Home Decorators 24 in. Base Cabinet User manual

1
STEP 3
wall prep
Tape measure
Pencil
Level
Stud Finder
Hammer
Screw Driver #2 Flat Head and #2 Phillips
#10 x 3" Pan Head Screws
#8 x 1¼" Pan Head Screws
Cordless Drill – to pre-drill cabinets and mount
to wall and to each other
3
/ 16", 3 / 32" Drill bits
Hacksaw – to cut 48" Closet Rods to size (if needed)
Circular Saw – to cut 48" Furniture shelves to size
(if needed)
Toggle bolts - if you are unable to hit a stud behind
the drywall
1. Before you begin, make sure that your wall is smooth and plumb – remove any obstructions such as old closet
organizers, cabinets or baseboards that may interfere with the installation.
2. By using your tape measure and level mark the locations of your base cabinets on the wall. Plan accordingly to
make sure drawers will open fully without obstruction!
3. Use your stud nder to locate the studs in your wall – mark either side of the stud and the center point, to show
where you need to hit with your installation screws. If necessary adjust the location of you cabinets slightly to
enable you to hit the required studs easily.
INSTALLATION STEPS FOR WALLS WITH WOOD STUDS
STEP 3ASTEP 2
Before you begin, please read this manual completely so
that you will have a good understanding of the sequence
of events.
Please follow all the safety instructions for tools
and procedures.
Note: Attachment to any
other surface material such
as metal studs, concrete
block, brick, stucco or
poured concrete require
special fasteners. Consult
with your local Home Depot
store or installation specialist
for recommended fasteners.
Got questions?
Customer Service:
1-866-373-9131
Monday - Saturday
9:00AM - 6:00PM EST
Email us at:
[email protected]
Closet Cabinet
Installation Guide
TOOLS & MATERIALS REQUIRED

24 in.
Base Cabinet
installation
4. Before you start, make sure the cabinets are empty.
5. Measure the distance from the outer edge of the rst base cabinet to the center of the studs you wish to attach to.
6. Transfer these measurements to the horizontal installation rail, along the back of the base cabinet.
7. Drill pilot holes thru the horizontal installation rail with a 3/32" drill bit. NOTE: If you can only hit one stud, use a drywall toggle bolt to
create a second attachment point (consult your local Home Depot store for the correct toggle for your wall construction).
**BASE CABINETS MUST HAVE TWO ATTACHMENT POINTS!
8. Attach base cabinet thru the drywall and into the studs using #10 x 3" pan head screws. Check that it’s level and shim if necessary.
(DO NOT FULLY TIGHTEN! Double check for shim and level and adjust if needed).
9. Using a 3/32” bit, drill (3) attachment pilot holes in the top of the Base Cabinet if you are placing a Wall Cabinet on top. Drill one hole on
the left and right side, near the front edge. Drill one hole, centered near the back, .
STEP 6STEP 5 STEP 7
STEP 8A STEP 8B STEP 9
B

3
24 in.
Wall Cabinet
installation
1. Place the Wall Cabinet on the Base Cabinet and mark the sides and top of the Wall Cabinet on the drywall,
remove the Wall Cabinet.
2. Locate your stud markings on the wall and mark the center of each stud approximately 3" from the top and bottom of the Wall
Cabinet placement.
3. Transfer these measurements to the two horizontal installation rails, along the back of the Wall Cabinet at top and bottom.
4. Drill (4) mounting holes thru the installation rails top and bottom of wall cabinet with a 3/32" drill bit.
STEP 5 STEP 6 STEP 7
STEP 3 STEP 4
NOTE: If you can only nd one stud, use
a drywall toggle bolt to create a second
attachment point. (Consult your local
Home Depot store for the correct toggle
for your wall construction).
**WALL CABINET MUST HAVE
FOUR ATTACHMENT POINTS!
5. Now place the wall cabinet on top of the base cabinet. Align and level – hold in place with “Quick Grips” or C-clamps.
6. Attach Base Cabinet to Wall Cabinet thru the pilot hole, using #8 x 1¼" pan head screws.
7. Attach the Wall Cabinet thru the drywall and into the wood studs using #10 x 3" pan head screws or install drywall
toggle bolt if necessary - DO NOT FULLY TIGHTEN! Check the level and adjust as needed. Once you are happy with
the alignment and level of the two cabinets, fully tighten all the attachment screws.
A

48 in.
Closet Shelf
and Rod
installation
1. The two mounting rails with the 48 in. Shelf can be installed to the outside of the cabinets, or directly to the drywall of the
closet space.
The mounting rails have two specic purposes:
a. They are pre-drilled to accept the Closet Rod Brackets which hold the closet rod in place
b. They also support the 48 in. Shelf above the Closet Rod
2. Decide on the location of your Closet Shelf. If you want it to align with the top of the wall cabinet, set the Mounting Rails ¾" down
from the top edge of the wall cabinet (as shown).
3. Use a level to mark a line where the top edge of the Mounting Rail will be located. Pre-drill two holes thru the side of the adjacent
cabinet to attach the Mounting Rail.
4. With the pre-drilled holes through the cabinet, attach the Mounting Rails using (2) #8 x 1¼" pan head screws provided.
5. Alternatively, mark the location of the second Mounting Rail on the side drywall of the closet space, and drill two attachment holes
thru the Mounting Rail using 3/32" drill bit. Place the Mounting Rail on the drywall and mark the attachment points on the wall. If you
are installing the second Mounting Rail into another cabinet, simply repeat Step 2-4.
6. Screw the Mounting Rail in place using a suitable drywall fastener (consult your local Home Depot store for the proper Screws and
anchors for your wall construction)
7. Once the Mounting Rails are installed, you can set your Shelf and attach the Closet Rod Brackets (optional).
8. Cut the Closet Rod with a hacksaw, to t the Closet Rod Brackets.
STEP 3 STEP 5-6 STEP 7
DRAWER FRONT ADJUSTMENT
If additional adjustment is required,
loosen screws and twist drawer front
for proper alignment. Tighten screws
securely.
NOTE: ADJUST DRAWER
FRONT BEFORE INSTALLING
DECORATIVE HARDWARE!
Attaching
decorative
hardware
Do not drill holes until you have determined the dimensions match the decorative
hardware you have selected. Make sure any drawer fronts alignments are done
prior to drilling them for pulls or knobs - once the decorative hardware is installed it
will be difcult to adjust the drawer fronts.
1. Clamp a piece of wood to the front side of the drawer front, at handle location
2. From the inside of the drawer use a 3/16" drill bit and be sure to drill
completely through the drawer front into the block this allow for a clear hole.
Push the bolt through the hole and apply the hardware. Tighten with
a screwdriver.
STEP 8