Honeywell Pro-Watch 7000 User manual

Install Guide
Pro-Watch 7000
Output Module
PW7K1OUT

Copyright© 2020 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their
respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this
document at any time without prior notice.
Pro-Watch® is a trademark of Honeywell International, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellintegrated.com for information
about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at www.honeywellintegrated.com to
post your comments.
Discover | Customer Portal
Self-Service Product Support and Learning Management System
https://honeywelldiscovertraining.com/login/discover/default.asp
YouTube | Honeywell Help and Support
https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 i
TABLE OF CONTENTS
Notices......................................................................................................................................... iii
Warnings and Cautions........................................................................................................ iii
Disclaimer....................................................................................................................................v
Compliance .................................................................................................................................v
CE + WEEE Marking............................................................................................................... vi
Unpacking Procedure ........................................................................................................... vi
Shipping Instructions ........................................................................................................... vi
Limited Warranty ................................................................................................................... vii
Confidentiality ........................................................................................................................ vii
Chapter 1 - PW-7000 Output Module..........................................................1
Description ................................................................................................................................. 1
Specification.............................................................................................................................. 2
Set Up ........................................................................................................................................... 3
LED Operation .......................................................................................................................... 4
Power ............................................................................................................................................ 5
Communications ..................................................................................................................... 5
Wiring ........................................................................................................................................... 6
Mounting Options ................................................................................................................... 7
Installing the Module............................................................................................................. 7
Wiring Diagram for Connectors 1 through 8................................................................ 9
Wiring Diagram for Connectors 7 through 10 .......................................................... 10

ii PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
This page is intentionally left blank

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 iii
Notices
Warnings and Cautions
Wiring methods shall be in accordance with the National Electrical Code (ANSI/
NFPA70), Canadian Electrical Code, Part I (CSA C22.1) Safety Standard for Electri-
cal Installations, local codes, and the authorities having jurisdiction.
Before installation, TURN OFF the external circuit breaker which supplies power to
the system.
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or death could occur, and the equipment could be damaged
beyond repair, if this precaution is not observed!
Never connect card readers to any critical entry, exit door, barrier, elevator, or gate
without providing an alternative exit in accordance with all fire and life safety
codes pertinent to the installation. These fire and safety codes vary from city to city
and you must get approval from local fire officials whenever using an electronic
product to control a door or other barrier. Use of egress buttons, for example, may
be illegal in some cities. In most applications, single action exit without prior
knowledge of what to do is a life safety requirement. Always make certain that any
required approvals are obtained in writing. DO NOT ACCEPT VERBAL APPROVALS,
BECAUSE THEY ARE NOT VALID.
Honeywell never recommends using the PW-7000 or related products for use as a
primary warning or monitoring system. Primary warning or monitoring systems
should always meet local fire and safety code requirements. The installer must also
Warning:
Before installation, TURN OFF the external circuit breaker which supplies power to the system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Warning: Fire Safety and Liability Notice (Not Evaluated by UL for fire,
life safety, or burglary applications)

iv PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
test the system on a regular basis by instructing the end user in appropriate daily
testing procedures. Failure to test a system regularly could make the installer liable
for damages to the end user if a problem occurs.
Note: See the Remote Enclosure Installation manuals PW5K2ENC1/PW5K2ENC2 or
PW5K1ENC3 for installation instructions.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This document and the data in it shall not be duplicated, used, or disclosed to others
for procurement or manufacture, except as authorized by and with the written
permission of, Honeywell, Inc. The information contained in this document or in the
product itself is considered the exclusive property and trade secrets of Honeywell,
Inc. Copyright laws of the United States protect all information in this document or in
the software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell, Inc.
Software Agreement. Please request a copy from Honeywell, Inc., and review the
agreement carefully.
Warning:
EARTH ground all enclosures for proper installation.
Warning:
Use suppressors on all door strikes. Use S-4 suppressors for installation. Honeywell
recommends only DC strikes.
Caution:
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE FILED WITH THE
COMMERCIAL CARRIER RESPONSIBLE.
Caution:
Electrostatic discharge can damage CMOS integrated circuits and modules. To prevent
damage, always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static-controlled workstation. These
workstations consist of a desk mat, a floor mat, and an ESD wrist strap. Workstations are
available from various vendors.

