HOLOVISION VIO2 Service manual
INSTALLATI N
INSTRUCTI NS
501 E. Goetz Ave.
Santa Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax 800-362-0002
H L VISI N
Manual Type 1.1.0.10-RF
Holovision VI 2 with Essex 265 Controller
Specifications
Access Control
Essex 5 button keypad
2 relays
5-6 users
16.5 VAC power supply included
Internal rectifier gives optional ‘’dc out’’ for strikes
For Models
101-VIO2
107-VIO2
Communication
Holovision VIO2 is a SIP enabled intercom module
developed specifically with the custom integrator in
mind. It works with Crestron RAVA/SIP and most SIP
enabled VoIP phone systems and servers.
Speaker
Microphone
PoE+ Switch
Push Button
Link
Status
Power
Reset
Mic +
Mic -
Spk -
Spk +
Button
Button
Gnd
NC
NO
COM
12 VDC from Relay
OFF
PoE
On
VIO2
Everyday VoIP from Holovision
Essex Keypad Wiring
The 265 module comes with jumpers and MOVs prewired to the left side of the terminal stirp. Remove all wires from left side of terminal strip and wire per this diagram
*MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick back” which can be created when power is removed from
the strike.
Page 2 TYPE 1.1.0.10-RF
Essex Model 265
NC 2
NO 2
COM 2
NC 1
NO 1
COM 1
+DC
- OUT
AC
IN
Remote
Monitor
Earth
Holovision Entry
System with
Keypad
Keypadcable(22/12)l
AC Out for Strike
DC out for strike
16.5
VAC
*MOVisrecommended
Gate Strike
**N TE:
umper Wire is Required
**
Essex Model 265
NC 2
NO 2
COM 2
NC 1
NO 1
COM 1
+DC
- OUT
AC
IN
Remote
Monitor
Earth
Holovision Entry
System with
Keypad
Keypadcable (22/12)l
16.5
VAC
*MOVis recommended
Gate Strike
**N TE:
umper Wire is Required
**
**
Link
Status
Power
Reset
Mic +
Mic -
Spk -
Spk +
Button
Button
Gnd
NC
NO
COM
12 VDC from Relay
OFF
PoE
On
VI
2
Link
Status
Power
Reset
Mic +
Mic -
Spk -
Spk +
Button
Button
Gnd
NC
NO
COM
12 VDC from Relay
OFF
PoE
On
VI
2
Essex Keypad Wiring
Contact Closure for Gate Motor
*MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick back” which can be created when power is removed from
the strike.
Page 3 TYPE 1.1.0.10-RF
N TE:
umper Wire is Required
Essex Model 265
NC 2
NO 2
COM 2
NC 1
NO 1
COM 1
+DC
- OUT
AC
IN
Remote
Monitor
Earth
Holovision Entry
System with
Keypad
Keypad cable (22/12)l
The 265 module comes with jumpers and MOVs prewired to the left side of the terminal stirp. Remove all wires from left side of terminal strip and wire per this diagram
“Open”
Terminals
on Gate
Motor
16.5
VAC
Link
Status
Power
Reset
Mic +
Mic -
Spk -
Spk +
Button
Button
Gnd
NC
NO
COM
12 VDC from Relay
OFF
PoE
On
VIO2
Everyday VoIP from Holovision
Set Essex Relay ptions
Step Action
G AL: To use jumper pins on circuit board to configure standard
relay options. In this configuration, Codes 1 and 2
operate Relay 1. Codes 3, 4, 5 operate Relay 2.
1 Relay 1 and 2 activate. Only Relay 1 latch*
Code Relay 1 Relay 2
Open Latch Open Latch
Master Code No No No No
Code 1,2 Yes Yes No No
Code 3, 4, 5 No No Yes No
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Master Unlock
1, 2 Unlock
3,4,5 Unlock
1,2 Latch
3, 4,5 Latch
CCTV
Doorbell
Relay 1
Relay 2
Step Action
2 Relay 1 and 2 activate and latch*
Code Relay 1 Relay 2
Open Latch Open Latch
Master Code No No No No
Code 1,2 Yes Yes No No
Code 3, 4, 5 No No Yes Yes
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Master Unlock
1, 2 Unlock
3,4,5 Unlock
1,2 Latch
3, 4,5 Latch
CCTV
Doorbell
Relay 1
Relay 2
*LATCHING RELAY: In order to latch either relay, simply enter the code,
followed by “7”. Repeat (code, 7) in order to unlatch the relay.
The top example would be used where the driveway gate was connected to
Relay 1 (and could be locked open), and the pedestrian gate was connected
to Relay 2. (No latching possible).
