHLWUHDG\ZKHQ
you call to ensure a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Business DPWRSP&HQWUDO6WDQGDUG7LPH
Hours:
Telephone: [phone]
Fax: [phone]
E-mail [email protected]
[email protected]
 :DUUDQW\#VWDUPIJFRP
Website: ZZZVWDUPIJFRP
Service Help Desk
Authorized Service Agent Listing
5HIHUHQFHWKHOLVWLQJSURYLGHGZLWKWKHXQLW
or
for an updated listing go to:
Website: ZZZVWDUPIJFRP
E-mail [email protected]
Mailing Address:6WDU,QWHUQDWLRQDO+ROGLQJV,QF&RPSDQ\
10 Sunnen Drive
St. Louis, MO 63143
U.S.A

3
TABLE OF CONTENTS
General Installation Data ......................................................4
Uncrating & Inspection.........................................................4
Assembly & Installation .......................................................4
Electrical Connection............................................................4
QCS & RCS
Operation .............................................................................5
Cooking Procedures ............................................................5
Toaster Components ............................................................5
Daily Operation ...................................................................6
Operating Hints & Safety ....................................................6
QCSe & RCSe
QCSe Operation ..................................................................7
Start-up ................................................................................8
Daily Operation ...................................................................8
Operating Hints & Safety ....................................................8
Toaster Components ............................................................8
Programing
Conveyor Speed.................................................................9
Programing Values for Menu Items ...................................9
Cleaning ...............................................................................10
Maintenance Procedures ...................................................... 11
Trouble Shooting Guide.......................................................12
Warranty...............................................................................13
Wiring Diagrams
QCS2 & 3, RCS2 & 3, wired series ...................................14
QCS2 & 3, RCS2 & 3, wired parallel ................................14
QCS2 & 3, RCS2 &3, 3 wired in series .............................15
QCS2, RCS2 w/fan switch series .......................................15
QCS2 & 3, RCS2 & 3, 3 wired in series w/bun mode .......16
QCSe, 4 wired in series ......................................................16
QCSe, 6 wired in series ......................................................17
QCSe, 6 wired in parallel ...................................................17
QCS3, 6 wired in series, with fuses....................................18
R2-600N & R2-600BN ......................................................18
Exploded View / Parts List
R2-600N (Narrow) .............................................................20
QCS2 & 3, RCS2 & 3 ........................................................22

4
GENERAL INSTALLATION DATA
This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with
the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If
equipment is received in damaged condition, either apparent or concealed, a claim must be made
with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.
INSPECTION & ASSEMBLY
UNCRATING AND INSPECTING
Unpack the unit and components from the shipping container. Remove all visible packing material
DQGWKRVHIURPLQVLGHWKHFRRNLQJFKDPEHU,IGDPDJHLVGLVFRYHUHG¿OHDFODLPLPPHGLDWHO\ZLWK
the carrier that handled the shipment. Do not operate the unit if it was damaged during shipping.
ASSEMBLY AND INSTALLATION
7KHXQLWZDVVKLSSHGIXOO\DVVHPEOHGDQGUHDG\WRSOXJLQWRDVWDQGDUGRXWOHWVSHFL¿HGIRULWVYROWDJH
DQGDPSGUDZ,ILPSURSHUHOHFWULFDOVXSSO\LVGHWHUPLQHGFRQWDFWDTXDOL¿HGHOHFWULFLDQSULRUWRXVLQJ
the unit. Removal and replacement of the power cord and plug will void the warranty. For assistance,
contact your local authorized service agent for service or required maintenance.
Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
%HIRUHXVLQJWKHXQLWIRUWKH¿UVWWLPHZLSHGRZQWKHH[WHULRUZLWKDGDPSFORWK
Allow enough space around the toaster for adequate ventilation. Do not operate the unit without the
crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit
and follow their instructions.
ELECTRICAL CONNECTION
Before making any electrical connection to this unit, check that the power supply is adequate for the
voltage, amperage and requirements stated on the rating plate.
A wiring diagram is included herewith.
Disconnect the unit from the power source before installing or removing any parts.
Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect
equipment to power without proper ground connections. Improper grounding may result in personal
injury or fatality.
DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM THE
PLUG.
CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE
DATA PLATE OF THE UNIT.
CAUTION
WARNING
CAUTION
WARNING