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 v
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component
thereof has caused personal injury or damage to property of others, Customer
shall immediately notify Honeywell in writing of all such claims. Honeywell shall
defend or settle such claims and shall indemnify and hold Customer harmless for
any costs or damages including reasonable attorneys' fees which Customer may
be required to pay as a result of the defective Product or the negligence of Honey-
well, its agents, or its employees.
Customer shall hold harmless and indemnify Honeywell from and against all
claims, demands, losses, and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer
and its agents and employees, and from and against all claims, demands, losses,
and liability for costs of fees, including reasonable attorneys' fees, in connection
therewith.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website, https://www.security.honeywell.com/All-Categories/
access-control-systems/control-panels-hardware. For any additional information
regarding the compliance of this product to any EU-specific requirements, please
contact:
Honeywell Security & Communications
Honeywell Security - Quality Assurance Dept., Newhouse Industrial Estate Mother-
well
Lanarkshire ML1 5SB Scotland
United Kingdom
Tel: [phone]
Email: [e-mail]
CE and WEEE Marking
Description of the used symbol.
CE -Standard -Logo. This product complies with
the harmonized Regulation of the EU
WEEE symbol.It indicates this product is to be
recycling and not been thrown in the dustbin

vi PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
Unpacking Procedure
All containers should be opened and unpacked carefully in order to prevent dam-
age to the contents.
The following steps are used to unpack equipment in preparation for installation:
Step 1. Open the container and remove the unit(s) and all packing material.
Retain the container and all packing materials. They may be used again
for reshipment of the equipment, if needed.
Step 2. Inspect the contents for shortage. If items are missing items, contact the
order entry department at 800-323-4576.
Step 3. Visually check contents. If damage is discovered, perform the following:
• If shipping caused damage to the unit, a claim must be filed with the
commercial carrier.
• If any other defect is apparent, call for a return authorization.
Shipping Instructions
To ship equipment back to Honeywell, Inc.:
Step 1. Contact the customer service department at 800-323-4576 before
returning equipment. When you call please have available:
• A description of the problem or reason you are returning the equipment.
• Your original purchase order number, invoice number and if the unit is still
under warranty.
• A new purchase order number if the unit is not under warranty.
Step 2. From the customer service department, obtain the Return Authorization
Number (RMA).
Step 3. Show the RMA number on all packages shipped. Packages which are not
marked with an RMA number will be refused at the factory and returned
to you COD.
Step 4. Carefully pack the equipment for shipment. Use the original packing
material whenever possible.
Caution:
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercial carrier.

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 vii
Limited Warranty
All Products sold or licensed by Honeywell include a warranty registration card
which must be completed and returned to Honeywell by or on behalf of the end
user in order for Honeywell to provide warranty service, repair, credit or exchange.
All warranty work shall be handled through Customer which shall notify Honeywell
and apply for a Return Merchandise Authorization (RMA) number prior to returning
any Product for service, repair, credit, or exchange. Honeywell warrants that its
Products shall be free from defects in materials and workmanship for a period of
two years from date of shipment of the Product to Customer. The warranty on Ter-
minals, Printers, Communications Products and Upgrade kits is 90 days from date
of shipment.
Satisfaction of this warranty shall be limited to repair or replacement of Products
which are defective or defective under normal use. Honeywell's warranty shall not
extend to any Product which, upon examination, is determined to be defective as a
result of misuse, improper storage, incorrect installation, operation or mainte-
nance, alteration, modification, accident or unusual deterioration of the Product
due to physical environments in excess of the limits set forth in Product manuals.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OF MERCHANT-
ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. NO REPRESENTATION
OR WARRANTY OF THE DISTRIBUTOR SHALL EXTEND THE LIABILITY OR
RESPONSIBILITY OF THE MANUFACTURER BEYOND THE TERMS OF THIS PRO-
VISION. IN NO EVENT SHALL HONEYWELL BE LIABLE FOR ANY RE-PROCURE-
MENT COSTS, LOSS OF PROFITS, LOSS OF USE, INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES TO ANY PERSON RESULTING FROM THE USE OF HON-
EYWELL'S PRODUCTS.
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell relating to the design, use and service of
the Products shall remain confidential and shall constitute proprietary rights of
Honeywell and Customer agrees to treat such information as confidential. Cus-
tomer shall acquire no rights in the design of the Products or the related materials
except to use such information solely for the purpose of and only during the time it
sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be
used any Product design or related materials for its own benefit or for the benefit of
any other party. The covenants contained in this section shall remain effective
throughout the term of this Agreement and thereafter unless specifically waived by
Honeywell in writing.

viii PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
This page is intentionally left blank

