Home Concept LED101 Quick guide
-- PERFECT READING LAMP –Reading, hobbies, crafts
-- FULL SPECTRUM - Daylight Lamp bathes your page in
6400° Kelvin cool white light that closely mimics natural
sunlight
-- CRISP CLEAN LIGHT - Not just bright, but crisp, clean
light. Proven to improve contrast and reading ability
-- GLARE FREE - Softly diffused glare-free light. Perfect for
Aging Eyes!
-- ENERGY SAVING - wallet friendly, 12 watt LED lamp
delivers more concentrated light than a 100W
incandescent bulb.
-- DIMMABLE –New Touch sensor on head will dim down
to 10% power. Tap for on/off. Touch to dim.
-- SAFE - Does not get hot, so no burn worries for Kids or
Pets
No Fire Hazard
-- 100% MERCURY FREE!
-- LONG LIFE - 50,000 hour guarantee
-- BONUS - so close to sunlight that it doubles as a grow
light
Bright Reader
Natural Daylight LED Floor Lamp
by Home Concept
# LED101
IMPORTANT SAFETY INSTRUCTIONS
Read and Save:
1. Altering or modifying the lamp in any way will render
the product unsafe.
2. To prevent bad connections, avoid pulling
wiring connections when removing contents from
package, during installation, or in use.
3. This lamp is approved for indoor use only.
4. This equipment has been tested and found to comply
with the interference limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. If your lamp
causes interference to radio communications, try to:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the lamp and
receiver.
--Connect the equipment into an outlet on a circuit
different from the receiver.
BULB LIFE
Integrated LED bulbs last 50,000 hours and do not
require replacement. No user serviceable parts inside.
CLEANING AND MAINTENANCE
1. To clean: use a soft, dry cloth only.
2. Do not use chemical or abrasive cleaning solutions.
Assembly Instructions
NOTE : TAKE CARE NOT TO PINCH THE POWER CORD DURING ALL ASSEMBLY STEPS.
1. Take the FLEX POLE and feed the POWER CORD through the UPPER POLE.
2. Screw the UPPER POLE clockwise into the FLEX POLE.
3. Feed the POWER CORD through the MIDDLE POLE and screw MIDDLE POLE clockwise into the UPPER
POLE.
4. Feed the POWER CORD through the LOWER POLE and screw LOWER POLE clockwise into the MIDDLE
POLE. (lower pole has screw hole at bottom!)
5. Connect the two ends of the POWER CORD by pressing the LOCK CONNECTORS together.
6. Carefully feed the excess POWER CORD into the LOWER POLE. (Be careful not to pinch the cord!)
7. Turn and tighten the metal connecting COLLAR onto the base.
8. Remove the screw and insert the LOWER POLE into the COLLAR.
9. Check direction of the lamp and line up the screw holes and use a screwdriver to tighten the screw.
10. Plug the DC plug into the socket on the base.
11. Plug ADAPTER into outlet and now the lamp is ready for use.
Tips for Optional Performance
1. Your LED lamp offers instant-on, full power, so no need to let it “warm up”.
2. Gooseneck design lets you keep the lamp head below eye level so light shines on your work, not in your eyes.
3. TAP the touch sensor switch on lamp head to turn lamp on and off. TOUCH and HOLD your finger on sensor to
dim to your optimal brightness. When you tap it back on, your lamp will recall your last brightness setting!
4. The Bright Reader is a TASK lamp, designed for reading, sewing and handiwork. It is super-bright for tasks, but not
really designed to light-up an entire room or for ambient light.
5. Bonus: Bright Reader light is so close to sunlight that it makes a good grow light.
Product Questions:
sales@homeconcept.com
Watertown,WI 53094
Frequently Bought with the Bright Reader Floor Lamp
Bright Reader Desk Lamp #LED201BK or LED201GY Bright Reader Clamp-On Lamp #LED205BK
(Perfect for Stand up Desks)
Table of contents
