Home Decorators Collection AVONDALE WICKER FHWS80124 User manual

USE AND CARE GUIDE
AVONDALE WICKER RECTANGULAR LP FIRE PIT
Questions, problems, missing parts? Before returning to the store,
call Home Decorators Collection Customer Service.
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-800-986-3460
HOMEDEPOT.COM/HOMEDECORATORS
Item # 0000 000 000
Model # FHWS80124
THANK YOU
We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this fire table. We strive to continually
create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Home Decorators Collection!

2
Table of Contents
Table of Contents ............................. . . . . . . . 2
Safety Information .................... .. . . . . . .. . . . . . 2
Planning Assembly ........................ . . . . . . . . . 7
Hardware Included ................................. 8
Package Contents . .................................9
Care and Maintenance ....................... . . . . . . . . 20
Operation ................................. . . . . . . . . 14
Troubleshooting ............................ . . . . . . . . 21
Assembly. . . . . . ............................. . . . . . . . 10
Safety Information
READ ALL INSTRUCTIONS BEFORE USE. SAVE THESE INSTRUCTIONS.
WARNING: FOR OUTDOOR USE ONLY: (outside, non-enclosed area). Do Not Use For Cooking. Installation and service must be
performed by a qualied installer, service agency, or the gas supplier.
WARNING: FOR YOUR SAFETY: Do NOT store or use gasoline or other ammable vapors or liquids in the vicinity of this or any
other appliance. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING: FOR YOUR SAFETY: If the information in this manual is not followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life. Installation and service must be performed by a qualied installer, service
agency or gas supplier.
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.
If you are assembling this unit for someone else, give this manual to him or her to read and save for future reference.
DANGER: Do NOT leave this appliance unattended
while it is in operation.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause property
damage, injury or death. Read the installation,
operationg and maintenance instructions thoroughly
before installing or servicing this equipment.
FIRE OR EXPLOSION HAZARD
If you smell gas:
Failure to follow these instructions could result in fire or
explosion, which could cause property damage, personal
injury, or death.
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, leave the area immediately.
4. After leaving the area, call your gas supplier or
fire department.
DANGER
WARNING: Fuels used in liqueed propane gas
appliances, and the products of combustion of
such fuels, can expose you to chemicals including
benzene, which is known to the state of California
to cause cancer and cause birth defects or other
reprodctive harm.
For more information go to:
www.p65warnings.ca.gov.
CALIFORNIA PROPOSITION 65: Handling the brass
material on this product can expose you to lead, which
is known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands
after handling.
For more information go to www.P65Warnings.ca.gov.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
ANSI Z21.97-2017-/CSA 2.41-2017
Outdoor Decorative Gas Appliances
Warranty ............................ . . . . . . . . . . . . . . 7
Pre-Assembly ............................. . . . . . . . . . 7
Propane (LP) Dangers and Warnings ........... . . . . . . . . 5
Hose & Regulator Assembly and Replacement . . . . . . . . . . . 6
Glass Beads Warning ...................... . . . . . . . . . 6

