Holz-Blech GNESTA 40 User manual

× 15
× 16
× 850
× 70
× 30
5×70
4×506×1401,4X40
M8×70
Ø 3 mm
Ø 4 mm
Ø 5 mm
Ø 8 mm
× 120
4×40
1/21
GNESTA 40
PREPARE THE GROUND, UNWRAP THE PACKAGE,
LAY OUT THE COMPONENTS, FIND THE TOOLS.

2/21
GNESTA 40
MAKE SURE THAT THE FOUNDATION
IS INSTALLED ON A LEVEL SURFACE.
CHECKING ALL DIRECTIONS,
INCLUDING CORNER TO CORNER. 3%
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
IFB1
AC
D B
AB=CD
0°
IFB2

× 18
6×140
3/21
GNESTA 40
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
4%

× 4× 10
5×70
6×140
Ø 4 mm
Ø 5 mm
4/21
GNESTA 40
LAY OUT THE BOTTOM LOGS,
ATTACH TO THE FOUNDATION.
THE WALL LOGS WILL HANG OVER
THE FOUNDATION BEAMS BY
APPROXIMATELY 5MM. THIS OVERHANG
IS DESIGNED AS A RAIN DRIP. 5%
2 BL-1
6×140
1 BL-1
1 BL-2
A LG-2
B LG-1
5×70
5mm

× 4
5×70Ø 4 mm
× 4
6×140Ø 5 mm
5/21
GNESTA 40
7%
ATTACH THE FIRST ROW OF
WALL LOGS INTO THE BOTTOM
LOGS WITH SCREWS.
2 LG-9
1 LG-2
1 LG-5
6×140
5×70

6/21
GNESTA 40
12%
AFTER PLACING 3-4 ROWS OF WALL LOGS, TAP EACH
WALL LOG IN PLACE USING A HAMMER AND THE
HITBLOCK PROVIDED, TO TIGHTEN THE LOGS.
HITBLOCK

7/21
GNESTA 40
13%
SLIDE THE DOOR IN,
ATTACH THE HANDLE.
CDD1
3 LOGS IN PLACE

8/21
GNESTA 40
26%
DON`T FORGET TO
TIGHTEN THE LOGS AFTER
EVERY 3-4 ROWS.
HITBLOCK
1 LG-2
A LG-1
1 LG-1

9/21
GNESTA 40
SLIDE THE WINDOW IN,
ATTACH THE HANDLE.
28%
CDW1
CW1R

× 8
6×140Ø 5 mm
10/21
GNESTA 40
42%
INSTALL THE GABLES WITH LONG SCREWS
TO THE WALL LOGS ON THE FRONT AND
REAR WALLS.
18 LOGS IN PLACE
GABLE2
GABLE2
GABLE1
A TL-1
B TL-1
GABLE 1

× 10
6×140Ø 5 mm
11/21
GNESTA 40
43%
INSTALL THE ROOF PURLINS AND
ROOF ELEMENTS 1, ATTACH THEM
WITH SCREWS.
RFR
RFR
RFR
RFB

× 475
4×50
12/21
GNESTA 40
84%
PLACE THE FIRST ROOFBOARD FLUSH WITH
THE END OF THE PURLINS AND ATTACH
WITH SCREWS. SAW THE LAST BOARD TO
MAKE IT FIT.
RB2
RB1

× 44
4×40
13/21
GNESTA 40
85%
FOR THE FASCIA TRIMS INSERT
SCREWS AFTER EVERY 0,5 METERS.
RR1
RR2

× 52
4×40Ø 3 mm
14/21
GNESTA 40
87%
EAVES EDGES GO ON TOP
OF THE ROOFING*.
*(NOT INCLUDED).
RF2
EE2

15/21
GNESTA 40
× 4
4×40Ø 3 mm
88%
ATTACH ROMBS WITH SCREWS.
ROMB

16/21
GNESTA 40
× 297
4×50Ø 3 mm
89%
18 SCREWS INTO THE FIRST FLOORBOARD,
9 INTO EACH NEXT, SAW THE
LAST BOARD TO MAKE IT FIT.

× 30
1,4x40
17/21
GNESTA 40
96%
SAW THE BASEBOARDS
AND ATTACH WITH NAILS
AT EVERY 0,5 METERS.
BB

× 16
M8×70
Ø 8 mm
18/21
GNESTA 40
97%
DRILL THROUGH THE WALL, HOLE MUST
BE AT THE BOTTOM OF THE OVAL,
ATTACH WITH BOLT.
4CM
20CM
WINDBOARD

90º
90º
19/21
GNESTA 40
98%
IF DOOR IS TILTED,
PUSH THE DOOR FRAME SO
THAT ALL CORNERS ARE 90º.

20/21
GNESTA 40
99%
IF DOORS ARE IN DIFFERENT HEIGHTS
OR THERE IS A GAP BETWEEN THEM,
ADJUST 3 SCREWS ON DOOR HINGES.