Homebase 572392 User manual

INSTRUCTION MANUAL
99CM LED SPUN
ACRYLIC TREE
IMPORTANT: Please read these instructions before using the product and retain for future use.
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576

Caution
• For indoor or outdoor use. Always place the plug into an indoor mains socket or a weatherproof outdoor socket.
• Always unwind the cord before use. Do not connect the product to the power supply whilst the product is still in the packaging.
• This light set is constructed with non-replaceable LED bulbs. DO NOT attempt to replace any of the LED bulbs in the light set.
• This product is intended for occasional decoration only; not to be used by children as a toy, and not intended for household illumination.
• It is normal for the transformer to run a little warm. Please ensure it's used in a well ventilated area.
• Keep away from sources of heat and naked flames.
• Unplug when not in use.
• Always unplug from the mains supply whilst installing, carrying out maintenance or adjustments.
• The external flexible cable or cord of this light set cannot be replaced; if the cord is damaged, the light set must be destroyed.
• Use only with the supplied transformer.
• When storing away, make sure the area is dry. Avoid any damp, wet and humid areas.
• Please read these instructions carefully. Keep these instructions in a safe place for future reference.
Product specifications
• Rated input: 32V AC Max. 3.6W
• Bulb rating: 3.2V 0.064W
• Transformer: JT-EL/FC32V3.6W-H6
Before you start
1. Study the ‘Caution’ section carefully.
2. Decide on an appropriate location for your product. Make sure that you have plenty of space, a level surface, and a clear dry area for
assembly, then locate. Always try to assemble the product as close as possible to the intended location.
3. Check the pack and make sure you have all of the parts.
4. Remove all plastic packaging material and dispose of them safely.
No. Parts list Qty
1
2
3
4
Upper part of tree
Lower part of tree
Ground stake
Power transformer
1
1
4
1
Assembly
Step 1 Step 2 Step 3
Connect the upper part of the tree (1)
to the lower part of the tree (2). Insert
the two iron wires at the bottom of the
upper part of the tree (1) into the nut
holes of the lower part of the tree (2).
Fasten together the upper part of the
tree (1) and the lower part of the tree (2).
Rotate the C buckle on the upper part
of the tree outwards, then press the
wire under the tree to tighten it.
Assembly complete. If you
position outdoors, please use
the stakes (3) provided and fix
them into the ground.
Parts list
76cm
99cm
20cm
Assembled dimensions

Operating instructions
1. Unpack the product from the box.
to be collected and recycled at end of life. Users of
separate collection facilities available.
aged to minimise any potential effects on the
Disposal and recycling
Electrical products are labelled with the wheelie bin symbol to indicate that they are
electrical products should not dispose of them as unsorted municipal waste but use the
Check with your local authority for recycling advice. Customer participation is encour
environment and human health from the potential presence of hazardous substances.
Care and use
Disassembly and storage
Before using or re-using the silhouette light, inspect the arp points, please disposeproduct carefully. If there are any damaged parts or exposed sh
of the silhouette light.
amage:
shut.
Before storage, please repack the product as follows to avoid d
1. Gently lift off each section of the silhouette light.
2. Carefully place the silhouette light in its box and tape it
3. STORE PRODUCT IN A COOL AND DRY LOCATION. AWAY FROM SUNLIGHT AND WHERE THE TEMPERATURE DOES NOT EXCEED 40 C.
3. Connect the power transformer to the product, then plug the power transformer into the mains socket.
4. Press the button on the transformer sequentially to switch between the lighting modes below:
- Combination
- Waves
- Sequential
- Slow glow
- Chasing/flash
- Slow fade
- Twinkle/flash
- Steady on
3. Unplug the power transformer when not in use.
O
2. Choose a location to position the product. Please ensure it's stable, then use the stakes provided to secure it in place.