3
WARNING: Fire table is for outdoor use only.
IMPORTANT NOTICE
IF YOU SMELL GAS
WARNING: Failure to follow the dangers, warning and cautions in this manual may result in serious bodily injury or death,
or in a fire or an explosion causing damage to property.
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Safety Information (continued)
Installation and repair should be done by a qualied service person. The appliance should be inspected before use and at least annually
by a qualied service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment,
burners and circulating air passageways of the appliance are kept clean.
Read and understand all warnings and precautions prior to assembly and use of your gas re table. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property damage.
The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54 or CAN/CGA-B149.1
Natural Gas and Propane Installation Code.
Minimum clearance from unit to combustible materials:
61 ft. (155.4 cm) from the top; 48 ft. (121.9 cm) from all sides and back. Do not locate this re table under any overhead enclosures.
Do not try lighting any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbors phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the re department.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing
ignition. Young children should be carefully supervised when they are in the area of the appliance. Clothing or other ammable
materials should not be hung from the appliance or placed on or near the appliance. Any guard, barrier, or other protective device
removed for servicing the appliance shall be replaced prior to operating the appliance.
Keep these instructions for future reference. If you are assembling this unit for someone else, give this manual to him or her to read
and keep for future reference.
This gas re table must be used ONLY outdoors in a well-ventilated space and shall NOT be used inside a building, garage, or
any other enclosed area.
DO NOT use this outdoor gas re table for indoor heating. TOXIC carbon monoxide fumes can accumulate and cause asphyxiation.
NEVER LEAVE this gas re table unattended when in use.
This unit is to be used with propane gas only! (sold separately)
Do not attach a remote gas supply to this unit.
Only use propane gas for this unit.
Converting this unit to natural gas is dangerous. This conversion kit shall be installed by a qualied service agency in accordance with
the manufacturer’s instructions and all applicable codes and requirements of the Authority having jurisdiction. The maximum inlet natural
gas pressure for this outdoor re table is 10 1/2 in. wc; the minimum inlet natural gas for this outdoor re table is 3 1/2 in wc.
Do not use a ame to check for gas leaks.
Do not store or use gasoline or other ammable vapors and liquids within 25 ft. (7.62 m) of this or any other appliance.
Do not store any combustible materials in the base enclosure.

The use of alcohol, prescription or non-prescription drugs may impair an individual’s ability to properly assemble or
safely operate this outdoor fire table.
DO NOT use this outdoor fire table under any overhead structure or near any unprotected combustible constructions.
DO NOT use in an explosive atmosphere. Keep gas fire table area clear and free from combustible materials, such as gasoline.
This outdoor fire table is not to be installed or used in or on recreational vehicles and/or boats.
Always use in accordance with all applicable local, provincial and national codes. Contact your local fire department for
details on outdoor burning.
Use the same precautions you would with any open fire when using this outdoor fire table.
DO NOT burn solid fuels such as: wood, charcoal briquettes, lump charcoal, manufactured logs, driftwood, trash, leaves, paper,
cardboard, plywood, or painted, stained or pressure-treated wood in this outdoor fire table.
DO NOT paint or color any part of this heating unit.
DO NOT use this outdoor fire table until it is COMPLETELY assembled and all parts are securely fastened and tightened.
DO NOT store another LP gas tank within 10 ft. (3.05 m) of this outdoor fire table while it is in operation.
DO NOT use this outdoor fire table near automobiles, trucks, vans or recreational vehicles.
Avoid using near or under overhanging trees and shrubs.
Always use this outdoor fire table on a hard, level, non-combustible surface such as concrete, rock or stone. An asphalt or
blacktop surface may not be acceptable for this purpose.
DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas control that has been under water.
DO NOT set the protective cover over the unit until it is turned off and completely cooled down.
DO NOT use in windy conditions.
Keep all electrical cords away from a hot outdoor fire table.
Certain areas of this outdoor fire table when in use will become too hot to touch. Do not touch hot surfaces until the unit has
cooled unless you are wearing protective gear such as insulated pot holders or heat-resistant gloves or mittens to avoid burns.
DO NOT attempt to move or store this outdoor fire table until all parts are cool.
DO NOT lean over this outdoor fire table when lighting or when in use.
Use only the regulator and hose assembly provided. The replacement regulator and hose assembly shall be that specified
by the manufacturer.
DO NOT attempt to disconnect the gas regulator from the tank or any gas fitting while the outdoor fire table is in use.
Always shut off the supply at the tank valve and disconnect regulator from the tank when the fire table is not in use.
DO NOT sit on the fire table when the unit is in operation.
DO NOT throw anything onto the fire when the unit is in operation.
Glass beads are very hot; please keep children and pets at a safe distance.
It is essential to keep the outdoor fire table valve compartment, burners, and circulating air passages clean. Inspect outdoor
fire table before each use.
Check for leaks after not using the unit for long periods of time.
Prior to each fire table operation, check the hose for evidence of excessive abrasion or wear by looking through the visual check
hole. If the hose is damaged, cracked or cut, it must be replaced before using the gas fire table. The hose assembly can only be
replaced with a hose assembly specified by the manufacturer. Please call the service center at 1-800-986-3460.
Before each use, remove the glass beads. Examine the burner and its components. If dirty, clean with a soft brush and soapy water
solution. Also examine the area around the burner. Any dirt or foreign material, such as spider webs or nests in this area, should be
removed. If it is evident that the burner is damaged, the fire table must not be used. The burner assembly cannot be replaced. Please
contact the service center at 1-800-986-3460 for technical support.
Place the hose out of the pathways where people may trip over it (if using external tank). Do not place the hose in areas where it
may be subjected to accidental damage.
Safety Information (continued)
4

