Honeywell HEV685 SERIES User manual

GETTING TO KNOW
YOUR COOL MOISTURE
EVAPORATIVE HUMIDIFIER
Invisible moisture
• Evaporative humidification
means you will NOT see
the moisture output.
• With evaporative humidification, a fan pulls
dry air from the room through the saturated
wicking filter. Moisture from the wicking filter
evaporates and is pushed into the room with
the help of the fan.
• Evaporative humidification adjusts moisture
output to the amount of moisture the air can
hold. The drier (less humid) the air in the room, the more moisture the humidifier will add to the
air. An evaporative humidifier cannot add more moisture to the room than the air can hold. The
amount of moisture the air can hold depends on many factors including relative humidity level,
temperature and size of room.
Instruction Manual
HONEYWELL TOP FILL
COOL MOISTURE HUMIDIFIER
MODEL HEV685 SERIES
REPLACEMENT FILTER: HONEYWELL HC-14 SERIES FILTER E
Humidity Level
• The ideal indoor humidity level is 40-60%
• Use a Honeywell humidity monitor
(HHM10 or H10C) to check your indoor
humidity level (not included)
Filter
• A wicking filter is required for this unit to operate
(one included)
• The wicking filter will help to capture minerals
from your water and will help to prevent white dust
(calcium deposits from hard water)
• If you have hard water, you will need to replace your
filter more frequently
• See “Caring for your Filter” section for tips on
prolonging the life of your wicking filter
For questions and information about this humidifier
Visit www.HoneywellPluggedIn.com or Call 1-800-477-0457

2 3
1. The humidifier should always be placed on a
firm, flat, waterproof surface at least four feet
(1.2 m) away from bedside, twelve inches
(30 cm) from the wall, and out of reach of
patients, children and pets.
2. Be sure the humidifier is in a stable position
and the power cord is away from heated
surfaces and out of the way to prevent the
humidifier from being tipped over.
3. Before using the humidifier extend the cord
and inspect for any signs of damage. DO NOT
use the unit if the cord has been damaged.
4. The humidifier has a polarized plug (one blade
is wider than the other) as a safety feature.
This plug will fit into a polarized outlet only one
way. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to
defeat this safety feature.
5. CAUTION: To avoid fire or shock hazard,
plug the humidifier directly into a 120V AC
electrical outlet. To avoid risk of fire, shock or
personal injury DO NOT use an extension cord
or power strip.
6. Shut off and unplug humidifier before moving.
The humidifier should always be unplugged and
emptied when not in operation or while being
cleaned. DO NOT move or tilt humidifier while it
is in operation. Plug and unplug humidifier with
dry hands. NEVER pull by cord.
7. When moving or lifting the full Water Tank,
use two hands; one hand on the Tank
Handle and the other on the bottom of
the Tank.
8. DO NOT add any medications, inhalants,
scented products or essential oils into Base,
Water Reservoir or Water Tank.
9. DO NOT cover or insert objects into any
openings on the humidifier.
10. DO NOT block intake or output vents.
11. DO NOT operate the humidifier without
water. Turn off and unplug unit when Tank
is empty.
12. Humidifier requires regular cleaning. Refer
to, and follow, cleaning instructions.
13. DO NOT operate outdoors; this appliance
is intended for indoor use.
14. DO NOT attempt to repair or adjust any
electrical or mechanical functions on this
humidifier. Doing so will void your warranty.
15. For residential use only.
SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
READ AND SAVE THESE SAFETY INSTRUCTIONS
BEFORE USING THIS HUMIDIFIER
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
GETTING TO KNOW YOUR HUMIDIFIER
Water
Tank
Plunger
Housing
Water
Reservoir Base
Motor
Housing
Power/Output
Knob
Humidity
Level Knob
Wicking
Filter
Plunger
Tank Cover
Tank Handle
Intake
Grill
Humidity
Reached
Indicator
Refill
Indicator
Float Paddle
Auto Shut Off
Float
How It Works:
Water is released into the Reservoir when the Float Paddle engages the Plunger at the bottom
of the water tank. A Wicking Filter absorbs water from the Reservoir. A fan pulls dry air from
the room into the humidifier where it passes through the saturated Wicking Filter. The filter
captures minerals and other impurities from the water, before the moisture is evaporated back
into the dry room with the help of the fan. The amount of moisture output depends on many
factors, including the current room humidity and temperature. As the humidity level in the
room increases, the moisture output decreases, which prevents over humidification.

