Holz-Blech Arboga I 40 User manual

× 50
× 15
× 470
× 50
× 30
5×70
4×506×1401,4X40
M8×70
Ø 3 mm
Ø 4 mm
Ø 5 mm
Ø 8 mm
× 130
4×40
1/24
ARBOGA I 40
PREPARE THE GROUND, UNWRAP THE PACKAGE,
LAY OUT THE COMPONENTS, FIND THE TOOLS.

2/24
ARBOGA I 40
MAKE SURE THAT THE FOUNDATION
IS INSTALLED ON A LEVEL SURFACE.
CHECKING ALL DIRECTIONS,
INCLUDING CORNER TO CORNER. 3%
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
IFB1
AC
D B
AB=CD
0°
IFB2
IFB3
IFB5
IFB4

× 2× 8
5×70
6×140
Ø 4 mm
Ø 5 mm
3/24
ARBOGA I 40
ATTACH FOUNDATION BEAMS
WITH SCREWS.
4%
6×140
5×70

4/24
ARBOGA I 40
LAY OUT THE BOTTOM LOGS SO,
THAT DOOR OPENING WILL BE
1441 MM WIDE
5%
2 LG-1
1 LG-5
A BL-1
B BL-1
1441 mm

× 4× 10
5×70
6×140
Ø 4 mm
Ø 5 mm
5/24
ARBOGA I 40
ATTACH LOGS TO THE
FOUNDATION.
THE WALL LOGS WILL HANG OVER
THE FOUNDATION BEAMS BY
APPROXIMATELY 5MM. THIS OVERHANG
IS DESIGNED AS A RAIN DRIP. 6%
6×140
5×70
5mm

× 3
5×70Ø 4 mm
× 4
6×140Ø 5 mm
6/24
ARBOGA I 40
7%
ATTACH THE NEXT ROW OF
WALL LOGS INTO THE BOTTOM
LOGS WITH SCREWS.
6×140 5×70
A LG-1
B LG-3

7/24
ARBOGA I 40
9%
AFTER PLACING 3-4 ROWS OF WALL LOGS, TAP EACH
WALL LOG IN PLACE USING A HAMMER AND THE
HITBLOCK PROVIDED, TO TIGHTEN THE LOGS.
HITBLOCK

8/24
ARBOGA I 40
10%
SLIDE THE DOOR IN,
ATTACH THE HANDLE.
CDD4
3 LOGS IN PLACE

9/24
ARBOGA I 40
22%
DON`T FORGET TO
TIGHTEN THE LOGS AFTER
EVERY 3-4 ROWS.
HITBLOCK
1 LG-6
1 LG-2
1 LG-1
B LG-2
B LG-1

10/24
ARBOGA I 40
SLIDE THE WINDOW IN,
ATTACH THE HANDLE.
23%
CW2L
CW2R

11/24
ARBOGA I 40
46%
2 LG-2
B LG-5
16 LOGS AND
1HALF LOG IN PLACE
B LG-4
1 LG-4
1 LG-7
1 LG-3

× 6
4×50
× 5
5×70
12/24
ARBOGA I 40
INSTALL CEILING TRIANGLE
AND ATTACH WITH SCREWS
INTO THE WALLS.
LEAVE 4CM CAP BETWEEN
DOOR AND CEILING DETAIL,
ATTACH IT INTO WALLS AND INTO
CEILING TRIANGLE USING SCREWS 47%
CEILING
DETAIL
40×120
CEILING
TRIANGLE
5×70
4×50

× 24
6×140Ø 5 mm
13/24
ARBOGA I 40
52%
ATTACH TOP LOGS INTO
WALL LOGS WITH SCREWS.
B TL-2
2 TL-3
2 TL-1
2 TL-2
A TL-3
A TL-1
A TL-2
A TL-4
1 TL-3
1 TL-1
1 TL-2
B TL-1
B TL-3
B TL-4

53%
CONNECT THE ROOF PURLINS (RFR)
WITH RD BEFORE INSTALLING THEM
ON TOP OF THE CORNERS. RD
RFR
14/24
ARBOGA I 40

55%
INSTALL THE ROOF PURLINS AND
ATTACH THEM WITH SCREWS.
× 4
6×140Ø 5 mm
15/24
ARBOGA I 40

× 8
5×70Ø 4 mm
× 8
6×140Ø 5 mm
16/24
ARBOGA I 40
58%
INSTALL THE ROOF PURLINS (RFB) AND
ATTACH THEM WITH SCREWS.
RFB2
RFB1
5×70
6×140

× 256
4×50
17/24
ARBOGA I 40
62%
PLACE THE FIRST ROOFBOARD FLUSH
WITH THE END OF THE PURLINS AND
ATTACH WITH SCREWS
RB16

ROOF TOP
× 32
4×40
18/24
ARBOGA I 40
86%
INSTALL THE ROOF TOP AND ATTACH IT
WITH SCREWS. ATTACH FASCIA TRIMS
INTO ROOFPURLINS.
RF

19/24
ARBOGA I 40
87%
SCREW THE FLOORBOARDS INTO
FOUNDATION, SAW THE
LAST BOARD TO MAKE IT FIT.
FB

20/24
ARBOGA I 40
96%
SAW THE BASEBOARDS
AND ATTACH WITH NAILS
AT EVERY 0,5 METERS.
× 30
1,4x40