HOMEDEPOT GHSC-1408 User manual

SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
Read instruction carefully . See Furniture Parts list and Hardware List for guidance . Be sure you have all parts before you start assembling .
Place and assemble furniture on a clean flat soft surface , such as carpet or rug to pervent being scratched .
Before you begin, please follow assembly instructions carefully, then follow them step by step.
Reminder:
Please ensure that all surfaces and edges with colours/laminations are facing forward/outward.
1
2
PART LIST
TOP PANEL 1 PC MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
1 PC
1 PC
31 PC
5
1 PC
4 PCS
1 PC
2 PCS
HARDWARE
A
B
C
D
E
F
G
6 SETS
M3.5 X 16MM C.B SCREW 40 PCS
ALLEN KEY M4 1 PC
BOTTOM PANEL
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW 6 PCS
A1 A2 A3
M8 X 30MM WOOD DOWEL 12 PCS
5/8 NAIL 35 PCS
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /4
1
1
DOOR PANEL (L)
DOOR PANEL (R)
BACK PANEL
M4 X 25MM C.B SCREW 6 PCS
5/8 HINGES 6 PCS
METAL SHELF SUPPORT 32 PCS
3 PCS
PVC HANDLE 108-160
PVC SQUARE LEG 5038 4 PCS
2
7
7
7
7
4
3
6
910
K
J
9
10
SHELF PANEL (L)
SHELF PANEL (R) 4 PCS
1 PC
CENTER PANEL
8
5
8
8
8
10
POWER DRILL
L
TIPPING PACK
2 SETS
L1
L2
L3
L4 L5
GHSC-1408

STEP 1 STEP 2
STEP 3 STEP 4
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /4
2
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware A2 onto panel (1).
(Repeat 4 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 12 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x6
A2
x4
ROTATE
x12
PRESS
B
1
3
4
- Attach panel (3), (4) and (5) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 6 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
F
ROTATE
Section View
x6
A2
A1
x6 PRESS
A3
3
5
1
Connect panel (2) to panel (3), (4) and (5) by using hardware C and F.
(Repeat 6 times.)
* In this step hardware B are pre-inserted.
5
3
1
2
ROTATE
x6
C
F
- Fix hardware K into panel (2) with hardware E.
( Repeat 4 times for each hardware.)
- Cover back the hardware K.
( Repeat 4 Times )
SCREWDRIVER
REQUIRED
x16
E
K
K
K
x4
ROTATE
PRESS
5
3
1
2
5
4
4
4
GHSC-1408

STEP 5 STEP 6
STEP 7 STEP 8
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /4
3
HAMMER
REQUIRED
Assemble panel (6) to entire body with hardware G.
(Repeat 35 times.)
x35
HIT
G
3
2
6
- Insert hardware I into mounting positions on panel (3), (4) and (5) by hand.
(Repeat 32 times.)
- Assemble the panel (7) and (8) into between panel (3), (4) and (5).
(Repeat 8 times.)
x32 PRESS
I
7
7
7
7
3
5
1
2
- Fix hardware H into panel (3), (4) and (5) by using hardware E.
(Repeat 2 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (9) and (10).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware H have been assembled in panel (9) and (10).
ADJUST
ROTATE
ADJUST
x12
H
H
HE
3
4
10
9
1
2
6
6
6
6
- Fix hardware H onto panel (9) and (10) by using hardware E.
(Repeat 2 times for each hardware.)
- Fix hardware J onto panel (9) and (10) by using hardware D.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
x6
D
ROTATE
x12 ROTATE
HE
9
10
J
4
8
8
8
8
10
J
10
GHSC-1408

STEP 9 STEP 10
STEP 11 STEP 12
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /4
4
Assemble hardware L1 into panel (1) and (6)
by using hardware L2.
(Repeat 2 times.)
SCREWDRIVER
REQUIRED - Mark and use the power drill
to drill a hole on the wall.
- Hit hardware L3 into the wall.
(Repeat 2 times.)
HAMMER
REQUIRED
POWER
DRILL
REQUIRED
- Assemble hardware L1 to L3 by using hardware L4.
(Repeat 2 times.)
SCREWDRIVER
REQUIRED - Connect two of the hardware L1 by using hardware L5.
- Tighten the hardware L5.
(Repeat 2 times.)
ROTATE x2
L1
L2 6
1
3
1
4
10
10
9
1
4
10
10
9
HIT
x2
L3
1
4
10
10
9
ROTATE x2
L1
L3
L4
TIGHTEN
CONNECT x2
L1
L1
L5
x2
L1
L1
L5
GHSC-1408