HOMEDEPOT KF200189-01 User manual

1/12
Shoe cabinet
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
2 /12
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
3 /12
2.5 x 14 mm
6 x 30 mm
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
A x 4
4 x 40 mm
B x 17 C1 x 4 C2 x 4
C3 x 4
3.5 x 14 mm
1.5mm
D x 24
4 x 10 mm
6 x 30 mm4 x 12 mm
E x 4
4 x 20 mm
F x 4
G x 2 H x 4 I x 10 J1 x 1
J2 x 1 J3 x 1 L x 2 R x 2
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
4 /12
9
5
5
2
4
1
3
x2
6
8
7
7
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
D x 16 F x 4 G x 2 L x 2 R x 2
3.5 x 14 mm 4 x 20 mm
1
Assemble handle G to panel 6 and 10 using F.
holes as shown.
Attach this part to panel 6 and 10 using screw D to corresponding
5 /12
Fix plastic part L&R to panel 8, use screw D to tighten.
R
L
D
D
D
D
D
R
8
6
F
F
8
D
R
L
D
D
D
8
x2
D
R
L
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
D x 4
6 /12
3.5 x 14 mm
2
Attach panel 7 to the assembled part using
screw D slightly to tighten, as shown.
L
D
LD
D
R
7
6
LD
D
R
7
ED
3.5 x 14 mm 4 x 10 mm
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
7 /12
C1 x 4 C2 x 4
A x 2 B x 8 J1 x 1 J2 x 1
6 x 30 mm 4 x 40 mm 4 x 12 mm
J1
J2
J2
C2
C1
3
4
C1
C1
C2
C1
C1
C2
C2
C2
2
3
B
BB
B
B
B
3
9
5
A
A
B
B
1
5
Fix part J1 to panel 1 using screw J2.
Connect panel 1 with panel 3 using
wooden dowels A at first. Then use
screw B to tighten, as shown.
Attach panel 5 and 9 to panel 3
using screw B as well.
Hammer C1 & C2 slightly into the
holes on panel 2 &3, Note do not
tilt to avoid damage.
B
3
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
8 /12
A x 2 B x 8
6 x 30 mm
1.5 mm
4 x 40 mm
2.5 x 14 mm
B
5
H x 4 I x 10
6
H
I
B
B
B
B
3
9
5
B
B
A
A
B
B
2
1
5
H
H
H
I
I
I
I
I
I
I
I4
1
3
2
I
I
Fix panel 4 to the back of assembled
unit using screw I to pre-drilled holes
as shown.
Fix part H on the bottom.
Attach panel 2 to assembled part
in step 4, using screw B and
wooden dowels A as shown.
2
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
9/12
B x 1 J3 x 1
wall
1
B
4 x 40 mm 6 x 30 mm
WALL
WALL
J3
7
Find a proper height, fix J3 to wall as shown.
Using screw B to tighten, this could avoid
anti-dumping.
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA

FUFU&GAGA
FUFU&GAGA
10/12
C3 x 4
4 x 10 mm
8
E x 4
3
2
R
R
L
L
E
E
E
wall
EC3
Fix the plastic part L&R to panel 2&3 by
using C3 slightly. Then screw E to tighten.
6
E D
3.5 x 14 mm
4 x 10 mm
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA
FUFU&GAGA