Holystone HS210 User manual

~HOLY
..iJSTONE
Instructions For Use
HS210
otg [email protected] (USA) [email protected] (EU)
- [email protected] (CA) [email protected] (JP)
(() + 1(855) 888-6699 o www.holystone.com

Contents
1. Disclaimer Warning ..
2. Safety Guidelines
3. Maintenance ..
4. Packing Contents ..
5. Drone's Details ..
6. Low Battery Warning .
7. Transmitter Functions ..
8. Installation ...
9. Joystick Mode ..
10. Charging ..
11. Flight
Pair the Drone .....
Calibrate the Gyro ..
One Key Start Landing ....
12. Trimmer ..
13. Speed Switch ..
14. Emergency Stop .
15. 360 • Flip ..
16. Altitude-Hold Function .
I 7. Headless Mode .
18. Specification
19. Contact Us ..
20. Genera/Information ..
. 1
........... 1
. 5
. 6
7
. 7
. 8
. 8
. 9
. 10
II
12
. 12
13
14
14
15
IS
16
17
18
19

<DISCLAIMER & WARNING>
1,Please read this disclaimer carefully before using our product. This
product is not recommended for people under [he age of 14. By
using this product you hereby agree to this disclaimer and signilY
that you have read it fully You agree that you are responsible for
your own conduct and any damage caused while using this
product and its consequences You agree to use this product only
for purposes that are proper and in accordance with local
regulations, terms and aUapplicable policies and guidelines Holy
Stone may make available.
2. When using this product please be sure to strictly abide by the
specification requirements and safety guidelines stated in this
document. Any personal injury property damage, legal disputes and
ai' other adverse events caused by the violation of the safety
instructions or due to any other factor. Will NOT be Holy Stone's
responsibility.
<SAFETY GUIDELINES>
I. Check Before Use
• This product is not a toy, but it is a high precision drone that
integrates various electronic stability and control mechanisms.
Please be sure to setup [his drone carefully and correctly to ensure
safe. accident-free operation.
• Please be sure that the batteries of the drone and transmitter are
clean. undamaged and have enough power.
· Please be sure that all the propellers are undamaged and are
-1-
installed in the right orientation.
• Please do a thorough check of the product before each use.
Check for firmness of the parts, any signs of cracks and wear of the
propeller. battery power and effectiveness of the indicator, ete. If
after doing a complete check any issues are found. please refrain
from using [he drone untIl (he issue has been taken care of.
Incorrect assembly or poor control by inexperienced pilots can result
in damage to property or harm to people in an accident. Be fully
aware of your surroundings when flying and always maintain
complere conrrol of the device at all rimes.
2. Flight Environment
•• -.--
Fly in Open Areas Maintain Line Fly Below
of Sight 164 feet(SO m)
A
II
Avoid flying over or near obstacles, crowds, high VOltage
power lines trees, airport or bodies of water.
DO NOT fly near strong electromagnetic sources such as
power lines and base stations as it may affect the onboard
compass.
-2-

DO NOTuse the drone in adverse weather conditions such as
rain, snow, fog and strong wind.
3. Operations Requirements
o Please don't use this device to follow any moving vehicles
· When flying, only turn off the motor in case of an emergency.
• Please flight the drone back to you as soon as possible when the
battery is running low.
o This device should not be used while drinking alcohol if you are
feeling fatigued, taking medicine, or feeling any physical discomfort
• Stay away from the rotating propellers and motors
· Beware of the noise volume the drone produces Keep your
distance to avoid ear damage
Stay away from the rotating
propellers and motors.
No Fly Zone
4. Use of Battery
· Please ensure batteries are fined in the correct orienration as
shown in the instructions manual.
· Avoid short circuits by fitting the batteries incorrectly. and do not
crush or squeeze the batteries as chis could carry the risk of an
explosion.
-3-
• Do not mix new and old barreries as this can lead to a poor
performance of the product.
· Dispose of used batteries carefully, do not litter.
• Please keep dead batteries away from heat and fire.
• If the device is not going to be used for an extended period of
time. remove batteries to prevent potential damage from banery
leakage
• It is recommended to only use the USB charging cable that
comes WIth the drone to charge the battery.
• Don' t attempt to disassemble or modify the battery in any way
• Don't use the battery if it gives off an odor. generates heat.
become discolored or deformed. or appears abnormal in any way. If
the battery is in use or being charged, remove it from the device or
charger immediately and discontinue use
· Don't pierce the battery casing with a nail or other sharp Object.
break it open With a hammer, or step on itl
• Don't short-circuit the battery by connecting wires or other metal
Object to the positive{+j and negative{-j terminals
)
li-Po Battery Disposal & Recycling ~
Wa5l~l..iIhium-poIymbattetiesmUS noIt>eplac:e<lwiUl"OUI.ehoIdtr.uh. -..:- •
P''''•.m~con aCt local environmental orwMleagencyOl hcW<J5Ie~enc:y __ J ;
_ orlhesupplierofyourmoddoryourneare-sltJ..f'obaneryrecydingcm e". ,..
-4-

