Honeywell PRO-2200 User manual

PRO-2200
Power Supply With Battery Backup*
Installation Manual
Part Number: PRO22E1PS
TD1140 rev0401
* 4 amp hour and 7 amp hour backup battery sold separately.

2PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide

PRO-2200 Power Supply With Battery Backup PRO22E1PS 3
Installation Guide
Contents
Warnings and Cautions.........................................................................................4
Disclaimer.............................................................................................................6
Product Liability; Mutual Indemnification...............................................................6
Unpacking Procedure ...........................................................................................6
Shipping Instructions ............................................................................................7
LimitedWarranty ...................................................................................................7
Confidentiality .......................................................................................................8
PRO2200 Enclosure.............................................................................................9
Description............................................................................................................9
Dimensions.........................................................................................................10
Power Supply......................................................................................................10
Notes ..................................................................................................................11
Installation Instructions........................................................................................12
Installation Diagram ............................................................................................13
Cable Specifications...........................................................................................14
NCI Cable Part Numbers ....................................................................................15

4PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Warnings and Cautions
WARNING
Before installation, TURN OFF the external circuit breaker which supplies power to the
system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or deathcould occur, and theequipment could be damagedbeyond repair
if this precaution is not observed!
WARNING
Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator or gate without
providing an alternative exit in accordance with all fire and life safety codes pertinent to
the installation.These fire and safety codes vary from city to city and approval from local
fire officials is required whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most applica-
tions, single action exit without prior knowledge of what to do is a life safety requirement.
Always make certain that any required approvals are obtained in writing.DO NOT AC-
CEPTVERBAL APPROVALS, ASTHEY ARE NOTVALID.
Northern never recommends using thePRO-2200or related products asaprimary warning
or monitoring system. Primary warning or monitoring systems should always meet local
fire and safety code requirements.The installer must test the system on a regular basis
and instruct the end user in appropriate daily testing procedures.Failure to test a system
regularly could make installer liable to the end user for damages if a problem occurs.
WARNING
EARTH groundall enclosures, for proper installation.
EARTH groundcan be obtained throughthe power supply orby groundingthecabinet,
BUTNOT BOTH!
WARNING
Use suppressors on all door strikes.Use S-4 suppressors for installation.Northern
Computers recommends only DC strikes.
The information in this document is subject to change without notice.

PRO-2200 Power Supply With Battery Backup PRO22E1PS 5
Installation Guide
CAUTION
IF ANY DAMAGETOTHE SHIPMENT IS NOTICED, A CLAIM MUST BE FILEDWITH
THERESPONSIBLE COMMERCIAL CARRIER.
CAUTION
Electro-static discharge can damage CMOS integrated circuits and modules.
To prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation.These
workstations consist of a desk mat, floor mat and an ESD wrist strap.Workstations are
available from various vendors.
NOTICE
THIS EQUIPMENT HAS BEENTESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OFTHE FCC RULES
WHEN WIRED USING METAL CONDUIT FORTHE CABLING EXTERNAL TO THE
ENCLOSURE.THESE LIMITS ARE DESIGNEDTO PROVIDE REASONABLE PROTEC-
TION AGAINST HARMFUL INTERFERENCE WHENTHE EQUIPMENT IS OPERATED
IN A COMMERCIAL ENVIRONMENT.THIS EQUIPMENT GENERATES, USES, AND
CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED
IN ACCORDANCE WITHTHE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCETO RADIO COMMUNICATIONS.OPERATION OF THIS EQUIPMENT
IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN
WHICH CASETHE USER WILL BE REQUIREDTO CORRECTTHE INTERFERENCE
AT HIS OWN EXPENSE.
NOTICE
This document and the data in it shall not be duplicated, used or disclosed to others for
procurement or manufacture, except as authorized by and with the written permission of
Northern Computers, Inc.The information contained in this document or in the product
itself is considered the exclusive property and trade secrets of Northern Computers, Inc.
Copyright laws of the United States protect all information in this document or in the
software product itself.
NOTICE
Any use of this product is subject to the terms and acceptance of the Northern
Computers, Inc.Software Agreement.Please request a copy from Northern Computers,
Inc., and review the agreement carefully.

6PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall immediately
notify Northern in writing of all such claims. Northern shall defend or settle such claims
and shall indemnify and hold Customer harmless for any costs or damages including
reasonable attorneys’fees which Customer may be required to pay as a result of the
defective Product or the negligence of Northern, its agents, or its employees.
Customer shall hold harmless and indemnify Northern from and against all claims,
demands, losses and liability arising out of damage to property or injury to persons
occasioned by or in connection with the acts or omissions of Customer and its agents
and employees, and from and against all claims, demands, losses and liability for costs of
fees, including reasonable attorneys’fees, in connection therewith.
Unpacking Procedure
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercialcarrier.
All containers should be opened and unpacked carefully in order to prevent damage to the
contents.
The following steps are used to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all packing materials; it may be used again for reshipment
of the equipment, if needed.
2. Inspect the contents for shortage.If items are missing, contact the order entry
department at 800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
If shipping caused damage to the unit, a claim must be filed with the
commercialcarrier.
If any other defect is apparent, call for a return authorization at 800-323-4576.

