Homebase 6FT Norway Spruce User manual

6FT NORWAY SPRUCE
ARTIFICIAL TREE
INSTRUCTION MANUAL
IMPORTANT! Please read these instructions before using the product. Retain instructions for future use.
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576

Caution
• This tree is intended for INDOOR USE ONLY.
• Do not position or place the tree near fire, candles, or any other direct sources of heat. Avoid using in damp, wet and humid areas.
Do not position your tree where it is a hazard to the elderly, children or pets. Take particular care with electric cables.
• This product is for decoration purposes only. Trees have small parts which may pose a choking hazard if detached from the branches.
Not to be used by children as a toy. Keep out of reach of children and pets.
• Please check all fittings and re-tighten on a weekly basis, or as necessary.
• When you have finished using the tree, carefully re-pack following the instructions to ensure the tree remains in a good condition to be re-used.
Make sure the storage area is dry, avoid any damp, wet and humid areas.
• Retain assembly instructions for future use.
Before you start
Assembled dimensions Parts list
Parts List Qty
1. Please check that all parts are present before you start the assembly of your product, as once assembled, this product is exempt from our
money back guarantee. This does not affect your statutory rights.
2. For ease and speed of assembly, we recommend that before you commence each step, you identify all the parts required for that step.
3. For larger items, please ensure that you have sufficient space and people to assemble your product safely.
4. We recommend that, where possible, all items are assembled near to the flat area in which they will be placed in use, to avoid moving the
product unnecessarily, once assembled. Never allow any part of the set to come into contact with a source of heat or flames.
5. Please keep plastic bags out of reach of children and animals.
6. Locate your tree on a level surface that will not be damaged by the tree or decorations that could detach.
7. During assembly please take care not to over-tighten any fittings, as this may damage the product.
1800mm
1270mm
No.
1
2
3
4
5
1.
2.
3.
4.
5.
1
1
1
1
2
Tree top
Section 2
Section 1
Tree stand
Protective caps
2

4
Assembly
Step 1 Step 2
Pull apart the legs of the stand so that
they are snapped into an x-shape. Place
the tree stand on a level surface.
Assemble the tree from the bottom to the top. Remove
protective cap and insert the pole of 'section 1' into the
assembled stand. Insert the pole of 'section 2' into 'section 1'.
Insert the pole of the 'tree top' into 'section 2'. Ensure that
all poles are firmly secure.
Click
Spare parts
Each tree includes hinge pins/washers.
If extra parts are needed, please contact your local store.
1. Remove all decorations.
2. Disassemble the tree from the top to the bottom. Start with the 'tree top' and gently lift straight up to remove it from the section below,
then fold all branches toward the pole.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and rotate the upper pole in both
directions. Lift the upper pole up again.
4. Continue by gently lifting each section(s) straight up from the section below and fold all branches toward the pole, until the bottom
section is removed from the tree stand.
5. Carefully place all tree sections into the box and tape it shut.
6. When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to excessive heat or humidity may
damage your tree.
Disassembly and storage
Before using or re-using the tree, inspect the product carefully. If there are any damaged parts or exposed sharp points, please dispose of
the tree.
Care and use
Troubleshooting
Problem: Loose hinge pins
1. Extra hinge pins are included for repairing the hinges.
Place the branch into the slot of the bracket.
2. Insert a new hinge pin through the hole and secure
using the retainer washer.
3