4 5
1. Remove Water Tanks and set aside. Remove Housing and lift up to expose Wicking Filter.
2. Carry Wicking Filter and Base to sink or tub.
3. Remove Filter from Base and run under cool water until saturated.
4. Carefully place wet Filter back in base; DO NOT squeeze out excess water.
1. Remove Water Tanks. Under each tank, identify the Brackets where the Float Paddle will be installed.
2. Place the Float Rod over both Brackets and press firmly until you hear it click into both Brackets.
3. Pull up gently on Float Rod to be sure it doesn’t pop out of either of the Brackets. Replace the Water Tank.
Repeat with second Tank and Float Paddle.
Step 3Step 2
$
Step 4
$
Step 1
Step 2
FILLING/REFILLING WATER TANKS
1. Flip Tank Cover open.
2. Pour water into the Tank opening.
3. Close Tank Cover to keep objects and debris out of water.
Repeat to fill second Water Tank.
Step 1 Step 3
The Tanks can be filled in two ways.
To fill at the humidifier:
Float Paddle Installation – required for humidifier to operate
This humidifier uses a float system to regulate the water flow from the Tank to the Reservoir. The Float
Paddles must be properly installed for the unit to operate. If not properly installed, water may not flow into
the Reservoir or it may leak from the Base. The Float Paddle is designed to be easy to install and remove.
CAUTION: Improper placement of the Float Paddles could result in leaking or water not feeding
to the Reservoir.
Step 3
Step 2
Top Le Haut
“Click”
Step 1
Float
Rod
Float
Paddle
Brackets
Preparing the Wicking Filter
To speed the delivery of moisture into your room it is recommended to wet the wicking filter before use.
Step 2
$
Step 1
$
Step 4
Step 3
To fill at the sink or tub:
1. Flip Tank Cover open. Grasp Tank Handle and lift Water Tank to remove from Base. Carry Tank to sink
or tub. NOTE: DO NOT use the Tank Cover to carry Water Tank.
2. Fill Tank with water. When filling, allow enough space at the top to minimize splashing when carrying.
Use cool tap water; DO NOT use warm or hot water.
3. Carry Water Tank back to humidifier using two hands; one hand on Tank Handle at the top of the Tank
and other hand supporting the bottom of the Tank. Take care not to push the Plunger on the bottom of
the Water Tank or leaking may occur.
4. Place the Water Tank on the humidifier Base. You may hear the water draining into the Reservoir.
Repeat to fill the second Water Tank.
NOTE: If the wicking filter has dried out, it may take up to a minute for the humidifier to turn back on while
the wick absorbs the water.
CAUTION: Use care when handling Water Tanks to avoid unnecessary impact. Banging
or dropping the Water Tanks could result in damage to the Tank that may cause leaking.
1. Open box and locate locate the two (2)
Float Paddles and set aside. These must be
installed for the humidifier to operate properly.
2. Place the humidifier on a firm, level, water resistant
surface at least 12” (30 cm) from any walls.
DO NOT block Intake Grill on base of unit. DO NOT
place on surfaces that can be damaged by water.
Unpack the Humidifier (Keep this instruction manual for reference.)
SETTING UP YOUR HUMIDIFIER
Step 1 Step 2
Float
Rod

6 7
To prolong the life of your Wicking Filter, turn it over each time you fill the Water
Tank. This will keep the top of the Filter from drying out and will help the Filter
to age more evenly.
If you notice the Filter getting hard, you may soak it in cool water to loosen mineral
buildup. This will temporarily improve performance of the Wicking Filter until a
replacement Filter is purchased.