5
OPERATION
ROTARY POWER SAVER SWITCH
For toasters equipped with a Rotary Power Saver Switch, turn clockwise or counterclockwise to get in
the following positions.
FULL POWER
When in this position your equipment is at full power and ready to use.
OFF ROTARY
Two off positions are provided, a single rotation to either direction will shut the unit off.
STANDBY
The standby position reduces the power consumption by 75%. Using this position during the quiet
times will save electricity, and keep the toaster warm. When needed, turn the switch to FULL POWER.
Recovery time is about 30 seconds.
CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE
SHOULD BE TAKEN WHILE USING THIS UNIT.
COOKING PROCEDURES
BREAD TOASTING
Some toasters are equipped with a swinging heat shutter at the toaster entrance. This shutter will move
out of the way as the product passes under it.
1) Turn the power saver to FULL POWER.
2) Set the conveyor speed to HIGH.
3) If your toaster is equipped with separate top and bottom heat controls set them both
at HIGH.
4) Allow warm up time of 5 to 10 minutes.
5) Place a sample product on the conveyor belt to test the settings.
•If toasting is too light, turn conveyor speed control counterclockwise to a slower speed.
•If toasting is too dark, turn heat control to a lower heat.
(NOTE: Some products may require adjustment of the top and bottom heat controls in
order to achieve the desired results)
TOASTER COMPONENTS
CAUTION
Q C S
LOAD UP
CRUMB TRAY
POWER SAVER SWITCH
HEAT CONTROLS
SPEED CONTROL
FRONT
AIR INTAKE FAN
HIGH LIMIT RESET
POWER CORD
IL1386

6
DAILY OPERATION
Check the power cord to insure that it is plugged into a proper outlet.
Set the heat control knobs to desired temperature.
$OZD\VDOORZPLQXWHVRISUHKHDWWLPHEHIRUHORDGLQJWKHXQLWZLWKSURGXFW)DLOXUHWRDOORZVXI¿FLHQW
preheat time will result in unsatisfactory cooking until the unit reaches operating temperature.
OPERATING HINTS AND SAFETY
Disconnect power to the unit with the switch at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Turn Power Saver Switch to Standby during idle periods. It will take only a few minutes to
regain operating temperature.
Do not leave the unit at high temperature when not in use or during idle periods.
7KLVZLOOFDXVHIRRGSDUWLFOHVDQGJUHDVH¿OPWRFDUERQL]H
CAUTION
Q C S

7
QCSe & RCSe OPERATION
The Holman QCSe conveyor toaster comes with pre-programmed factory default settings for TOAST,
MUFFINS, and BAGELS. The operator may change these setting at any time. A button labeled OTHER is
provided to allow the operator to program settings for additional product(s).
Press TOAST and TST will appear in the display.
Press MUFFIN and MUF will appear in the display.
Press BAGEL and BGL will appear in the display.
Press OTHER and OTH will appear in the display.
LIGHT and DARK buttons are used to change the conveyor speeds
ZKHQLQWRDVWPXI¿QRUEDJHOPRGHV
Pressing the (LIGHT) button once will increase the conveyor speed
by 15%. Pressing twice (XLIGHT) will increase the conveyor speed by
30%.
Pressing the (DARK) button once will decrease the conveyor speed
by 10%. Pressing twice (XDARK) will decrease the conveyor speed by
20%.
Note: After 60 seconds the conveyor speed will return to the pre-
programmed setting.
The factory default settings are as follow:
TOAST AND OTHER BAGEL:
TOP HEAT 9 TOP HEAT 9
BOTTOM HEAT 9 BOTTOM HEAT 9
CONVEYOR 59 CONVEYOR 24
OTHER: POWER SAVER:
TOP HEAT 9 TIME (minutes) 60
BOTTOM HEAT 9 HEAT 5
CONVEYOR 59
The QCSe toaster is equipped with a Power Saver Switch (SAVER)
that reduces the power used by the toaster after a pre-programmed
period of time. This Power Saver Switch has three modes:
ON: Unit is in pre-programmed power saving setting.
OFF: Power Saver mode is turned off.
AUTO ON: Power Saver turns on when there has been no activity
for a programmed length of time.
The operator may adjust the level of power reduction for the saver
mode. (Note: conveyor may move slowly when in saver mode.)
Two buttons (+) and (-) are used when increasing or decreasing the
value of each programmable setting.
A red LED light located at the lower portion of the control panel label
will indicate if the value for top heat, bottom heat or conveyor speed is
being adjusted.
Q C S
®
e

