Home Zone Security ES06462V User manual

104W Dual Head AC LED Work Light
Model No. ES06462V
[phone]
IMPORTANT SAFETY OPERATING INSTRUCTIONS
1. Please read all warning and instruction labels which are included in the box and fixture to avoid personal injury, property damage
caused by fire, cuts, bruises, death and other dangers.
2. Please follow these general precautions before installing, maintaining, or fixing
1. Before connecting to the power outlet make sure that the voltage indicated on the rating label is compatible with the supply voltage
2. This item is damp rated. NEVER submerge this product in water.
3. Do not use on hot surfaces.
4. Do not remove the lens protecting the LED
5. Do not use in areas near a gas source
6. It is NOT possible to change the LED light source
7. This light is not intended for use in potentially explosive environments. This is NOT a vapor proof light
8. Under wet or damp conditions, use only GFCI protected circuits
9. Place the electrical cord away from busy areas to avoid accidental tripping and contact
10. Place your light on a stable and level surface to avoid tipping or being knocked over accidentally
1. When using product, basic precautions should always be followed
2. To avoid RISK of electrical shock, ALWAYS turn off or disconnect from power while installing or servicing
unit
3. Always insert or remove plug from the outlet by grabbing the plug by hand. Do not pull on the power cord
4. Do not look directly at the LED lights for any length of time.
5. Carefully read and understand the information given in this manual before beginning installation. Failure to
do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal
6. This light fixture is NOT A TOY and is not suitable for use by children.
7. We do not take responsibility if the instruction manual is not followed correctly or if the product is handled
improperly resulting in damage to person or property
PRECAUTION
1. AC120V 60Hz
2. Watts: 2 x52W
3. Brightness: 10000lumens
4. Color temperature: 5000K
REF. PARTS
PARAMETER:
securit y
www.homezonesecurity.com
Light fixture Tripod stand Bracket Handle Flash light

Model No. ES06462V
104W Dual Head AC LED Work Light
[phone]
INSTALLATION AND OPERATION
To install:
Loosen locking knob and pull legs away from the center pole until all legs are fully
extended. Retighten locking knob firmly.
Note: it is possible to utilize tripod without legs fully extended, as long as all 3
outer legs touch the ground, however full extention is highly recommended for
maximum security and sturdiness
Attach Handle to Bracket using (2) plastic mounting knobs (Pre-installed on the
Bracket)
Figure2:
Attach light head fixtures to Bracket using (2) mounting knobs (Pre-installed on the
Bracket)
Figure4:
Attach the power cord to Handle with the screw pre-installed on the handle
Figure5:
Unlock locking collars by twisting counter clockwise. Lift the pole up to desired
height. Twist clockwise to relock locking collar.
Figure6:
Attach Bracket to tripod by pinching red buttons in. Align holes on the underside
of the light bar with locking tabs on tripod stand. Release red tabs to lock
Note: Make sure the bracket is connected completely to the locking tabs on the
tripod stand. Lift the handle to confirm. Failure to complete this step may cause
injury or damage to the lights
Figure3:
securit y
www.homezonesecurity.com

Model No. ES06462V
[phone]
securit y
www.homezonesecurity.com
104W Dual Head AC LED Work Light
To operate:
1. Plug AC cord into AC outlet
2. Use power switch on the back of the light fixtures to turn on the light
3. Tilt and adjust to any angle for best light
4. Tighten knobs to secure work light to desired angle
Note: NEVER submerge this product or power cord in water
Work light:
Flash light:
Insert 3 x 1.5V AA
batteries into the
battery compartment
and mak sure the
polarity is correct
Use the rotatable swivel
hook to hang the flashlight
for convenience.
Attach to metal surfaces
using the built-in base
magnets
• Press the power button to turn on
top flashlight
• Press the power button a second
time to turn on inspection light
• Press the power button a third time
to power off