Honeywell Ipcam-woc1 User manual

Google Play and the Google Play logo are trademarks of Google Inc.

IPCAM-WOC1 HD Wi- i Outdoor Video Camera

Quick Installation Guide

IPCAM-WOC1 is a 1080p, full HD Wi- i® video camera intended for outdoor use with Honeywell Total Connect® 2.0.

•Camera setup requires a Total Connect® 2.0 account and the Total Connect 2.0 mobile app. Video Services must be enabled in AlarmNet 360™.

•Camera operation requires minimum available bandwidth of 2.1 Mbps.

Package Contents

A. Camera

B. Sun shield

C. Power cable extension [8’ cable]

D. Power adapter with 7’ cable

E. Pig-tail power cable

. Screws and Allen wrench

G. Antenna

a. Bluetooth antenna

b. Not used

c. Reset switch

d. Power

Planning Configuration and Installation

See the other side of this sheet for more about mounting at the installation site

•The camera should be situated within 200 feet (61 m) of a power outlet and within the verified range of its Wi- i® connection. DO NOT mount the

camera within 1 foot (0.3 m) of any other wireless device. Depending on the specifics of your installation, a range extender may be needed to ensure

adequate Wi- i signal strength.

•Pre-installation: It is strongly recommended that camera configuration be done as close as possible to the Wi- i router with which the camera will be

linked. After setup, use a third-party app to check signal strength at the installation site before mounting (over for more information on signal strength.)

•The power adapter must be connected to a non-switchable power outlet.

•Direct sunlight on the camera lens / image sensor may affect picture quality. When placing the camera, consider how the lighting can vary with time of

day and other conditions. The included sun shield can be attached to the camera to help minimize problems with sun glare.

IMPORTANT: Use only ONE of the included power extension cables. This cable adds 8 feet (2.44 m) to the supplied power adapter for a total of 15 feet (4.5 m).

Alternately, you may use the pig-tail power cable to extend the power adapter cable with a maximum of 200 feet (61 m) of 18 AWG wire.

If the included extension cable is not used, you may cut and splice (observing good workmanship) the power transformer cable.

Ensure ro er olarity if the ig-tail ower cable is used. The ig-tail’s black (negative) wire must be connected to the negative (white

dashed) wire on the ower ada ter.

Wi-Fi Configuration and Camera Registration

Download the Total Connect® 2.0 app from the App Store or on Google Play.

(Look for the red Total Connect 2.0 logo.) Note: Significant differences between the

iOS and Android versions of the app are noted in these instructions.

For best results, configure only one camera at a time.

Check these settings when you turn on your mobile device’s Wi-Fi and Bluetooth:

•Make sure the Bluetooth isn’t connected to another device, such as headphones

•Also, make sure the mobile device is NOT on Silent (ringer and speaker should be audible)

a. Verify that the camera’s antenna is firmly connected.

b. Turn on your smart device’s Bluetooth and Wi- i.

c. Launch the app and sign in with your Total Connect® 2.0 account.

d. Plug the power supply into an AC outlet, but:.

DON’T CONNECT THE POWER SUPPLY TO THE CAMERA YET! When you do,

refer to the diagram at right →

→→

→

If your account has more than one Location, select the appropriate one using the

dropdown menu at the top of the screen.

Press CAMERAS at the bottom (iOS) or top (Android) of the screen. (Remember that the

horizontal Navigation Order can be customized in iOS.)

a. At upper right, press ADD CAMERA (iOS) or (Android)

b. Select the type of camera you’re installing. The names of the camera models may

vary from the illustration at right.

c. Name the camera and press NEXT.

d. Connect the power supply to the camera. The LED at the top flashes various colors.

Then, WAIT for the camera’s LED to flash blue only. This may take a couple of minutes.

e. Press NEXT on the app.

a. On the Pair Your Camera screen, press Generate QR Code. After a brief wait, the

code appears.

b. Show the QR code on your device to the camera from 3 – 8 inches away.

If you can, keep an eye on your device’s screen; when the code is scanned

successfully, a confirmation message will appear over the QR code.