<MAINTENANCE>
1. Clear the product after each use with a clean soft cloth,
2. Avoid prolonged exposure to direct sunlight and avoid buildup of
heat on the drone.
3. This device is not waterproof and must not be submerged in
water under any circumstance. Failure to maintain the device
completely ory will result in the failure of the unit
4. Check {he charging plug and other accessories for signs of
damage Frequently. Ifany part of the device isdamaged, refrain from
flying until maintenance can be carried out
-5-
<PACKING CONTENTS>
~~
x I
x I <3
Drone Transmitter Drone Battery
~~
++
/
++
x I
x I
x I
USB Charger Propellers Screwdriver
~
~
.~
x I
~.'==
x I
Propellers Instructions
Spanner For Use
-6-

<DRONE'S DETAILS>
< TRANSMITTER FUNCTIONS>
Indicator light
Propeller B
Propeller A Speed Switch 360' FlIp
RightJ<¥tlck
left Joystick
One KeySranf
Headless Mode
landing
TumON/OFF
Propeller B
<LOW BATTERY WARNING>
CD When the drone battery runs low, the indicator lights on the
drone wi/I blink: continuously. About I minute or so the drone will
automatically land on low electricity.
@ When the transmitter battery runs low. the power indicator of
the transmitter will blink continuously and the transmitter will keep
beeping. When thiS happens, the pilot should change the new
battery Forthe transmitter.
-7-
<INSTALLATION>
Batt€f)'~
Compartment • .
. . ~BarrEries
~OTlIlCludedJ
A If you want to install the batteries, please always pay close
attention to battery polarity to make sure they are inserted
correctly.
-8-

< JOYSTICK MODE>
1. MODE 2 IIeft rlarKJ throttle MODF 2 will be deFault setting.)
,
f
Ascend
,
f
Forward
•
,
•
,
~
,
~
,
,
.s:
f
,
Dotn
Descend
,
Backward
,
Le~~Ri9ht
u:
Le~~Ri9ht Flyt.IY to
Tur urn I
-~
Left i9ht:
-~-
Left Right
2. MODE 1
To enter MODE J, turn on the transmittter while holding the" Speed
Switch" button. (Please do not release the" Speed SWitch " button
unlil the trammlHer ISpowered on.)
r 0'
,,,,,,,,,,,
UU
Tur Turn I. left ~Right Fly t Fly to
Left Right: .•• ~... Left -e Right
Up
•
~
,
Down
Forward
•
~
f
Backward
Ascend
•
Descend
-9-
<CHARGING>
,,,,
,
,
,
,
USB Adapter
[email protected])
~
Power Bank
Charging Port
Computer USB Port
(j) Connect the battery with the charger
@ Plug the charger into a USB charging port on the computer,
power bank or USB adapter 15V@ 05 to 20A I.
®Charging time: about 40-60 minutes
@ a. While the battery is charging. the charging indicator
light is Red.
b. When the battery is full charged, the charging indicator
light will turn Green .
A Before charging, please check the contents of the " Use of
Battery" section of the" Safety Guidelines" carefully
-10-

< FLIGHT>
< FLIGHT>
A All of the operations shown in this manual are
demonstrated using MODE 2.
1.Pair the Drone
<D Connect the battery port
access to the fuselage power
port.
®Turn on the transmitter. '@ Push the throttle joystick up
,then down to pair the drone
:with the transmitter The LED
indicamf lights on [he drone will
turn solid jf the drone is paired
successfully.
-11-
2. Calibrate the Gyro
As shown in the diagram above push the left and right joystick
simultaneously to the lower left corner to calIbrate the gyro. The LED
lights on me drone will blink quickly and rum solid. When you hear
2 beeps from the transmitter that indicates the calibration is
completed.
Tips: To ensure a stable flight, we suggest that the pilot
calibrates the gyro every time after pairing the drone and after
a crash.
3. One Key Startj Landing
d
1
Aher pairing( calibration, press the One Key Start button, rne
propellerswill start spinning, indicating this drone is ready co fly, and
you can conrrol this drone by using the joysrkks. Press [he One Key
Landing button again, the drone will land by itself.
-12-