8
CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD
BE TAKEN WHILE USING THIS UNIT.
START UP
When the toaster has been plugged into a suitable outlet and power supply, the word OFF will be
displayed on the L.E.D. read out.
A. Press the ON/OFF button once to turn on the toaster. The toaster will now enter into pre-heat and
PREHT will be displayed (the elements will begin to glow but the conveyor and fan motor will not
turn on).
B. After one minute, the fan motor will turn on and the conveyor will begin turning at the previously
saved setting (for initial start up, the drive motor will operate at the factory default setting).
C. After four minutes, the display will show the last used program selection i.e. TOAST, BAGEL,
MUFFIN or OTHER (for initial startup, TOAST will be the last program selected).
DAILY OPERATION
Check the power cord to insure that it is plugged into a proper outlet.
Press the ON/OFF button once to turn the toaster on.
Press the button a second time to turn the toaster off.
NOTE::KHQWKHWRDVWHULVWXUQHGRIIWKHIDQDQGFRQYH\RUPRWRUVZLOOFRQWLQXHWRUXQIRU¿YHPLQXWHV
The words COOL and DOWNZLOOEHDOWHUQDWHO\GLVSOD\HGGXULQJWKDWWLPH$IWHU¿YHPLQXWHVWKHZRUG
OFF will be displayed until the ON/OFF button is pressed again.
For units equipped with a POWER SAVER feature, the three operating modes are:
ON Unit has entered the pre-programmed level of power savings.
OFF Power Saver feature is turned off.
AUTO If the toaster has been idle for a pre-set period of time, the unit enters Power Saver
mode until one of the menu buttons has been pressed.
Once the toaster has been pre-heated, the menu buttons can be pressed to change to TOAST, BAGEL,
MUFFIN, or OTHER.
OPERATING HINTS AND SAFETY
Disconnect power to the unit with the ON/OFF button at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Do not leave the unit at high temperature when not in use or during idle periods. This will cause food
SDUWLFOHVDQGJUHDVH¿OPWRFDUERQL]H
TOASTER COMPONENTS
LOAD UP
CRUMB TRAY
CONTROLS
LCD DISPLAY
FRONT
AIR INTAKE FAN
HIGH LIMIT RESET
POWER CORD
IL1385
CAUTION
Q C S
®
e
CAUTION

9
PROGRAMING
A. CONVEYOR SPEED (temporary setting)
The conveyor speed is programmable with a range from 0 to 99 with 0 being the slowest and 99 being
the fastest. Each menu item can have independent conveyor speed settings.
The LIGHT and DARK buttons can be used to temporarily change the conveyor speed.
Pressing the LIGHT button once will increase the conveyor speed by 15%. The word LIGHT
will be displayed. Pressing twice will increase the conveyor speed by 30% and XLIGHT will
now be displayed.
Pressing the DARK button once will decrease the conveyor speed by 15%. The word DARK
will be displayed. Pressing twice will decrease the conveyor speed by 30% and XDARK will
now be displayed.
NOTE: After 60 seconds, the conveyor speed will return to the pre-programmed setting.
WHEN USING THE LIGHT AND DARK BUTTONS TO ADJUST THE CONVEYOR SPEED
FOR A SINGLE ORDER OF PRODUCT, IT IS IMPORTANT TO REMEMBER TO ALLOW
THE PRODUCT ALREADY IN THE TOASTER TO EXIT BEFORE CHANGING THE
SPEED SETTING.
B. PROGRAMING VALUES FOR MENU ITEMS
7RPDNHDSURJUDPFKDQJHWRWKHWRSKHDWERWWRPKHDWRUFRQYH\RUVSHHG\RXPXVW¿UVWEHLQWKH
menu item you want changed. Example: to change the programmed conveyor speed for bagels, the
display must read BAGEL. To change the programmed conveyor speed for TOAST, the display must read
TOAST and so on for each menu item.
1) Select the menu item you want to change i.e. TOAST, MUFFIN, BAGEL or OTHER.
2) Press and hold both ( + ) AND ( - ) buttons for 3 seconds until the display goes
blank, release the buttons and the display will show three characters for the menu
item elected and the last two characters for the current value setting, i.e. TST, MUF,
BGL and OTH7KHUHG/('OLJKWIRUWRSKHDWDWWKHERWWRPRIWKHODEHOZLOOÀDVK
3) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the top heat.
4) Press the button for the menu button again and the red L.E.D. for the bottom heat
ZLOOÀDVK
5) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the bottom heat.
6) Press the button for the menu button again and the red L.E.D. for the conveyor
VSHHGZLOOÀDVK
7) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the conveyor
speed.
8) To skip one feature setting with out making any changes, press the menu item button
RQHWLPHDQGWKHUHG/('OLJKWIRUWKHQH[WLWHPZLOOQRZÀDVK
9) To change the POWER SAVER values press the SAVER button or to save your new
setting(s), and exit the program mode press the menu button.
10) The last two characters in the display will show MN for minutes.
 7KH¿UVWWKUHHFKDUDFWHUVZLOOEHQXPHULFDOWRUHSUHVHQWWKHWLPHVHWWLQJ
12) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the savor mode
time. The minimum value is 15 minutes to maximum value of 480 minutes.
13) Press the SAVER button to change the power reduction using the ( + ) or ( - ) buttons
to increase or decrease the setting.
14) Press the POWER SAVER button to save changes and to exit.
Q C S
®
e

10
CLEANING
Preventive maintenance for your Holman toaster consists of the following recommended cleaning
procedures. To keep your toaster in its top operating condition, these steps should be performed on a
daily or weekly as indicated.
A. Clean air intake on bottom of unit.
B. For lightly soiled conveyor belts, turn conveyor speed control to fastest setting (100) and
wipe with a damp cloth (daily) For heavily soiled conveyors, turn conveyor speed control to
fastest setting and wipe with a light abrasive pad (as needed).
C. Turn main power saver switch to the OFF position. Disconnect unit from power source.
D. After the unit cools, remove interior crumb tray (as shown below) and clean.
Slide crumb tray back into position.
E. Wipe exterior surface of unit.
DO NOT IMMERSE OR LET THE UNIT
STAND IN WATER.
DO NOT HOSE DOWN THE UNIT OR THE
TABLE/COUNTER IF THE UNIT IS ON THE
TABLE/COUNTER.
KEEP AWAY FROM RUNNING WATER.
CLEAN
OPERATE
CRUMB TRAY REMOVAL
WARNING
Q C S
Q C S
®
e