Safety Information (continued)
PROPANE (LP) DANGERS AND WARNINGS
ATTENTION: Any alteration of the outdoor fire table that is not specifically directed in the operations manual will void manufacturer warranty.
LP GAS
LP gas is flammable and hazardous if handled improperly. Familiarize yourself with its hazards before using any LP gas product.
PROPANE HAZARDS
Flammable, explosive under pressure, heavier than air and settles in pools in low areas.
In its natural state, propane has no odor. For your safety, an odorant has been added.
Contact with propane could burn your skin.
Propane is extremely flammable and hazardous if handled improperly.
LP GAS WARNINGS
Cylinders must be stored outdoors in a well-ventilated area out of reach of children.
Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage or
any other enclosed area.
Never use a propane cylinder with a damaged body, valve, collar or footing.
Dented or rusted propane cylinders may be hazardous and should be checked by your propane gas supplier.
Be sure to use only one 20 lb (9.1 kg) LP gas cylinder with a Type 1 valve with this appliance as required by the American
National Standards Institute (ANSI) and the Canadian Standards Steering Committee.
Only tanks marked “propane” may be used.
The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, or
CAN/CGA-B149.1, Natural Gas and Propane Installation Code.
LP gas tank must be arranged for vapor withdrawal.
The LP gas tank must have a listed overfilling prevention device (OPD) and a QCCI Type I (CGA810) LP gas tank connection.
The LP gas tank must have a tank collar to protect the tank valve.
Never use an LP gas tank with a damaged body, valve, collar, or footing. Dented or rusted LP gas tanks may be hazardous.
The LP gas tank should not be dropped or handled roughly.
Tanks must be stored outdoors out of the reach of children. Do NOT store in a building, garage, or any other enclosed area.
Never store your LP gas tank where temperatures can reach over 125°F (52°C).
Do not store the LP gas cylinder in direct sunlight or near a source of heat or combustion.
Never keep a filled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to increase, which may open the
relief valve and allow gas to escape.
Place dust cap on valve outlet whenever the LP gas tank is not in use. Only install the recommended type of dust cap on the
LP gas tank and the LP gas tank valve. Other types of caps or plugs may result in leakage of propane.
Do not store a spare LP gas cylinder under or near this appliance.
Never fill the LP gas cylinder beyond 80% full.
If the information in (a) and (b) is not followed exactly, a fire causing death or serious injury may occur.
LP gas cylinders should be filled only by a certified LP gas dealer.
The pressure regulator is set for 11 in. wc (2.74 kPa).
The maximum inlet propane gas pressure for this outdoor fire table is 250 PSI; the minimun inlet propane gas pressure for this
outdoor fire table is 25 PSI.
The maximum inlet natural gas pressure for this outdoor re table is 10.5 in. wc.
The minimum inlet natural gas pressure for this outdoor re table is 3.5 in. wc.
Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer, motor home or house.
Always use the pressure regulator and hose assembly provided with the appliance to connect to a LP gas cylinder. Never connect
to an unregulated LP gas supply. For technical support contact the service center at 1-800-986-3460.
Hand turn the manual gas control valve. Never use tools. If the valve will not turn by hand, do not try to repair it. Call a certified
gas technician. The use of force or any self-attempted repair may result in a fire or explosion.
When Connecting Your Gas Cylinder
Before connecting, be sure that there is no debris caught in the head of the gas cylinder, head of the regulator valve or in the ports.
Connect regulator valve and hand-tighten firmly. Disconnect the propane cylinder from the regulator valve when the fire table is
not in use. DO NOT obstruct the flow of combustion air and ventilation air to the burner.
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
5
Constructed and marked in accordance with the U.S. Department of Transportation (D.O.T.) Specifications for LP-Gas Cylinders,or
the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable.