<TRIMMER>
FIB Sideward Fly Trim
I ~
-~-- ~
If the drone drifts forward. hold down the throttle joystick and do
not release it while pushing [he direction joystick down to balance
the drone; If the drone drifts backwards. hold down the throttle
joystick and do not release it while pushing the direction joystick up
to balance the drone
I../R Sideward Fly Trim
I
If [he drone drifts left. hold down the throttle joystick and do not
release It while pushing the direction joystick right to balance the
drone; If the drone drifts right hold down the throttle joystick and
do not release it while pushing the drrection joystick. left to balance
tne orone.
{When you hear one long beep from [he transmitter that mcncates
the drone IS adjusted to balance.)
-13-
< SPEED SWITCH>
This drone comes with 3 speed modes {Low/ Medium/ HighJ. Press
the Speed Switch burton on [he upper left of the transmitter to
switch the speed. Increase or decrease one speed at a time. -OJ·
indicates Low speed; -DiD( indicates Medium speed and -DiDiD(
Indicates High speed.
[The Low Speed is default speed rnode.]
< EMERGENCY STOP>
A The Emergency Stop function can be only used in case of
emergency during the flight to avoid any of damage or injury.
t
Press [he upper left and upper right button of the transmitter at the
same time, the motors will stop immediately.
-14-

<ALTITUDE-HOLD FUNCTION>
I~
_-1-_,
"'---c.- +------------
'---.:~--=-~~
The drone is designed with alritude-hold function so the drone can
mamtain its altitude after you release the left stick( the left stick will
automatically spring back to the middle).
<360
0
FLIP>
When you get Familiar with all the functions of the drone, you can
try this amazing flip mode. When you fly the drone at least ra feet.
press the 360· Flip button on the upper right of the transmitter, then
push the right joystick Forward/ Backward or leFt Right. and the
drone will do a flip towards the corresponding direction.
IFyou are in MODE I, push the right joystick leFt Right or push the
lerrjoystick Forward/ Backward, and the drone will do a nip towards
the corresponding direction.
Tips: This function will perform better when the battery is fully charged.
-15-
< HEADLESS MODE>
I. After pairing/calibration. press the Headless Mode button on the
transrnluer. A beep will be heard from the transmitter, and the lights
on the drone will keep blinking. The transmitter will beep slowly to
indicate that drone is in Headless Mode.
2. Pressthe Headless Mode button again, and you will hear 2 beeps,
the LED indicator lights on the drone win be solid which indicates
the drone exits the Headless Mode.
Heacftail
Please make the pilot stays facing the same direction
as the direction that the head of the drone faces at take-off.
Under Headless Mode. the forward direction is the direction that the
head of drone faces when the drone takes off. In order to make sure
the pilot can tell drone's direction. we recommend that pilots to stay
in (he same orientation as the drone head faces when the drone
takes off. If so, when the pilot pushes the direction joystick forward.
the drone will fiy Forward. If the pilot pushes the direction joystick
backward, the drone will fly towards him/her. IFthe pilot move the
right stick left / right the drone win move left right relative to you. It
is very important that the pilot stay in the same orientation as the
drone head faces when the drone tak.esoff.
-16-

<SPECIFICATION> <CONTACT US >
DRONE
Model: HS210
Weight 2291 O.77oz
Flight Time: < 7 minutes
Motor Model: 06 I5
Operating Temperature Range 14°Fto + 104°F {-10°C to +400q
Dimensions: 80 x 80 x 30 mm
Please do not hesitate to contact us if you need further
support.
q [email protected] (USA)
[email protected] (eA)
[email protected] (EU)
[email protected] (JP)
FLIGHT BATTERY
Capacity: 220mAh
Voltage: 3.7V
Battery Type: Li-Po Battery
Charging Temperature Range: 41° to 104°F IS' to 40'C)
Charging Time: 40 - 60 minutes Idepends on charging power and
remaining battery power)
l) + 1(855) 888-6699
TRANSMITTER
Operating Frequency: 2.4 GHz
TransmissIon DIstance: 50 m [outdoors and unobstructed)
Operating Temperature Range: 32° to 104°F (0° to 400q
Barrery: I.5V AAA Barrery NOT INCLUDED)
USB CHARGING CABLE
Voltage: 5 V
Rated Power: s lOW
-)7-
-)8-

<GENERAL INFORMATION>
< GENERAL INFORMATION>
FCC Notice:
This device complies with Part J 5 of the FCC Rules.
Operation is suQject to the following two conditions:
II) This device may not cause harmful interference.
/2) This device must accept any interference received, including
interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with
the limits for a Class S digital device. pursuant to Part 15 of the FCC
Rules. These lirnitsare designed to provide reasonable protecnon
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and. if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However. there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a Circuit different from
that to which the receiver is connected
-Consult the dealer or an experienced radio/Tv technician tor
help.
-)9-
WARNING: Changes or modiFications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
RFExposure
The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This device should be
installed and operated with minimum distance 20cm between the
radiator & your body.
IC Notice:
This device complies with Canada Industry ncence-exemor RSS
standardls)
Operation is SUbject to the following two conditions:
(I J this device may not cause interference; and
12) this device must accept any interference. Including
interference [hat may cause undesired operation of the device.
CAN ICES-3 IS)
Avis d'Industrie Canada
Le present appareil est conforme aux CNR d'industrie Canada
applicables aux appareils radio exem pts de licence l.'exploita-
tion est aotonsee aux deux conditions suivanres:
I) I'appareil ne oo it pas produire de brouillage; et
2J runnsateur de I'appareil doit accepterbrouiUage radioelec-
[rique subi meme si Ie brouillage est susceptible d'encomprom-
-20-