11
MAINTENANCE PROCEDURES
A. REPLACING HEATER TUBES
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove the enclosure.
3) Remove heater tube wire from terminal block connection, keeping top and
bottom wires separate.
4) Lift heater tube retainers by loosening retaining screws and sliding the retainer plate up.
Hand tighten the plate to hold it up so the heater tubes will slide out freely.
5) Gently, pull defective heater tube out of unit.
6) Gently, put new heater tube into unit.
7) Loosen retainer screws and slide the retainer back into place. Tighten the screw to
secure the retainer in place over the ends of the heater tubes.
B. REPLACING FAN MOTOR
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove screws from the enclosure and the back panel at rear of unit.
3) Remove the enclosure and the back panel.
4) Unplug power supply cord from fan motor.
5) Remove (4) screws, which hold fan motor and grill to bottom of unit and remove fan.
6) Put replacement motor and grill in place and secure to the bottom of unit with screws.
7) Reconnect power supply cord to fan motor.
8) Replace back panel and enclosure. Fasten with screws removed in step 2.
C. REPLACING BELT DRIVE MOTOR
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove enclosure and back panel.
3) Remove sprocket from motor shaft, using an Allen wrench and loosening the set-screw.
4) Remove the wire from terminal block connecting the drive motor to internal wiring.
On units rated 208 or 240 volts, note which color leads are being used for these connections
and which lead is capped with white tape. The new motor should use the same arrangement.
5) Remove screws holding motor in place and remove motor from unit.
6) Put new motor in place and attach loosely with mounting screws.
7) Replace sprocket on motor shaft.
NOTE: The two sprockets should line up parallel with each other, so the chain does not twist
any during operation. Also the hub gets installed closets to the motor.
8) Slide motor until the drive chain has about 1/4” slack when lightly pushed at the center of its top
open run. See chain tensioning illustration.
9) Tighten screws to secure motor.
10) Rewire leads same as removed in step 4.
11) Replace side panel and control box cover.
D. CLEANING AIR INTAKE ONCE A WEEK
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Place unit on its backside.
3) Use a vacuum cleaner and or a damp cloth to clean
the air intake. This procedure should be done at least once a week.
E. LUBRICATE THE CHAIN & SPROCKETS EVERY 6 MONTHS
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove enclosure exposing chain drive.
3) Using an extreme pressure, synthetic chain lubricant with a
temperature range up to 400°F. Apply liberally onto chain
and sprockets. This grease is available as part no. 1P-Z12397.
4) Replace enclosure, Reconnect power source and test unit.
1/4”
QCS/RCS Chain Tension

12
TROUBLESHOOTING GUIDE
A. UNIT WILL NOT HEAT, CONVEYOR BELT WILL NOT MOVE.
1) Be sure the main circuit breaker is switched to the ON position.
2) Check to see if the toaster is plugged in and all controls are turned to the ON position.
B. UNIT HAS HEAT ONLY ON ONE SIDE, CONVEYOR BELT TURNS FREELY.
1) Call the Star Service Help Desk at [phone], as heating element may need replacing.
C. CONVEYOR WILL NOT TURN, UNIT HEATS PROPERLY.
To check for mechanical binding:
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove 2 screws holding enclosure to the bottom of the unit.
3) Set unit on the legs and remove 4 screws on the back of the toaster.
4) Slide the enclosure off the unit and remove the back panel.
5) Loosen the four screws that hold the drive motor in place.
6) Slide the motor up allowing the drive chain to be removed from the sprockets.
7) Move the conveyor belt by hand to check for mechanical binding. If conveyor moves freely,
call the Star Service Help Desk at [phone], as the drive motor and/or speed control may
need replacing.
8) Replace the enclosure by sliding it forward towards the front of the unit.
The front edge of the enclosure will slide beneath the toaster front.
D. HEAT LIMIT SWITCH (RESET)
Your Holman conveyor toaster is equipped with an automatically activated heat limit switch that
interrupts the heater tube connections if the ambient temperature in the control box exceeds
190°F (88C). This switch can be reset manually by pushing the red button under the toaster as
shown in the Toaster Components Illustration on Page 5 & 8.
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Check to see if air intake area in the bottom center of the control box cover is free of dust,
grease or other obstructions.
3) Check if crumb tray is in place. NEVER OPERATE UNIT WITHOUT CRUMB TRAY IN PLACE
AS THIS CAUSES OVERHEATING IN THE CONTROL BOX.
 ,IQRREVWUXFWLRQVWRWKHDLUÀRZFDQEHIRXQGDQGLIWKHFUXPEWUD\LVLQSODFH
call the Star Service Help Desk at [phone] or email; [email protected] for
assistance, or contact an authorized service agent near you.
E. CONVEYOR TURNS AT ONE SPEED REGARDLESS OF SPEED
CONTROL SETTING.
1) Call the Star Service Help Desk at [phone] or email; [email protected], as speed
control should be replaced, or contact an authorized service agent near you.
F. PRODUCT STICKING TO CONVEYOR OR SLIDE
Your Holman conveyor toaster is designed to toast product that is at current room temperature.
DO NOT attempt to put frozen, refrigerated, or any butter or a butter substitute material in the
toaster. Doing so may cause it to come out doughy or very moist, as well as possibly sticking to
parts of the unit.
1) Follow the cleaning procedures listed on page 10.