CHAPTER
1
PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 1
PW-7000 OUTPUT MODULE
Description
The Output Board provides connections for 16 relay outputs. You can either mount
the board in a rack or open flat. If you rack-mount the board, only one edge is
accessible for wiring; however, a flat mount increases the amount of available I/O
slightly but significantly decreases the number of boards that can be mounted in
one enclosure.
Starting at the bottom of the rack-mount side of the board:
• The first connector provides power to the board.
• The next connector provides communication with the Controller (PW7K1IC or
PW6K1IC).
• Continuing up this edge, the next six connectors provide 12 relay output
connections.
When the board is mounted flat, four additional relay outputs and two dedicated
inputs for cabinet tamper and power fault detection are provided on the opposite
edge of the board.
All 16 form-C relay outputs are designed to handle dry-circuit signals. The two
dedicated inputs are non-supervised. Communication to the control panel is
accomplished via an RS-485 interface. This board requires 12 VDC input power.
When communication to the controller is lost, this board maintains all previous
output settings at the time communication was lost.

2 PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
Specification
The Output Board is for use in low voltage, class 2 circuits only.
Primary power:
12VDC + 10%, 385mA maximum
Relay contacts:
Relays 0 through 15 outputs, Form-C, 2A @ 30VDC, resistive
Inputs:
Two unsupervised dedicated inputs
Communication:
Wire requirements:
Mechanical:
Environment:
RS-485 Range 9,600 to 38,400 bps
Power 1 twisted pair, 18AWG
RS-485 24AWG, 4,000 feet (1,200 m) max., 2 twisted pair with shield
(120?, 23pF) (Belden 9842 or equiv.)
Inputs 1 twisted pair per input, 30 ohms max.
Outputs As required for the load
Dimension 5.5" (140 mm) W x 9" (229 mm) L x 1" (25 mm) H
Weight 12 oz. (340 g) nominal
Temperature 0°C to +49°C, operating, -55°C to +85°C, storage
Humidity 0% to 85% RHNC

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 3
Set Up
Table 1: PW-7000 Output Module Jumper Setting
Table 2: PW-7000 Output Module DIP Switch Settings
Jumper Setting Default Selected
J1 OFF * Port 1 RS-485 EOL terminator is not active
ON Port 1 RS-485 EOL terminator is active
S8 S7 S6 S5 S4 S3 S2 S1 Selection
OFF OFF OFF OFF OFF ADDRESS 0
OFF OFF OFF OFF ON ADDRESS 1*
OFF OFF OFF ON OFF ADDRESS 2
OFF OFF OFF ON ON ADDRESS 3
OFF OFF ON OFF OFF ADDRESS 4
OFF OFF ON OFF ON ADDRESS 5
OFF OFF ON ON OFF ADDRESS 6
OFF OFF ON ON ON ADDRESS 7
OFF ON OFF OFF OFF ADDRESS 8
OFF ON OFF OFF ON ADDRESS 9
OFF ON OFF ON OFF ADDRESS 10
OFF ON OFF ON ON ADDRESS 11
OFF ON ON OFF OFF ADDRESS 12
OFF ON ON OFF ON ADDRESS 13
OFF ON ON ON OFF ADDRESS 14
OFF ON ON ON ON ADDRESS 15
ON OFF OFF OFF OFF ADDRESS 16
ON OFF OFF OFF ON ADDRESS 17
ON OFF OFF ON OFF ADDRESS 18
ON OFF OFF ON ON ADDRESS 19
ON OFF ON OFF OFF ADDRESS 20
ON OFF ON OFF ON ADDRESS 21
ON OFF ON ON OFF ADDRESS 22
ON OFF ON ON ON ADDRESS 23
ON ON OFF OFF OFF ADDRESS 24
ON ON OFF OFF ON ADDRESS 25
ON ON OFF ON OFF ADDRESS 26
ON ON OFF ON ON ADDRESS 27
ON ON ON OFF OFF ADDRESS 28
ON ON ON OFF ON ADDRESS 29
ON ON ON ON OFF ADDRESS 30
ON ON ON ON ON ADDRESS 31
OFF OFF Reserved

