Honeywell CN75 User manual

CN75/CN75e NI
with Windows®Embedded Handheld 6.5
Quick Start Guide
CN75NI-W65-EN-QS-0 Rev A
5/17

1
Introduction
This document is for the CN75/CN75e NI. This is the
non-incendive version of the CN75/CN75e. The CN75/CN75e
NI can be identified by the device label verifying non-incendive
certification.
Out of Box
Make sure that your shipping box contains these items:
• CN75/CN75e NI mobile computer
(Model CN75LAN or CN75WAN)
• Rechargeable 3.7 V, Lithium-ion battery
•I/OCover
• Product Documentation
If you ordered accessories for your mobile computer, verify that
they are also included with the order. Be sure to keep the original
packaging in case you need to return the mobile computer for
service.
Note: CN75LAN models do not include a WWAN radio.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC)
industrial grade microSD™ memory cards with the computer for
maximum performance and durability. Contact a Honeywell
sales representative for additional information on qualified
memory card options.
Warning: Explosion Hazard -Substitution of
components may impair suitability for Division 2 Class
I, II, III locations.
Avertissement: Risque d’ explosion - Le remplacement
de composants risque de compromettre l’adaptation
du produit aux sites de division 2 catégorie I,II,III.

2
Computer Features
Note: Hand strap not shown.
Notification LED
Scan Button
Microphone
Power Button
Battery Status
LED
Good Read LED
Speaker
Touch Panel
Volume Buttons

3
I/O Cover
Side Scan
Button
Speaker Port
Battery
Camera
Imager
(LED/Laser Aperture)
Laser Safety
Label Location
Application
Button
Battery Latch
SIM/microSD Card
Socket
(Located Under Battery)
Screws

4
Detach Hand Strap
Detach the hand strap to access to the back of the computer.
Note: Battery pack shown installed. To learn more, see “Install the
Battery”.

5
Install a microSD Card
Note: Format the microSD card before initial use.
Note: Always place the computer in hibernate mode and
remove the battery before attempting to install or
remove a card.

6
Install a SIM Card
Note: Always place the computer in hibernate mode and
remove the battery before attempting to install or
remove a card.

7
Install the Battery
The CN75/CN75e NI mobile computer ships with a Lithium-ion
3.7 V, 4000 mAH (14.8 Wh) battery manufactured for Honeywell
International Inc.
We recommend use of Honeywell Li-ion battery packs.
Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Ensure all components are dry prior to placing the
battery in the computer. Mating wet components may
cause damage not covered by the warranty.

8
Charge the Computer
The CN75/CN75e NI mobile computer ships with a partially
charged battery. Charge the battery with a 70 Series charging
device for a minimum of 6 hours.
Using the computer while charging the battery increases the
time required to reach a full charge. If the CN75/CN75e is
drawing more current than supplied by the charging source,
charging will not take place. For additional information, see the
user guide.
CN75/CN75e NI mobile computers are designed for use with
the following charging accessories: DX1 Desktop Dock, DX2
Dual Dock, and DX4 Quad Dock and a power supply.
Warning: Explosion Hazard - Batteries must only be
changed or charged in an area known to be
non-hazardous. Use ONLY Honeywell CN75 NI battery
part number 1000AB02.
Risqued’explosion-Les batteries doivent uniquement
être remplacées ou rechargées dans un endroit non
dangereux. Utilisez UNIQUEMENT Honeywell CN75 NI
batterie P/N 1000AB02
We recommend the use of Honeywell peripherals,
power cables and power adapters. Use of any non-
Honeywell accessories or power adapters may cause
damage not covered by the warranty.
Ensure all components are dry prior to mating the
computers and batteries with peripheral devices.
Mating wet components may cause damage not
covered by the warranty.

9
Install the I/O Cover
Remove the I/O Cover
The I/O cover must be attached when using the
CN75/CN75e NI in a dangerous environment.
Avertissement : Le couvercle entrée-sortie doit être
fi xé lorsque le CN75/CN75e NI est utilisé dans un
environnement incendiaire.
12
1 2