1
3
2M-44
9
7-2 11
/
21
/
14
Th
e forego
i
ng warranty
i
s
i
n
li
eu of any an
d
a
ll
ot
h
er warrant
i
es expresse
d
or
i
mp
li
e
d
an
d
const
i
tutes t
h
e ent
i
re warranty
.
FO
R A
SS
I
S
TANC
E
Sh
ou
ld
you nee
d
any ass
i
stance regar
di
ng t
h
e Operat
i
on or Ma
i
ntenance of any Star equ
i
pment; wr
i
te, p
h
one, fax or ema
il
our Serv
i
ce De
p
artment
.
In a
ll
correspon
d
ence ment
i
on t
h
e Mo
d
e
l
num
b
er an
d
t
h
e Ser
i
a
l
num
b
er of
y
our un
i
t, an
d
t
h
e vo
l
ta
g
e or t
y
pe of
g
as
y
ou are us
i
n
g
.
ALL:
*
Pop-Up Toasters
*
Butter D
i
spenser
s
*
Pr
e
tz
el
M
e
r
ch
an
dise
r
s
(
Model 16PD-A Only
)
*
Pastr
y
Displa
y
Cabinet
s
*
Nacho Chip Merchandiser
s
*
Accessor
i
es of any
ki
n
d
*
S
neeze
G
uard
s
*
P
i
zza
O
vens
(
Model PO12 Only
)
*
Heat Lamps
*
Pumps-Manua
l
Vi
s
it
ou
r W
ebs
it
e
at:
www.star-mfg.com
fg
E
mai
l
:
[email protected]
@g
TH
O
R
OUG
HLY IN
S
PECT Y
OU
R
U
NIT
O
N ARRIVAL
T
hi
s un
i
t
h
as
b
een teste
d
for proper operat
i
on
b
efore
l
eav
i
ng our p
l
ant to
i
nsure
d
e
li
very of your un
i
t
i
n perfect con
di
t
i
on
.
However
,
t
h
ere are
i
nstances
i
n w
hi
c
h
t
he unit ma
y
be dama
g
ed in transit. In the event
y
ou discover an
y
t
y
pe of dama
g
e to
y
our product upon receipt,
y
ou must immed
i
atel
y
contact the transportation
company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit
.
L
IMITED E
Q
UIPMENT WARRANT
Y
All workmanship and material in Star products have a one (1)
y
ear limited warrant
y
on parts & labor in the United States and Canada. Such warrant
y
is limited
to t
h
e or
i
g
i
na
l
purc
h
aser on
l
y an
d
s
h
a
ll
b
e effect
i
ve from t
h
e
d
ate t
h
e equ
i
pment
i
s p
l
ace
d
i
n serv
i
ce. Star's o
bli
gat
i
on un
d
er t
hi
s warranty
i
s
li
m
i
te
d
to t
h
e repa
i
r
of defects without char
g
e, b
y
the factor
y
authorized service a
g
enc
y
or one of its sub-a
g
encies. Models that are considered portable
(
see
b
e
l
ow
)
s
h
ou
l
d
be
tak
e
n
to the closest Star service a
g
enc
y
, transportation prepaid.
>
S
tar w
ill
not assume any respons
ibili
ty for
l
oss of revenue
.
>
O
n all shipments outside the United States and Canada, see International Warrant
y.
*
The warranty period for the Ultra-Max, Hot Plates, Griddles, Charbroilers is (3) years parts & labor
.
*
The warranty period for the Star-Max, Charbroilers, Griddles, Hot Plates, Fryers & Finishing Oven is (2) years parts & labor.
&
*
The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
e seri
*
7
K
H
Z
DUUDQ
W\
S
HU
L
R
G
I
RU W
KH
&K
URPH0D
[
*
U
LGGO
HV
L
V
¿
YH