<GENERAL INFORMATION>
ettre le foncrionnemenr. mauvais foncrionnement de rappareil.
Cet appareil nurneriquie de la c/asse 8 est conforme a ta norme
NMB-003 du Canada.
CAN NMB-3 IS)
RF Exposure
Radiation Exposure Statement:
This equipment complies with Ie radiation exposure limits set
forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm
between the radiator & your body
Declaration d'expositicn aux radiations
Cet equipement est conforme aux limites d'exposition aux
rayonnements Ie etaones pour un environnement non
conrrole, Cet equpement doit etre mstaue et uti/is€:>avec un
minimum de 20 em de distance entre lasource de rayonnement
et votre corps
HOW TO RECYCLETHIS PRODUCT
This symbol on the product or its documentation indicates that it
must not be disposed of with household waste
Uncontrolled waste disposal may harm (he environment or human
health.
Please separate your device from other types of waste to recycle it
responsibly.
-21-
<GENERAL INFORMATION>
This will help ro foster the sustainable re-use of material resources.
We invite you to contact your retailer or inquire at your local town
hallto find out where and how the drone can be recycled. :a-
SATIERYWARNING _
I. Failure to follow all the instructions may result in serious injury,
irreparable damage to the battery and may cause a fire, smoke or
explosion.
2. Always check the battery's condition before charging or using it.
3. Replace the battery if it has been dropped. or in case of adaur.
overheating, discolouration, deformation or leakage.
4. Never use anything other than the approval LiPo charger the
battery. Always use a balancing charger for LiPa cells or a lIPo cell
balancer. It is recommended that you do not to use any other
charger than the one provided with the product.
S. The battery temperature must never exceed 60·q 140·FJ
otherwise the battery could be damaged or ignite.
6. Never charger on a ftammable surface. near flammable products
or inside a vehicle/perferably place the battery In a non-ftammable
and nonconductive container}.
7. Never leave rhe battery unattended during the charging process.
Never disassemble or modify the housing's wiring, or puncture the
cells. Nways ensure that the charger output voltage corresponds to
the volrage of the battery. Do not short circuit the batteries.
-22-

<GENERAL INFORMATION>
8.·Never expose the UPo battery [0 moisture or direct sunlight or
store it in a place where temperatures could exceed 60·qcar in the
sun, for example)
9. Always keep It out of reach of children.
10. Improper battery use may result in a fire, explosion or other
hazard.
, J. Non-rechargeable batteries are nor to be recharged. Recharge-
able oarteries are only to be charged under adult supervision.
. 12. Different types of batteries or new and used batteries are not to
be mixed.
13. Batteries are to be inserted with the correct polarity.
14. The supply terminals are not to be short-circuited. Regular
examination of transformer or battery charger for any damage to
their cord, plug, enclosure and other pans and they must not be
used until the damage has been repaired.
I5. The packaging has to be kept since it coruams important
information.
16. The toy isonly to be connected to ClassII equipment bearing the
symbol, [QJ
EU RFPowerlEIRPj -227sdBmI2404MHz - 2480MHz)
caution
IThe max operating oFthe EUT is 4s"C and shouldn't be lowerthan
-IO"C
-23-
<GENERAL INFORMATION>
2.The device complies with RFspecifications when the device used
at Omm form your body.
3'oeclaration of Conformity.
We, Xiamen Huoshiquan Import & Export CO., L TD
hereby, declare mat the essential requiremems compliance with the
Directive 20 14/53/EU, the RoHS Direaive 20 I 1/65/EU and Safety
Directive 2009/48/EC have been fully fulfilled on our product with
indication below:
Product Name: Remme control four axis senes
Model/Mark HS210/HOLYSTONE
The Statement of compliance isavailable at the following address
http /WWN.holystone.com/docs/HS210_EU_DOC.pdf
This product can be usee across EU member states.
MANUFACTURER INFORMATION
Manufactured by
Xiamen Huoshiquan Import & Export CO_ LTD
Room 703,No. 813-2 )(Jahe Road, Simmg D1stnct XIAMEN, China
+ 11855) 88&6699
M2de in China
-24-