Page 4 TYPE 1.1.0.10-RF
1 Enter “Master Code”.
2 Enter 115 (3 beeps).
3 Enter User Code 3.
4 Wait 5 seconds for 3 reset beeps.
Set User Code 3
Step Action
Programming of Essex Keypad
1 Enter “Master Code”
2 Enter 113 (3 beeps).
3 Enter User Code 2.
4 Wait 5 seconds for 3 reset beeps.
Set User Code 2
Step Action
1 Press “Program” switch once. (keypad will beep 4 times)
2 Once “Program” switch is pressed, you have 2 minutes to complete Step 5.
3 Press “1119”. (you will hear 3 beeps)
4 Step 5 must be completed within 5 seconds of Step 3.
5 Enter “Master Code” *
6 Wait 5 seconds for 3 beeps to confirm new “Master Code”.
Set Master Code
Step Action
1 Enter “Master Code”
2 Enter 111 (3 beeps).
3 Enter User Code 1.
4 Wait 5 seconds for 3 reset beeps.
Set User Code 1
Step Action
* MASTER CODE: The default Master Code is 13579. This should be replaced by a unique code to be used only by
your company. The Master Code can be 3 to 8 digits long.
Page 5 TYPE 1.1.0.10-RF
Programming of Essex Keypad
1 Enter “Master Code”.
2 Enter 117 (3 beeps).
3 Enter User Code 4.
4 Wait 5 seconds for 3 reset beeps.
Set User Code 4
Step Action
1 Enter “Master Code”
.
2 Enter 119 (3 beeps).
3 Enter User Code 5.
4 Wait 5 seconds for 3 reset beeps.
Set User Code 5
Step Action
1 Enter Master Code .
2 Enter address of code to be deleted (111, 113, etc.).
3 Do not enter any code until you hear 3 reset beeps.
4 Wait 5 seconds for 3 reset beeps.
Delete Any Code
Step Action
Note: User codes can be 3 to 8 digits
Page 6 TYPE 1.1.0.10-RF
1 Enter any User Code (1 -5).
2 Enter “7”. This will cause the relay to latch (subject to the jumper pin settings see Page 5).
3 To unlatch the relay, re-enter the user Code, followed by “7”.
Step Action
Latch a Relay
1 Press “Program” switch (keypad will beep 4 times).
2 Enter 1117 (3 beeps).
3 Enter 1 for every 1 second latch time, and 5 for every 5 seconds.
Examples:
6 seconds = 5, 1
8 seconds = 5, 1, 1, 1
12 seconds = 5, 5, 1, 1
4 Wait 5 seconds for 4 reset beeps.
Set Activation Time Of Relay 1 (User codes 1 & 2 - see note below)
Step Action
Programming of Essex Keypad
1 Press “Program” switch (keypad will beep 4 times).
2 Enter 1115 (3 beeps).
3 Enter 1 for every 1 second latch time, and 5 for every 5 seconds.
Examples:
6 seconds = 5, 1
8 seconds = 5, 1, 1, 1
12 seconds = 5, 5, 1, 1
4 Wait 5 seconds for 4 reset beeps.
Set Activation Time Of Relay 2 (User codes 3, 4& 5 - see note below)
Step Action
Note: The above 2 steps are actually setting the activation times for user code 1, 2 and user code 3, 4, 5. Using the
jumper pin setting as shown in “Set Essex Relay Options”, this will set activation time of Relays 1 & 2.
Page 7 TYPE 1.1.0.10-RF
Page 8 TYPE 1.1.0.10-RF
VI RAVA Quick Start
1. Plug the device into the network. Device will speak it’s IP address.
2. Navigate to device IP on a web browser.
3. Under “Configuration” please enter SIP ID for the name to be displayed, and enter the extension
of the Main RAVA Touchscreenunder “Input Call ID 0 Default is CALL:CRESTR N”
*Note out of the box the “CALL:CRESTR N” default will ring all touchpanels in the CRESTR N
call group.
4. Configure the Audio setiings. Note:RAVA peration has been designated to “Push to Talk” (PTT)
from Crestron and only this operation will be supported. Although full duplex and half duplex
are an option, these settingdo not perform best in all senarios. As a recommendation you can
experiment for the best audio settings.
AUDI SETTING BEL W ARE NLY A REC MMENDATI N
Page 9 TYPE 1.1.0.10-RF
5. Configure the relay setting under “Inbound Calls”. Configure the powered relay and the dry
contact closure. Choose any 2 to 4 digit combination
Note; By configuring the request to exit feature you can configure for either relay.
6. Once the device has been configured you can initiate the call by pressing the button
Page 10 TYPE 1.1.0.10-RF
#
%&
!"
"
!##$"#
'
Page 11 TYPE 1.1.0.10-RF
501 E. Goetz Ave.
Santa Ana, Ca 92707
Ph. 714-434-6904
Fax 800-362-0002
www.eholovision.com
This manual suits for next models
2
Other HOLOVISION Control Unit manuals