The app will also provide audible confirmation via your mobile device’s speaker.

c. Select your Wi- i network and press NEXT.

d. Enter the network password and press NEXT. inal setup begins.

When setup is complete, the LED on the camera changes from steady blue, to purple

and finally to steady green.

The app also displays Setu Successful*. Press DONE or ADD ANOTHER CAMERA.

After setup, go back to the CAMERAS page and check your newly-registered camera.

Touch the review image to launch a live stream from the camera.

*The app will tell you if you need to repeat the setup process. This involves resetting

the camera, which is described in the app itself.

See the other side of this sheet for more information about the required steps.

Resetting the Camera

If setup needs to be repeated, or to connect the camera to a different network, activate the Reset switch as seen at right.

•To reset the connection, press and hold the reset button until the LED on the camera starts blinking white. Release the button

immediately after the LED starts to blink.

•To join a new/different network:

oOn the app’s Cameras screen, press and delete the camera from the link on its settings page.

oPress and hold the Reset switch to reset all settings to their factory defaults

oUnplug the camera and then reconnect it.

oRepeat the registration procedure.

LED STAT S INDICATOR

During installation

Blue, blinking Power on. Ready to start setup.

Blue, steady Connected to the app. Ready to complete setup.

Purple, steady QR code scan is complete. Restart the Wi- i connection process.

Green, blinking

Connecting to Wi- i network.

Red, steady Setup timed out. Unplug the camera, plug it back in and restart setup process.

During o eration

Green, blinking Connecting to Wi- i network.

Green, steady Connected to Wi- i and operating. Note: The camera is always ready to record but only originates live streaming video when the app

calls for a live stream.

Red, blinking Not connected to Wi- i.

Low-light operation is indicated by four red LE s arranged around the lens on the front of the camera.

More about mounting at the installation site

IPCAM-WOC1 can be wall- or ceiling-mounted. The camera can be installed with cables running along the outside of a wall, or inside the wall. or outdoor

installations where cables are exposed to the weather, please protect the cable-ends with an enclosure such as a weatherproof single-gang box, available at

most hardware stores. In any installation, make sure the camera’s antenna is firmly connected.

Checking Wi-Fi signal strength at the site using the app:

•

On the Cameras page, touch for

the camera you’re setting up

(on Android, touch )

•

Select Camera Information >

•

Signal Strength is displayed under

“IP Address”

60 – 100 Optimal

40 – 59 Marginal

00 – 39 Use of a Wi- i range

extender strongly

recommended

Wall mount example

Ceiling mount example

(both shown with weatherproof single-gang box)

FEDERAL COMM NICATIONS COMMISSION & ISED STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or

modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to CC requirements and has been found acceptable for use. The CC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may

cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the

specifications in Part 15 of CC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•If using an indoor antenna, have a quality outdoor antenna installed.

•Reorient the receiving antenna until interference is reduced or eliminated.

•Move the radio or television receiver away from the receiver/control.

•Move the antenna leads away from any wire runs to the receiver/control.

•Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

•Consult the dealer or an experienced radio/TV technician for help.

FCC / ISED STATEMENT

This device complies with Part 15 of the CC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la CC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne

doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

RF EXPOSURE STATEMENT:

The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating

in conjunction with any other antenna or transmitter except in accordance with CC and ISED multi-transmitter product procedures.

MISE EN GARDE EXPOSITION AUX FRÉQUENCES RADIO:

La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être

située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur CC et ISED.

DECLARACIÓN IFETEL

La operación de este equipo está sujeta a las siguientes dos condiciones

1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y

2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada.

DECLARACIÓN ANATEL

Este equipamento opera emcarátersecundário, isto é, nãotemdireito a proteção contra

interferência prejudicial, mesmo de estações do mesmotipo, e

nãopodecausarinterferência a sistemas operando emcaráterprimário.

TRADEMARKS

Honeywell is a registered trademark of Honeywell International Inc.

or online support visit, https://mywebtech.honeywell.com/