DO NOT attempt to clean the Wicking Filter with vinegar, soap or any chemical
solutions. Doing so may damage the Filter.
Protec
®
antimicrobial layers in the Wicking Filter help to prevent growth of mold on the Filter. However, the
Filter still needs to be replaced regularly. Humidifier Filters and accessories require replacement and are not
covered under warranty.
CARING FOR YOUR FILTER
It is recommended you change your Wicking Filter every 30-60 days depending
on water quality and usage. If you have hard water you may need
to replace your Filter more frequently.
Change your Filter if you notice:
• The Filter is hard and crusty • The Filter starts to give off an odor
• Moisture output is decreased
Be sure to use only genuine Honeywell Replacement Filters which are
Protec
®
antimicrobially treated. It helps prevent the migration of mold,
algae and bacteria on the filter.
Replacement Wicking Filter
Honeywell HC-14 Series, Filter E
Follow steps 1-3 under Before Cleaning, then follow the additional steps below.
NOTE: Filter must be removed from humidifier during cleaning; DO NOT clean Filter with vinegar.
1. Pour up to 2 cups of undiluted distilled white vinegar into each Water Tank. Swish vinegar around in Tank
to wet entire inside of Tank.
2. Place Tanks on Base. Vinegar will drain into Water Reservoir and loosen mineral buildup (Scale) in
Base, Reservoir and bottom of the two Water Tanks. Allow vinegar to remain in the Tanks and Base for
20 minutes.
3. Empty vinegar from Tanks and Base and use a cloth or soft brush to help remove scale.
Remove Float Paddles and wipe clean with vinegar. Replace Float Paddles and ensure each one is secured
in both brackets. See Float Paddle Installation instructions in the Setting Up Your Humidifier section.
4. Rinse Base and Reservoir with clean water until the smell of vinegar is gone.
Step 3 Step 4 Step 2
V
2C
Step 1
Scale Removal
CARING FOR YOUR HUMIDIFIER
Step 2
$
$
Step 1
1. Turn off and unplug humidifier. Never clean the humidifier when it is running.
2. Empty water from Water Tanks.
3. Remove Motor Housing, Wicking Filter and any other accessories from humidifier and set aside.
Before Cleaning
Step 3
$
$
MINUTES
Power Control
1. With Power Knob in the OFF position, plug humidifier into a polarized 120V outlet.
CAUTION: To avoid electric shock, do not plug humidifier into outlet with wet hands.
2. Turn the Power/Output knob to desired fan setting.
High ( ): Fast humidifying Medium ( ): Everyday moisture control Low ( ): Quiet setting
Humidity Control
3. Turn the Humidity Level Knob to the highest setting and run for at least an hour or until a comfortable
humidity level is reached.
4. Once comfortable, turn the Humidity Level Knob to the left until the green Humidity Reached Indicator light
turns on ( ) and the humidifier turns off. This is your desired humidity level. Now that your desired
humidity level is set, the humidifier will automatically turn back on when your room drops below this
comfort setting and will automatically turn off again when the comfort setting is reached.
NOTE: For continuous operation, set to high ( ).
Water Tanks
5. When both Water Tanks are empty, the humidifier will automatically shut off and the orange Refill Indicator
() will light up. Turn off the humidifier and refill the Tanks. See Filling/Refilling Water Tanks on
previous page.
NOTE: If the humidifier will not be used for more than a few days, empty the water from the Water Tanks
and Water Reservoir and dry out the Filter to prevent growth of bacteria or mold
.
Step 2
$
Step 1 Step 3 Step 4 Step 5
USING YOUR HUMIDIFIER CARING FOR YOUR FILTER (Continued)
NOTE: While the humidifier is operating, you will hear the fan running but
will not see the moisture output. This is normal for an evaporative humidifier.
To check the humidity level in the room, use a humidity monitor like
the Honeywell HHM10 or H10C, available at retailers or online at
www.HoneywellPluggedIn.com.
To keep your humidifier running efficiently, clean it regularly. Weekly cleaning is recommended. All
maintenance should be done in the kitchen or bathroom on a water resistant surface near a faucet.