HOSE AND REGULATOR ASSEMBLY AND REPLACEMENT
This fire table comes equipped with a standard LP gas hose and regulator including the appliance side connection for a CGA
No. 791 Cylinder Connection Device. The LP gas hose and regulator supplied with this fire table must be used. Only a hose and
regulator specified by manufacturer can be used for replacement.
The CGA No. 791 connection incorporates a magnetic flow limiting device that acts to limit the flow of gas if a leak is
detected between the regulator and the burner valve.
If the burner valve is open prior to the LP gas cylinder service valve being opened, the connection will interpret this
free flow of gas to be a leak.
The connection safety feature will reduce gas flow from the regulator to the appliance to a minimal level.
Be sure that the burner control valve is closed prior to opening the LP gas cylinder service valve to ensure that the
connection flow limiting device is not triggered mistakenly.
If the connection flow limiting device is triggered mistakenly, close the LP gas cylinder service valve and the burner
valve, wait 10 seconds to allow the device to reset, open the cylinder service valve, then open the burner valve and light
the fire table as per lighting instructions.
Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose contacts any hot surface.
Regular maintenance of the hose and regulator:
Inspect the hose before each use of the fire table. If the hose shows signs of cracks, abrasions, cuts or damage of any
kind, do not operate the appliance. Fix or replace the hose as required before using the appliance. For assistance with
repair or replacement of the hose, call the service center at 1-800-986-3460. Use only replacement parts from the
manufacturer.
Inspect the seal inside the CGA No. 791 service valve on the LP gas cylinder when replacing the cylinder or at least once
per year. If there is any indication of damage, have the seal replaced by a certified gas dealer before operating
the appliance.
Do not use tools to tighten the CGA No. 791 connection nut onto the LP gas cylinder service valve. Hand tighten only.
Be careful to not cross the threads on the connection when tightening the CGA No. 791 connection onto the LP gas cylinder
service valve.
A leak test should always be performed after attaching the connection to LP gas cylinder service valve. See Step 5, “Tank/Gas Line
connection Leak Test”, in the “Operation” section of this manual.
For connection instructions, see Steps 1–2 in the "Operation" section of this manual.
GLASS BEADS WARNING
Glass beads may have sharp edges. Wear safety glasses and gloves when handling.
If changing or substituting the glass beads with other media, use lava rocks/pumice stones/glass shards/glass beads available
from your local authorized dealer/distributor.
Pour the glass beads evenly into the burner area (with the exception of the screen, if applicable). The glass beads should be 1/2 to
1 in. (1.2 to 2.5 cm) above the burner.
Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks/pumice stones/glass
beads could pop out and cause injury. Should any rocks pop out, discard them.
Always ensure that lava rocks/pumice stones/glass shards/glass beads are completely dry before use. Failure to do so will
cause them to crack or pop.
Safety Information (continued)
6
DO NOT PLACE ANY
MEDIA ON SCREEN
CAUTION: Do not exceed a height of 1 in. (2.5 cm) above the burner when placing glass beads or other media.
Ensure no media covers the igniter screen. Store any excess glass beads in a safe location.