4 PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
* = Default
LED Operation
The Output Board uses two onboard LEDs to provide status information during the
power-up sequence and during normal operation.
Table 3: LED Settings
In addition to the status LEDs, there are 16 additional LEDs on board for relay sta-
tus. When any relay is energized or ON, its corresponding status LED turns ON
also. The LED remains ON for as long as the relay is energized. The assignment for
each relay status LED is shown in the following table.
Table 4: Relay LEDs: 0-7
Table 5: Relay LEDs: 8-15
The following table lists the LEDs D1 through D4.
OFF ON 9,600 BPS
ON OFF 19,200 BPS
ON ON 38,400 BPS*
OFF Not Used*
S8 S7 S6 S5 S4 S3 S2 S1 Selection
Mode LED
D1
LED
D2 Description
Power-up
sequence
ON OFF Start power-up, hardware setup.
OFF ON Testing RAM.
ON ON Testing ROM and completing initialization.
FLAS
H
ON LED D1 flashes four times after power-up is completed.
Normal Operation FLAS
H
This is the processor heartbeat LED. It flashes once every second. A short ON
time (~20% duty cycle) indicates the board is offline or has lost serial
communication with the Controller board. A long ON time (~80% duty cycle)
indicates the board is online and communicating with the Controller board.
FLAS
H
Flash when there is activity on its Serial Port.
RELAY # 0 1 2 3 4 5 6 7
LED D5 D6 D7 D8 D9 D10 D11 D12
RELAY # 8 9 10 11 12 13 14 15
LED D13 D14 D15 D16 D17 D18 D19 D20

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 5
Table 6: LEDs 1-4
Power
The Output Board accepts 12VDC with an operating range of 10 to 14VDC and
consumes 385 mA of current. Locate the power source as close to this board as
possible. Connect power with minimum of 18AWG cables.
Note: POLARITY for 12VDC power is important. Make sure the +12 VDC is connected to the
terminal labeled +12V and the return is connected to the terminal labeled GND.
Communications
The Output Board communicates to the host controller through an RS-485 inter-
face. The interface allows for multi-drop communication of up to 4,000 feet (1,200
m) total per port. Use two twisted pair (minimum 24AWG) with shield (Belden 9842
or equiv.) for communication. The default speed of this port is 38.4Kbps but it can
be downgraded to 19.2Kbps or 9.6Kbps if the line conditions or receiving equip-
ment require it (see Table 1: PW-7000 Output Module Jumper Setting (page 3) for
jumper settings and Table 2: PW-7000 Output Module DIP Switch Settings (page
3) for DIP switch settings).
For wiring to an RS-485 port:
Step 1. TR+ is the plus side of the transmit and receive differential signal.
Step 2. TR- is the negative side of the transmit and receive differential signal.
Step 3. GND is the signal ground. The wiring for this signal is required and NOT
optional. This signal must NOT be connected to chassis GND.
LED number Description
D1 Start power-up, hardware setup
D2 Testing RAM
D3 Tamper
D4 Power

6 PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
Step 4. Use 24 AWG low capacitance, two twisted-pair, shielded cable (Belden
9842 or equiv.).
Note: For RS-485 Communication Connections, twist the blue pair together and use as the
common; use the orange pair as your data pair, observing polarity. Connect the
external drain shield to the appropriate earth ground on one end.
Step 5. When daisy-chaining RS-485 ports together, connect the TR+ wires from
the upstream and downstream boards to the TR+ terminal. Likewise,
connect the TR- wires from the upstream and downstream boards to the
TR- terminal.
By factory default J1 is set open. If this board is the last board on the RS-485 bus,
install jumper J1 across both pins (closed). Closing J1 provides the bus termina-
tion required.
Wiring
This section provides input wiring and control output wiring information.
Input Wiring
Inputs TMP and PFL are typically used for monitoring cabinet tamper and power
failure respectively. These two inputs are not supervised and are not accessible
when the board is rack-mounted. These inputs are used when this board is
mounted remotely and cannot take advantage of the tamper and power fail detect
inputs on the Controller board. If these inputs are not used, install a short piece of
wire at the input to indicate safe condition.
Control Output Wiring
Sixteen form-C relay contacts are provided as general-purpose outputs. They are
configurable as standard (energize to activate) or fail-safe (de-energize to activate)
by the host software.
The energized or ON time of each relay can be configured using pulse control for
single or repeating pulses via the host software. The energized or ON time of a sin-
gle pulse can be extended up to 24 hours. For repeating pulses, the on/off time can
be defined in 0.1 second increments and be repeated up to 255 times.

