Homtime HS1-qi User manual
HS1-qi
Wireless Charging with Bluetooth Speaker
TIPS / IMPORTANT:
All safety and operation instructions should be read thoroughly before proceeding
and please keep the handbook for future reference.
IMPORTANT SAFETY INSTRUCTIONS
2
3
IMPORTANT SAFETY INSTRUCTIONS
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body
4
INFORMATION
Bluetooth Specification: 4.2+EDR
Bluetooth Profiles: HSP、HFP、A2DP
and AVRCP
Operating Distance: 10 meters Class II
Output Power: 3W+3W
Driver Unit: 4Ohm 3w 2in
Frequency Range: 40Hz-20KHz
S/N Ratio:＞65dB
Distortion Rate:＜1%
FM Frequency Range: 87.5-108MHz
SPECIFICATIONS
5
UNIT FEATURES & FUNCTIONS
FM FREQUENCY
USB MODE
ALARM TIME
SLEEP
TIME SETTING
TIME SETTING
TIME SETTING
6
UNIT FEATURES & FUNCTIONS
USB MODE
BLUETOOTH
NEXT SONG/Adjusting Alarm Time
VOL-
AUX IN
FM
BACKWARD SONG/Adjusting Alarm Time
Wireless Charging Wireless Charging Station
FM Mode
Skip Backwards last song/Adjusting Alarm Time
PLAY/PAUSE,TALK,SCAN FM
AUX IN Mode
Bluetooth&USB,Play/Pause,Answer the phone and Hang up,Auto scan FM station
USB Play Mode
Bluetooth Mode
Alarm Setting,On/Off
Skip Forwards Next Song/Adjusting Alarm Time
7
BASIC
When palying music, press“ ”to pause the
music. Press“ ” to skip backwards last song;
Press“ ” to skip forwards next song.
Press“ ” to put FM Radio on, “ ” appears
on the LCD display. Press and hold “ ” to auto
scan radio staon and store the scanned staons
3)
Press “ ”to put Bluetooth on. Go to moblie
seng, turn on Bluetooth and search Blue-
tooth devices. Connect “HS1-qi”. When it is su-
ccessfully paired,you will hear a sound of“DU”.
Play music from your mobile now.(when Blue-
tooth is connected,press “ ”or other mode
key to switching it to other mode, Bluetooth
will be OFF automacally and get disconnect-
ed with mobile. When switching it to Bluetooth
mode again,connect“HS1-qi”manually or auto-
macally.)
When a phone call is coming, press“ ”to
answer the phone.
HS1-qi OPERATION
ANSWER THE PHONE
SET ALARM TIME
When alarm is off, press “ “ to set alarm me.
Press “ ” or “ “ to adjust alarm me. It will
confirm and exit seng in 5 seconds if no
operaon on any key. Press “ ”to hand up when having a phone
call.
HANG UP
PLAY MUSIC
or press and hold
snooze.Alarm
socket
8
BASIC
The 3.7V lithium baery is to retain the clock/alarm
in case of a power failure. It can not display the
alarm/clock me when baery is low,need charge.
Back-up the lithium battery
Infrared remote control(Option)
Press“ ” to put AUX IN on,
“ ” appears on the LCD dis-
play. Pug in the 3.5mm audio
cable into the AUX IN jack.
Play music now.
accordingly.The frequency starts from 87.5MHz to
108MHz and skips at every 0 .1 MHz in scanning
process. Once catching a staon , it stops a second
and store it , then connues the auto-scanning.
When it scans from 87.5MHz to 108MHz, it will
stop scan automaccally. Press“ ” or “ ”to
select the staon.
Install the baery: Unscrew the back cover of
the remote control, open the screws, install 3
pieces AAA baery, lock the screw and screw the
back cover.
Sync me with phone: Unscrew the back cover
of the remote control, connect the remote
control's lightning connector to the iPhone
interface. In this way, the me will be synced with
iPhone.
Sync me with the reomte control: Align the
remote control with the alarm screen,press the
sync buon on the remote control, the me of the
remote control will be transmied to the alarm
clock and turn off the alarm, reset the alarm.
9
WIRELESS CHARGE
10
CARE AND MAINTENANCE / FAQs
11
NOTICE
Backup battery was low, so please charge it.
* Please comply with the actural product if there is
any discrepancy between the product and the
content of the manual
Table of contents
Other Homtime Speakers manuals