Warranty
Pre-assembly
PLANNING ASSEMBLY
Read all instructions before assembly.
To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
NOTE: More than one person may be required to assemble this product.
1 YEAR FRAME LIMITED WARRANTY
WHAT IS COVERED
We warrant the frames to be free of manufacturing defects to the original purchaser for one year.
WHAT IS NOT COVERED
It remains the customer’s responsibility for freight and packaging charges to and from our service center. This warranty does not cover
We reserve the right to make substitutions with similar merchandise, if the model in question is no longer in production.
Contact the Customer Service Team at 1-800-986-3460 or visit HOMEDEPOT.COM/HOMEDECORATORS.
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
7
commercial use, hardware, acts of nature, re, freezing and abusive use. In addition, purchased parts are not covered under this warranty.

Pre-assembly (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
AA BB CC DD
EE FF GG
M6x15 Combination Bolt
M6x40 Combination Bolt
14+1
4+1
AA
BB
M6x12 Countersunk Bolt 1+1
CC
M4x30 Bolt 1+1
DD
Plastic Washer 1 1+1
EE
Plastic Washer 2 1+1
FF
Hex Wrench 1
GG
Part Description Quantity
8

Burner Lid
Table Top
Left SidePanel
1
1
A
B
1 C
Right Side Panel
Door
Back Panel
1
1
D
E
1 F
Tank Support
Limit Tube
Glass Beads
1
1
G
H
1 I
AAA Battery
Rectangular Burner Bowl
Burner Ring
1
1
J
K
1 L
Pilot Housing
Manual Electric Igniter
Control Knob
1
1
M
N
1 O
Regulator/Hose 1
P
Knob 1
Q
Part Description Quantity WARNING: Failure to position the parts in
accordance with these diagrams or failure to
use only parts specically approved with this
appliance may result in property damage or
personal injury.
Pre-assembly (continued)
PACKAGE CONTENTS
9
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
I
A
MB
F
P
H
O
N
C
LK
J
G
Q
E
D

Assembly
1Attaching the Left Side Panel and Right Side Panel to the Table Top
2Attaching the Back Panel to the Left Side Panel and Right Side Panel
Place the table top (B) upside down on a soft surface.
Do not tighten the bolts at this step.
Attach the left side panel (C) and right side panel (D) to the table top (B) using M6x15 combination bolts (AA), as shown below.
Attach the back panel (F) to the left side panel (C) and right side panel (D) using M6x40 combination bolts (BB).
Do not tighten the bolts at this step.
NOTE: Pay attention to the direction of control knob and the legs. They must be placed as the step shows.
10
NOTE: Loosely tighten all the bolts using hex wrench (GG).
NOTE: Loosely tighten all the bolts using hex wrench (GG).
AA
C
D
B
BB
F
D
C

Assembly (continued)
3Attaching the Limit Tube to the Left Side Panel and Right Side Panel
4Connecting the Tank Support
Attach the limit tube (H) to the left side panel (C) and right side panel (D) using M6x15 combination bolts (AA), as shown below.
Do not tighten the bolts at this step.
Connect the tank support (G) to the left side panel (C) and right side panel (D) using M6x15 combination bolts (AA).
Once all of the bolts are in place, fully tighten all the bolts using the hex wrench (GG).
11
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
NOTE: Loosely tighten all the bolts using hex wrench (GG).
D
AA
H
C
AA
F
G
C
D

Assembly (continued)
5Connecting the Door
6Attaching the Knob to the Door and Checking the Table
Connect the door (E) to the left side panel (C) using M6x12 countersunk bolt (CC) and plastic washers 1 (EE), as shown below.
Turn the re table right side up.
Connect the door (E) to the tank support (G) using plastic washers 2 (FF), as shown below.
Tighten the bolts at this step.
Attach the knob (Q) to the door (E) using M4x30 bolt (DD).
Ensure all connections are secure before use.
12
EE
CC
C
FF
GE
Q
DD
E

Assembly (continued)
7Placing the Glass Beads
8Placing the Burner Lid
Place the glass beads (I) into the rectangular burner bowl (K).
Place the burner lid (A) over the rectangular burner bowl (K).
Make sure to remove the burner lid before lighting.
Do not place the lid back onto the rectangular burner bowl until it has cooled down.
13
WARNING:
K
I
A
K
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
CAUTION: To ensure proper function, the screen on the pilot housing should be free of glass beads.
Screen
CORRECT INCORRECT
Pilot
Housing
Burner
Tube
do not block
opening
Surfaces on the re table can remain extremely hot for a period after use.
Allow 45 minutes to cool down before touching or moving the re table.