\
HDUV
RQ
WK
H
JULGG
GOH
IDFH
VXUID
6
HH
G
HWD
LO
H
G
Z
DUUDQ
W
\
S
URY
LG
H
G
ZL
W
K
XQ
L
W

*
The warranty period for Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to
reasonable
'X
UD
7HF
FRDWLQ
JV
I
U
RP
L
PSURSH
U
FOHDQLQ
J
PDLQWHQDQFH
XVH
RI
P
H
WDOOL
F
XWHQ
HQVLOV
RU
DVLYH
DEUD
F
OHDQHUV

DE
UD
V
L
YH
SDGV

S
URGXF
W
L
GH
QWL¿
H
U
V
DQ
G
point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the
ject tha comes in continuous contact w
th the roller coating. T
“non-st
i
c
k
”
p
ro
p
ert
i
es of suc
h
mater
i
a
l
s.
>
This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts
egular catalog items
nly. Star's warranty on "S
an
d
n
i
nety
(
90
)
d
ays on
l
a
b
or.
>
This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or
tam
m that is disassembled o
nty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Autho
the Service
ce Center's sub-agency.
>
This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated
e occurs from
ranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrar
the Installation and
y to
Operating instructions.
g instructions.
>
This warranty is not valid on Conveyor Ovens
nty is not valid on Conveyor Ovens
unlessunless
a "start-up/check-out" has been performed by a Factory Authorized Technician.
a "start-up/check-out" has been performed by a Factory Authorized Technician
PARTS WARRANTY
TS WARRANTY
Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part is
re sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part i
is
NO
T warrante
d.
RVICES NOT COVERED BY WARRANT
SERVICES NOT COVERED BY WARRANTY
WARRA
PORTABLE EQUIPMENT
Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
that include travel time and m
bills
These products should be taken to the Service Agency for repair:
aken to the Service Agency for repa
ak


7UD
YHO
WLP
LPH
D
Q
G
P
LOHD
J
H
G
UHQGHUHG
EH\R
EH\RQG
WK
H

PLOH
PL
UDGLXV
GL
O
OLPLW
2.
Mileage and travel time on portable equipment
d travel time on portable equipment
(see below)
belo
3
.
Labor to replace such items that can be replaced easily during a daily cleaning
o replace such items that can be replaced easily during a daily c
d eas
e
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.
removable kettles on fryers, knobs, grease drawers on g
nobs, g
e dra
4.
Installation of equip
quipment

 'DPD
J
HV
GXH
W
R
LPSURS
SURSHU
DOODWLRQ
LQVWDOOD
WLRQ
6
.
Damages from abuse or misuse
misu
use
7.
Operated contrary to the Operating and Installation Instructions
llation I
Operatin
g and In
8
.
C
l
ean
i
n
g
of equ
i
pmen
t
9.
Seasoning of griddle plates
te
es
10
.
tage conversions
ge conversio
Volta
11.
11
Gas conversions
onversions
Gas c
12
.
P
il
ot
li
g
h
t a
dj
ustment
13
.
Miscellaneous ad
j
ustments
14
.
Th
ermostat ca
lib
rat
i
on an
d
b
y-pass a
dj
ustment
 5HVHWW
L
QJ
RI
FL
U
FXLW
E
U
H
D
NH
U
V
R
UVD
I
HW
\
FR
QWU
ROV
R
U
UHVHW
EX
WW
R
Q
V
 5HSODFHPHQ
W
RI
EX
O
EV
 5HS
O
DFHPHQ
W
R
I
I
XVH
V
 5H
S
D
L
U
RI
G
DPD
JH
F
U
H
DW
HG
G
XU
L
Q
J
W
UDQV
L
W

G
H
OL
YHU
\

LQVWDOODWLRQ
NT
2
5
F
U
H
DW
HG
E\
D
F
W
V
RI
*
R
G
*
7KH 0RGHO

)'
))
))
)
U\HU
*
7
K
H0R
G
H
O

72
$
7
RDVWHU 2YHQ
*
7K
H
0
RGH
O
-
5

R
]

3RSFRUQ
0
D
F
KLQ
H
*
7
K
H
0
RGH
O

&
0
$


&
0
$
&
KHHVH 0HOWHU
*
7
K
H0R
G
H
O

0&

0
&

0&
3
+
R
W
)
RR
G
0
HUF
K
DQ
GL
VHUV
*
7K
H
0
RGH
O

1
&
3
:

1
&
3
:
1D
F
K
R
&
KLS3RSFRU
Q
:
DUPHU

*
All Hot Dog Equipmen
t
e
xcept Roller
G
r
i
lls
&
Drawer Bun Warmers
.
*
A
ll
Nac
h
o C
h
eese Warmers
e
xce
p
t Model 11WLA Series Nacho Cheese Warmer.
*
All Condiment Dispensers except the Model HPD
&
S
PD
S
er
i
es D
i
spenser
.
*
A
ll
Spec
i
a
l
ty Foo
d
Warmers except Model 130R, 11RW Series, and 11WSA Series.
*
$
OO
4
&6

5&
6
6HU
L
HV
7R
D
V
W
H
U
V
exce
p
t Model QCS3 & RCS3 Series
.
*
All Fast
S
teamer Models
e
xcept D
i
rect
C
onnect
S
er
i
es
.

