Holz-Blech Brantevik I 40 User manual

× 85
× 15
× 12
× 480
× 30
× 30
4×405×70
4×506×1401,4×40
M8×70
Ø 3 mm
Ø 4 mm
Ø 5 mm
Ø 8 mm
1/20
BRANTEVIK I 40
PREPARE THE GROUND, UNWRAP THE PACKAGE,
LAY OUT THE COMPONENTS, FIND THE TOOLS.

2/20
BRANTEVIK I 40
MAKE SURE THAT THE FOUNDATION
IS INSTALLED ON A LEVEL SURFACE.
CHECKING ALL DIRECTIONS,
INCLUDING CORNER TO CORNER. 3%
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
IFB
AC
D B
AB=CD
0°

× 6× 12
5×70
6×140
Ø 4 mm
Ø 5 mm
3/20
BRANTEVIK I 40
LAY OUT THE BOTTOM LOGS,
ATTACH TO THE FOUNDATION.
THE WALL LOGS WILL HANG OVER
THE FOUNDATION BEAMS BY
APPROXIMATELY 5MM. THIS OVERHANG
IS DESIGNED AS A RAIN DRIP. 5%
6×140
1 BL-1
1 BL-2
A LG-1
B LG-1
5×70
5mm
2 BL-1

× 4
5×70Ø 4 mm
× 6
6×140Ø 5 mm
4/20
BRANTEVIK I 40
7%
ATTACH THE FIRST ROW OF
WALL LOGS INTO THE BOTTOM
LOGS WITH SCREWS.
2 LG-6
1 LG-2
1 LG-5
6×140
5×70

5/20
BRANTEVIK I 40
12%
AFTER PLACING 3-4 ROWS OF WALL LOGS, TAP EACH
WALL LOG IN PLACE USING A HAMMER AND THE
HITBLOCK PROVIDED, TO TIGHTEN THE LOGS.
HITBLOCK

6/20
BRANTEVIK I 40
13%
SLIDE THE DOOR IN,
ATTACH THE HANDLE.
CDD1R
3 LOGS IN PLACE

7/20
BRANTEVIK I 40
26%
DON`T FORGET TO
TIGHTEN THE LOGS AFTER
EVERY 3-4 ROWS.
1 LG-2
1 LG-1

8/20
BRANTEVIK I 40
SLIDE THE WINDOW IN,
ATTACH THE HANDLE.
28%
CW1R

× 4
6×140Ø 5 mm
9/20
BRANTEVIK I 40
42%
INSTALL THE GABLES WITH LONG SCREWS
TO THE WALL LOGS ON THE FRONT AND
REAR WALLS.
14 LOGS IN PLACE
GABLE
B TL-1
A TL-1 B LG-4
B LG-3
B LG-2
A LG-2
A LG-3
A LG-4
14 LOGS IN PLACE

× 6
6×140Ø 5 mm
10/20
BRANTEVIK I 40
43%
INSTALL THE ROOF PURLINS AND
ATTACH THEM WITH SCREWS.
RFR
RFB
RFB

× 258
4×50
11/20
BRANTEVIK I 40
PLACE THE FIRST ROOFBOARD FLUSH WITH THE
END OF THE PURLINS AND ATTACH
WITH 6 SCREWS, 3 INTO EACH NEXT,
SAW THE LAST BOARD TO MAKE IT FIT.
46%
RB

× 40
4×40
12/20
BRANTEVIK I 40
79%
FOR THE FASCIA TRIMS INSERT
SCREWS AFTER EVERY 0,5 METERS.
RR1
RR2

× 32
4×40Ø 3 mm
13/20
BRANTEVIK I 40
83%
EAVES EDGES GO ON TOP
OF THE ROOFING*.
*(NOT INCLUDED) RF EE

×4
4×40Ø 3 mm
14/20
BRANTEVIK I 40
84%
ATTACH ROMBS WITH SCREWS.
ROMB

× 204
4×50
15/20
BRANTEVIK I 40
89%
14 SCREWS INTO THE FIRST FLOORBOARD,
7 INTO EACH NEXT, SAW THE
LAST BOARD TO MAKE IT FIT.
FB

× 30
1,4×40
16/20
BRANTEVIK I 40
96%
SAW THE BASEBOARDS
AND ATTACH WITH NAILS
AT EVERY 0,5 METERS.
BB

× 12
M8×70
Ø 8 mm
17/20
BRANTEVIK I 40
DRILL THROUGH THE WALL, HOLE
MUST BE AT THE BOTTOM OF THE OVAL,
ATTACH WITH BOLTS. 97%
WINDBOARD CONNECTS BOTTOM LOG
WITH THE TOP LOG. SAW THE WINDBOARD
INTO THE RIGHT LENGTH. FOR THE TOP
BOLT, DRILL 8MM HOLE THROUGH THE
WINDBOARD.
4CM
20CM
WINDBOARD

90º
90º
18/20
BRANTEVIK I 40
98%
IF DOOR IS TILTED,
PUSH THE DOOR FRAME SO
THAT ALL CORNERS ARE 90º.

19/20
BRANTEVIK I 40
99%
IF DOORS ARE IN DIFFERENT HEIGHTS
OR THERE IS A GAP BETWEEN THEM,
ADJUST 3 SCREWS ON DOOR HINGES.

20/20
BRANTEVIK I 40
WHEN THE HOUSE IS ASSEMBLED, YOU SHOULD
COVER THE TIMBER WITH WOOD PROTECTIVE SEAL,
PAINT OR STAIN AS SOON AS POSSIBLE TO AVOID
DETERIORATION TO THE WOOD.
100%