Operation
1
Loosen LP gas tank retainer bolt by turning counterclockwise.
Secure tank by turning LP gas tank retainer bolt clockwise until tight.
CAUTION: Make sure LP gas tank valve is closed.
14
Installing the LP Gas Tank
2Connecting the LP Gas Tank
Before connecting, be sure there is no debris caught in the head of the LP gas tank, in the head of the regulator valve
or in the head of the burner ports.
Connect the regulator/hose assembly to tank by turning knob clockwise until it stops.
The LP gas tank must be properly disconnected and removed prior to moving this outdoor re table.
To operate, you will need one precision-lled standard grill LP gas tank with external valve threads.
Place precision-lled LP gas tank upright into hole in outdoor re table base so the tank valve is facing the gas line connection.

3Disconnecting the LP Gas Tank
Before disconnecting make sure the LP gas tank valve is “CLOSED”.
Disconnect regulator/hose assembly from LP gas by turning knob conterclockwise until it is loose.
Place the protective cap cover on the LP gas tank and store it outdoors in a well-ventilated area out of direct sunlight.
15
Operation (continued)
NOTE:
4Checking for Leaks and Burner Connections
“Safety Information” section on pages 2 to 6.
Failure to follow those instructions can cause serious injury, damage to property or result in death.
Make sure the regulator/hose and valve connections are securely fastened to the burner and the tank.
CAUTION:
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Failure to inspect this connection or follow these instructions could cause a re or
an explosion which can cause death, serious bodily injury or damage to property.
The LP gas tank must be properly disconnected and removed prior to moving this re table.
Before using this outdoor re table, make sure you have read, understood and are following all information provided in the
Visually check the connection between the burner/venturi tube and orice.
Make sure the burner/venturi tune ts over the orice.

Figure 1 Figure 2
5Tank/Gas Line Connection Leak Test
Make 2-3 oz. of leak detection solution by mixing one part liquid dishwashing soap with three parts water.
Make sure the control knob is in the “OFF” position.
Connect LP gas tank per “CONNECTING LP GAS TANK” section.
Turn LP gas tank valve to “OPEN”.
Using a spoon or a squirt bottle, pour several drops of solution over each spot marked “X.”
a. If any bubbles appear, turn LP gas tank valve to “CLOSED”, reconnect and re-test.
b. If you continue to see bubbles after several attempts, turn LP gas tank valve to “CLOSED” and disconnect LP gas tank,
per “DISCONNECTING LP GAS TANK”.
c. If no bubbles appear after one minute, turn LP gas tank valve to “CLOSED”, wipe away solution and proceed.
16
Operation (continued)
6Inserting the Battery and Control Knob
Insert the AAA battery (J) into the manual electric igniter (N) and twist the button cover on to igniter housing.
Do not overtighten.
CAUTION:
J
N
Do not put batteries into the re or trash. Please treat batteries as hazardous waste and recycle properly.
X
XX
XX

Close the door (E). Now the re table is complete and ready to use.
7Closing the Door
17
Operation (continued)
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
E