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 7
All 16 relays are rated for dry contact signal or load switching. While they are sized
to handle typical loads, load switching can cause abnormal contact wear and pre-
mature contact failure. Switching of inductive loads (e.g., strikes) also causes EMI
(electromagnetic interference) which may interfere with normal operation of other
equipment. To minimize premature contact failure and to increase system reliabil-
ity, a contact protection circuit is recommended. The following two circuits are sug-
gested. Locate the protection circuit as close to the load as possible (within 12
inches [30cm]); the effectiveness of the circuit decreases as the distance from the
load increases.
Relays 12 through 15 are general purpose relay outputs and are not available
when the board is rack-mounted.
Use sufficiently large gauge of wires for the load current to avoid voltage loss.
Mounting Options
This board can be mounted on-edge in the rack-mount enclosure provided by
Honeywell, or it can be mounted flat against any surface using standoffs under the
mounting holes provided in each of the four corners of this board.
When this board is rack-mounted, the connectors for four general-purpose out-
puts and two dedicated inputs are not accessible and should not be used.
The most likely reason for mounting a board flat is that it is being installed
remotely to be located near the door(s) being monitored. In this case, mount it in its
own enclosure. Use the two dedicated inputs to monitor cabinet tamper and power
fault.
The four additional general-purpose outputs allow for control of local horns or
other equipment.
Installing the Module
Step 1. Set Jumpers and DIP switches.
Step 2. Mount this board in the appropriate enclosure. If this board is being
mounted in a rack, the component side of the board is to your right as you
face the rack.
Step 3. Connect the communications and power supply to the circuit boards with
the Power Supply Harness.
Step 4. Connect wiring to input sensors or install jumper wire as appropriate.
Warning: DO NOT CONNECT THE POWER SUPPLY TO THE AC SOCKET
UNTIL ALL WIRING HAS BEEN INSTALLED AND RECHECKED.

8 PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
Step 5. Connect relay output wiring as appropriate.
Step 6. Connect communications wiring to the Intelligent Controller.
Step 7. Recheck wiring for correct connections and continuity.
Step 8. When all boards have been installed, connect the power supply cord for
proper connections and power.
Step 9. Set up the panel controls using the host software.

PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1 9
Wiring Diagram for Connectors 1 through 8
Figure 1: PW-7000 Output Module Wiring: Connectors 1-8
DIP SWITCHES
ON
OFF
87654321
OUTPUT BOARD Short
together*
Power
RS-485
RS-485 TR+
RS-485 TR-
RS-485 GND
+ 12V
GND
RELAY10 NO
RELAY10 C
RELAY10 NC
RELAY11 NO
RELAY11 C
RELAY11 NC
RELAY8 NO
RELAY8 C
RELAY8 NC
RELAY9 NO
RELAY9 C
RELAY9 NC
RELAY6 NO
RELAY6 C
RELAY6 NC
RELAY7 NO
RELAY7 C
RELAY7 NC
RELAY4 NO
RELAY4 C
RELAY4 NC
RELAY5 NO
RELAY5 C
RELAY5 NC
RELAY2 NO
RELAY2 C
RELAY2 NC
RELAY3 NO
RELAY3 C
RELAY3 NC
RELAY0 NO
RELAY0 C
RELAY0 NC
RELAY1 NO
RELAY1 C
RELAY1 NC
K 1 K 2 K 3 K 4 K 5 K 6 K 7 K 8 K 9 K 10 K 11 K 12
K 13 K 14 K 15 K 16
J 2
{
CardRack PWR &
Com Harness* (Rack
Mount
Only)
* Rack Mount Conguration
J 1 - RS-485
Termination
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
1
2
3
1
2
3
4
5
6
1
2
3
4
5
6
0
123456 7891011
D1 D2 D3 D4
D17 D18 D19 D20

10 PW-7000 Output Module (PW7K1OUT) Installation Guide, Document 800-25675V1
Wiring Diagram for Connectors 7 through 10
Figure 2: PW-7000 Output Module: Connectors 7-10
DIP SWITCHES
ON
OFF
87654321
16 OUTPUT BOARD
Power
RS-485
The connectors on
this side of the board
are not accessible
when it is rack
mounted.
RS-485 Com Bus
Cable From Dif.
Panel (Remote
Mount Only)
NC
Connect to
chasis GND at
one side
ONLY !
PWR +
PWR - DC Output
+
_
+12VDC Power
C - No Charging
N/C - No Charging
Tamper Switch
(In CLOSED
position when
Cabinet Door is
Closed)
RS-485 TR+
RS-485 TR-
RS-485 GND
+ 12V
GND
K 1 K 2 K 3 K 4 K 5 K 6 K 7 K 8 K 9 K 10 K 11 K 12
K 13 K 14 K 15 K 16
J 1 - RS-485
Termination
J 2
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
1
2
3
1
2
3
4
5
6
1
2
3
4
5
6
TMP
GND
PFL
RELAY14 NC
RELAY14 C
RELAY14 NO
RELAY15 NC
RELAY15 C
RELAY15 NO
RELAY12 NC
RELAY12 C
RELAY12 NO
RELAY13 NC
RELAY13 C
RELAY13 NO
0
1 2 3 4 5 6 7 8 9 10 11
D1 D2 D3 D4
D17 D18 D19 D20