14
FAN MOTOR
POWER SAVER
3
1
RESET/HIGH LIMIT
BOTTOM
4
2
HEAT
MOTOR
DRIVE
H1
PILOT
L1
H2
L2
14GA CORD
POWER SUPPLY
PILOT
H1
L1
H2
L2
CONTROL
SPEED
CONTROL SIDE
LEFT SIDE
BOTTOM HEAT
TOP HEAT
WHITE
3 BLACK
BLACK
WHITE
BLACK
BLUE FOR 120 & 240V
1 BLACK
WHITE BLACK
8 WHITE
6
11
12
13
10
WHITE FOR 208V
5 BLACK
7 BLACK
MOTOR WIRE
IS 18GA
GND
BLUE
2
4
WHITE
9
BLACK
BLACK
WHITE
14
WHITE
WHITE
BLACK
TOP HEAT
(OPTIONAL ELEMENTS ARE SHOWN HIDDEN)
15 BLACK
®
MODEL:
QCS2 & 3 Wired Series
RCS2 & 3 Wired Series
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2240 Rev - 7/2007
FAN MOTOR
POWER SAVER
3
1
RESET/HIGH LIMIT
BOTTOM
4
2
HEAT
MOTOR
DRIVE
H1
PILOT
L1
H2
L2
14GA CORD
POWER SUPPLY
PILOT
H1
L1
H2
L2
CONTROL
SPEED
CONTROL SIDE
LEFT SIDE
2E-Z10406
BOTTOM HEAT
TOP HEAT
TOP HEAT
WHITE
3 BLACK
WHITE
BLACK
BLUE FOR 120 & 240V
1 BLACK
WHITE BLACK
8 WHITE
6
11 BLACK
13 BLACK
12
10
ALL WIRES ARE 12 CA UOS
WHITE FOR 208V
1N-E2010 12GA 150C BLACK
1N-E2011 12GA 150C WHITE
5 BLACK
7 BLACK
MOTOR WIRE
IS 18GA
GND
BLUE
2
4
WHITE
9
BLACK
WHITE
W
HITE
15 BLACK
14
WHITE
2E-Z10406
(OPTIONAL ELEMENTS ARE SHOWN HIDDEN) (OPTIONAL ELEMENTS ARE SHOWN HIDDEN)
®
MODEL:
QCS2 & 3 Wired Parallel
RCS2 & 3 Wired Parallel
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2241 Rev - 7/2007

15
®
FAN MOTOR
POWER SAVER
3
1
RESET/HIGH LIMIT
BOTTOM
4
2
HEAT
MOTOR
DRIVE
H1
PILOT
L1
H2
L2
14GA CORD
POWER SUPPLY
PILOT
H1
L1
H2
L2
CONTROL
SPEED
CONTROL SIDE
LEFT SIDE
2E-Z10406
BOTTOM HEAT
TOP HEAT
TOP HEAT
WHITE
3 BLACK
WHITE
BLACK
BLUE FOR 120 & 240V
1 BLACK
WHITE BLACK
8 WHITE
6
11 BLACK
13 BLACK
12
10
ALL WIRES ARE 12 CA UOS
WHITE FOR 208V
1N-E2010 12GA 150C BLACK
1N-E2011 12GA 150C WHITE
5 BLACK
7 BLACK
MOTOR WIRE
IS 18GA
GND
BLUE
2
4
WHITE
9
BLACK
WHITE
WHITE
15 BLACK
14
WHITE
2E-Z10406
Ref: SOW# 2E-Z10380
MODEL:
QCS2 & 3, 3 Wired in Series
RCS2 & 3, 3 Wired in Series
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2242 Rev - 7/2007
FAN MOTOR
POWER SAVER
3
1
RESET/HIGH LIMIT
4
2
MOTOR
DRIVE
14GA CORD
POWER SUPPLY
CONTROL
SPEED
CONTROL SIDE
LEFT SIDE
2E-Z1O406
BOTTOM HEAT
WHITE
3 BLACK
12 BLACK
WHITE
BLACK
BLUE FOR 120 & 240V
1 BLACK
WHITE BLACK
9 BLACK
11 810
ALL WIRES ARE 14 CA UOS
WHITE FOR 208V
1N-E2020 14GA 150C BLACK
1N-E2021 14GA 150C WHITE
5 WHITE
MOTOR WIRE
IS 18GA
GND
BLUE
2
4
WHITE WHITE
2E-Z10406
BLACK
FRONT HEAT
MIDDLE HEAT
FAN SWITCH
7 BLACK
6 WHITE
®
MODEL:
QCS2 & w/Fan Switch, Series
RCS2 & w/Fan Switch, Series QCS3 & w/Fan Switch, Series
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2243 Rev A 7/2007