WARNING:
CAUTION:
CAUTION:
CAUTION:
Operation (continued)
LIGHTING
Make sure all labels, packaging and protective lms have been removed from the outdoor re table.
Remove cover and burner lid (if applicable) before operating re table. Check for obstructions of airow to the burner.
Spiders, insects and webs can clog the burner/venturi tube. A clogged burner tube can lead to a re.
Control knob must be in the “OFF” position.
To ensure proper function, the screen on the pilot housing should not be covered by glass beads.
Connect LP gas tank per steps 1 and 2 in the "Operation" section.
Turn LP gas tank valve to “OPEN”.
Push and hold the ame ignitor to create sparks within the electrode; and continue to hold.
Push in the control knob and turn to the “ON” position. Keep holding down the control knob to allow gas to ow for 20 seconds.
After 20 seconds, release and turn control knob counterclockwise to adjust ame to desired height.
If ignition does not occur in 20 seconds turn burner control knob to “OFF”, wait ve minutes, fan with a newspaper or
magazine, and repeat lighting procedure.
18
CAUTION: Failure to follow these instructions
could cause a fire or an explosion which can cause
death, serious bodily injury or damage to property.
Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a re.
Never light burner with the cover on the outdoor re table.
Do NOT obstruct ow of combustion and ventilation air.
Keep outdoor gas appliance area clear and free from combustible materials, gasoline and other
ammable vapors and liquids.
9.84–11.81 in.
25–30 cm.
Proper flame height
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

19
Operation (continued)
LIGHTING (CONTINUED)
If igniter does not light burner:
a. Wearing heat-resistant gloves, position a long, lit match or long, lit butane lighter near the pilot housing.
b. Push and turn control knob to “ON”.
c. Remove match/lighter once burner is lit.
After lighting, observe the burner flame and make sure all burner ports are lit and flame height matches illustration on page 18.
newspaper or magazine, and repeat lighting procedure.
Turning Off
Turn LP gas tank valve to “CLOSED”.
Turn control knob to the “OFF” position.
Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
Notices
This outdoor fire table should be thoroughly cleaned and inspected on a regular basis.
Abrasive cleaners will damage this product.
NEVER use oven cleaner to clean any part of this outdoor fire table.
Before Each Use
Ensure the outdoor re table area is clear and free from any combustible materials, gasoline and other
ammable vapors and liquids.
Do not obstruct the ow of the combustion of LP gas and the ventilation of air.
Keep the ventilation opening(s) of the LP gas tank area free and clear of debris.
Visually check the burner ames to make sure your outdoor re table is working properly.
See below for proper cleaning instructions.
Check all gas connections for leaks.
Check components for any signs of damage or rust.
Check for obstructions of airow to the burner. Spiders, insects and webs can clog the burner/venturi tube. A clogged
burner/venturi tube can lead to a re.
If damage to any component is detected, do NOT operate until repairs are completed.
NOTE: A “poof” sound is normal as
the last of the LP gas is burned.
CAUTION: NEVER place cover on hot
outdoor re table.
CAUTION: If ignition does not occur in 5 seconds, turn control knob to “OFF”, wait 5 minutes, fan with a
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
11.
1.
2.
3.
12.

20
Care and Maintenance
Cleaning Surfaces
Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water.
For stubborn stains, use a citrus-based cleaner and a nylon scrubbing brush.
Rinse clean with water.
Allow to air dry.
Before Storing
Turn LP gas tank valve to “CLOSED”.
Turn control knob to the “OFF” position.
Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
Clean all surfaces.
Lightly coat the burner with cooking oil to prevent excess rusting. NEVER place cover on hot outdoor fire table.
If storing the outdoor fire table indoors, cover the outdoor fire table and store in a cool, dry location away from children and pets.
If storing the outdoor re table outdoors, cover the outdoor re table to protect from the weather.
Replacement Parts
For replacement parts, call our service center at 1-800-986-3460.
Cleaning and Care
NOTE: A “poof” sound is normal as
the last of the LP gas is burned.
CAUTION: Do not clean any outdoor fire table part in a self-cleaning oven. The extreme heat will damage the finish.
CAUTION: Do not enlarge valve orifices or burner ports when cleaning the valves or burners.
CAUTION: All cleaning and maintenance should be done when outdoor fire table is cool and with the fuel supply disconnected.
CAUTION: Cover your fire table when not in use to protect it from the elements. We recommend that your fire table be
stored indoors during the winter months. It will protect it from cracking in extreme cold. If it must be stored outside, it
should ALWAYS be covered.