DO NOT wash any components of this humidifier in a dishwasher.
To properly clean your humidifier we recommend the separate processes of Scale Removal and Disinfecting.
These two processes must be done separately.

8 9
CARING FOR YOUR HUMIDIFIER (Continued)
B
1tsp. (3.8 L)
W
1 Gal.
Step 1
$
$
Step 2
Follow steps 1-3 under Before Cleaning, then follow the additional steps below.
NOTE: Filter must be removed from humidifier during cleaning. DO NOT clean Filter with bleach solution.
1. Mix 1 gallon (3.8L) of water with 1 teaspoon of bleach. Pour half of the bleach solution into first
Water Tank. Lift Tank and swish bleach solution around to wet entire inside of Tank. Repeat for
second Water Tank.
NOTE: Using more than 1 teaspoon of bleach to 1 gallon (3.8L) of water may result in damage to
the humidifier.
2. Place both Tanks on Base. Bleach solution will drain into Water Reservoir.
3. Allow bleach solution to remain in the Tanks and Base for 20 minutes.
4. Empty bleach solution from Tanks and Base. Rinse with clean water until the smell of bleach is gone.
Be sure both Float Paddles are secured before filling Tanks with water. See Float Paddle Installation
instructions in the Setting Up Your Humidifier section.
CAUTION: Improper placement of the Float Paddles could result in leaking or water not
feeding to the Reservoir.
TROUBLESHOOTING
MINUTES
Step 3 Step 4
Disinfecting
End of Season Cleaning
Follow cleaning instructions above when the humidifier will not be used for at least one week, or it is the
end of the season. Remove any accessories, including the Wicking Filter, and allow the humidifier to dry
completely before storing.
DO NOT store humidifier with water inside the Base, Water Reservoir or Water Tanks. At end of season,
remove and throw away filter. DO NOT store humidifier with a used Wicking Filter.
NOTE: Consider using a Protec
®
Cleaning Ball to keep your humidifier
cleaner longer. It will continuously clean and protect against bacteria
and mold. It will also help prevent the buildup of slime in the water
and on humidifier surfaces. The Protec Ball will keep your humidifier
cleaner longer between cleanings. However, your humidifier still needs
to be cleaned regularly.
Problem Possible Cause Solution
Power Knob is turned to
high ( ) med ( ) or low
() but no lights are on,
and the unit is not running
Unit is not plugged in
No power at outlet
Plug unit in
Check home circuits, fuses;
test outlet
Green light ( ) is on
but fan is not running
Set humidity level has been
reached ( )Turn Humidity Control Knob to a
higher setting
Power Knob is turned to
high, med or low and the
Refill light ( ) is on
Water level may be low
Motor Housing not properly
seated on Base
Check water level of each tank
and refill if necessary
Lift and replace Motor Housing
to ensure it is properly sitting
on the base
Humidifier shuts off Set humidity level has
been reached
Water Tanks are empty
Increase Humidity Control
setting
Fill the Water Tanks with water
Water is not draining
into Reservoir
Float Paddle is not installed
correctly
Plunger is stuck
See Float Paddle Installation
instructions in Setting Up Your
Humidifier
Push and release Plunger to be
sure it is moving freely
Water leaking from Base
or Reservoir Float Paddle is not installed correctly
Plunger is damaged
Plunger is sticking
Plunger may have foreign material
stuck under the Gasket
Tank is cracked
See Float Paddle Installation
instructions in Setting Up
Your Humidifier
Contact Consumer Relations
Push and release Plunger to be
sure it is moving freely
At sink, push and release Plunger
system so water may flow
Inspect tank for damage;
contact Consumer Relations
Tank and Base are slimy
Odor coming from grill
Need to clean
Filter needs to be replaced
See Caring for your Humidifier
Replace with Honeywell HC-14
replacement wicking filter
Fan is running but water
level is not going down Filter is clogged with mineral deposits See instructions for Caring for your Filter; purchase a new
Honeywell Replacement Filter
For additional troubleshooting help, call Consumer Relations at 1-800-477-0457.