16
®
SERIES HEATER TUBES
ALL WIRES ARE 12 CA UOS
1N-E2010 12GA 150C BLACK
1N-E2011 12GA 150C WHITE
MODEL:
QCS2 & 3, Wired Series w/ Bun Mode & Fuses
RCS2 & 3 Wired Series w/ Bun Mode & Fuses
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2244 Rev A 4/14/08
FAN MOTOR
POWER SAVER
3
1
RESET/HIGH LIMIT
BOTTOM
4
2
HEAT
MOTOR
DRIVE
H1
PILOT
L1
H2
L2
14GA CORD
POWER SUPPLY
PILOT
H1
L1
H2
L2
CONTROL
SPEED
LEFT SIDE
BOTTOM HEAT
TOP HEAT
TOP HEAT
MOTOR WIRE
IS 18GA
BUN MODE
CONTROL SIDE
3 BLACK
4 WHITE
BLUE FOR 120 & 240V
1 BLACK
WHITE BLACK
8 WHITE
6
13 BLACK
12 WHITE
10
WHITE FOR 208V
5 BLACK
GND
WHITE
9
BLACK
WHITE 14 WHITE
2E-Z10406
11 BLACK
BLACK
17
BLACK
18
WHITE
15
BLACK
16
WHITE
BLACK
7
FUSE
FUSE
20 BLACK
3 BLACK
14 WHITE
2 WHITE
BLACK
4 WHITE
2 WHITE
WHITE OR BLUE
®
MODEL:
QCSe 4 Tube wired Series
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
SK2282 Rev - 7/2007
4
WHITE
3BLACK
2
BLACK
1
BLACK
5
BLACK
7BLACK
8 WHITE
6
WHITE
QCSe
OT1
HT1
HB1
F1 M1
L1
120V
OT2
F2
L2
M2
120V 240V 240V HT2
HB2
TOP HEAT
BOTTOM HEAT

17
MODEL:
QCSe 6 Tube wired Series
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
®
SK2283 Rev - 7/2007
4
WHITE
3BLACK
2
BLACK
1
BLACK
5
BLACK
7BLACK
8 WHITE
6
WHITE
TOP HEAT
BOTTOM HEAT
QCSe
OT1
HT1
HB1
F1 M1
L1
120V
OT2
F2
L2
M2
120V 240V 240V HT2
HB2
4
WHITE
3BLACK
2
WHITE
1
BLACK
5
BLACK
7BLACK 8 WHITE
6
WHITE
QCSe
OT1
HT1
HB1
F1 M1
L1
120V
OT2
F2
L2
M2
120V 240V 240V HT2
HB2
BOTTOM HEAT
TOP HEAT
MODEL:
QCSe 6 Tube wired Parallel
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
®
SK2284 Rev - 7/2007

18
®
SK2365 REV. - 4-14-08
CERTAIN INSTANCES MAY NOT BE AVAILABLE ILLUSTRATIVE PURPOSES ONLY AND IN SOME ITEMS ARE INCLUDED FOR
QCS-3, 6 ELEMENTS
WIRED SERIES WITH
FUSES
FAN MOTOR
RESET/HIGH LIMIT
BOTTOM
4
2
HEAT
MOTOR
DRIVE
H1
PILOT
L1
H2
L2
14GA CORD
POWER SUPPLY
PILOT
H1
L1
H2
L2
CONTROL
SPEED
CONTROL SIDE LEFT SIDE
BOTTOM HEAT
TOP HEAT
TOP HEAT
3 BLACK
4 WHITE
BLACK
1 BLACK
WHITE BLACK
6
11 BLACK
13 BLACK
12
10
WHITE FOR 208V
5 BLACK
7 BLACK
MOTOR WIRE
IS 18GA
GND
WHITE OR BLUE
WHITE
9 BLACK
WHITE
WHITE
15 BLACK
FUSE
FUSE
2 WHITE
4 WHITE
14 WHITE
BLACK
16 WHITE
1
3
8 WHITE
RCS-2-600N
2M-Z16972 rev~
RIGHT SIDE
(CONTROLS)
POWER SUPPLY
WHT
BLK
GND
DRIVE
MOTOR
RESET/HIGH
LIMIT
SPEED
CONTROL
BLK
COOLING
FAN
BLU
BLK WHT
BLK
RCS-2-600BN
2M-Z16803 revA
RIGHT SIDE
(CONTROLS)
POWER SUPPLY
WHT
BLK
GND
DRIVE
MOTOR
RESET/HIGH
LIMIT
SPEED
CONTROL
BLK
COOLING
FAN
BLU
BLU FOR
120/240V
WHT FOR 208V
BLK WHT
BLK

19

20
SK2664 Rev. A 7/22/13
1
2
3
6789
4
11
512
812
14 15
16
24
25
26
27
28
29
31
35
39
40
41
38
37
34
33
34
32
30
17
18
19
20
21
22
23
12
Nameplate
10
MODEL: R2-600N:
Narrow Conveyor Toaster