PRO-2200 Power Supply With Battery Backup PRO22E1PS 7
Installation Guide
Shipping Instructions
To ship equipment back to Northern Computers,Inc.:
1.Contact the customer servicedepartment beforereturningequipment at 800-323-4576.
Pleasehave the followingavailable when calling:
• A description of the problem or reason equipment is being returned.
• Original purchase order number, invoice number and warranty information - if the
unit is still under warranty.
• A new purchase order number if the unit is not under warranty
2. Obtain the Return Authorization Number (RMA) from the customer service
department.
3.Show the RMA number on all packages shipped.Packages, which are not marked with
an RMA number will be refused at the factory and returned COD.
4.Carefully pack theequipment for shipment. Usethe original packingmaterial whenever
possible.
Limited Warranty
All Products sold or licensed by Northern include a warranty registration card which must
be completed and returned to Northern by or on behalf of the end user in order for
Northern to provide warranty service, repair, credit or exchange. All warranty work shall
behandled through Customerwhich shall notify Northern and applyfora Return
MerchandiseAuthorization(RMA) number priorto returning anyProduct forservice, repair,
credit or exchange. Northern warrants that its Products shall be free from defects in
materials and workmanship for a period of two years from date of shipment of the Prod-
uct to Customer.The warranty onTerminals, Printers, Communications Products and
Upgrade kits is 90 days from date of shipment.Satisfaction of this warranty shall be
limited to repair or replacement of Products which are defective or defective under
normal use.Northern’s warranty shall not extend to any Product which, upon
examination, is determined to be defective as a result of misuse, improper storage,
incorrect installation, operation or maintenance, alteration, modification, accident or
unusual deterioration of the Product due to physical environments in excess of the limits
set forth in Product manuals.THERE ARE NOWARRANTIESWHICH EXTEND BEYOND
THIS PROVISION.THISWARRANTY IS IN LIEU OF ALL OTHERWARRANTIES
WHETHEREXPRESS,IMPLIED OR STATUTORY,INCLUDINGIMPLIEDWARRANTIES
OFMERCHANTABILITY OR FITNESSFOR ANY PARTICULAR PURPOSE.NOREPRE-
SENTATION ORWARRANTY OFTHE DISTRIBUTOR SHALL EXTENDTHE LIABILITY
OR RESPONSIBILITY OFTHE MANUFACTURER BEYONDTHETERMS OFTHIS
PROVISION.IN NO EVENT SHALL NORTHERN BE LIABLE FOR ANY
RE-PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF USE, INCIDENTAL,
CONSEQUENTIALOR SPECIAL DAMAGESTO ANYPERSON RESULTING FROMTHE
USEOFNORTHERN’SPRODUCTS.

8PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other
materials furnished by Northern relating to the design, use and service of Products shall
remainconfidential and shallconstitute proprietary rightsof Northern, andCustomer
agrees to treat such information as confidential.Customer shall acquire no rights in the
design of Products or the related materials except to use such information solely for the
purpose of and only during the time it sells Products. Customer shall not copy the design
of any Products or use or cause to be used any Product design or related materials for its
own benefit or for the benefit of any other party.The covenants contained in this section
shall remain effective throughout the term of this Agreement and thereafter unless specifi-
cally waived by Northern in writing.

PRO-2200 Power Supply With Battery Backup PRO22E1PS 9
Installation Guide
PRO-2200 Enclosure
Description
The PRO22E1PS is a 4 amp power supply with battery backup control.The unit mounts in
the PRO22ENC1, PRO22ENC2 or the PRO22ENC5 by sliding the unit vertically into the
right most card guide.The PRO22E1PS can be wired to the PRO-2200 I/O with the self-
contained cabling.The unit can supply up to 4 amps to the 9 panels used in the PRO-
2200 enclosure system.When used with the PRO22DCC daisy chain for communication
and power distribution, the PRO22E1PS becomes an easy to wire power system.
The PRO22E1PS is capable of supplying a charging current to a 4 amp hour, 7 amp hour
or larger 12VDC sealed battery purchased separately.The powersupply controls inputs
for AC Fail and Battery Fail.There is a Power On light located conveniently near the AC
cord inlet.

10 PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Dimensions
Height: 9"
Width: 5.5"
Depth: 2.2"
Power Supply
• 12VDC 4 amp continuous power limited output with backup battery charging and
batterysupervision
• The power supply is not rated for lock power
• The power supply can accept 85VAC to 230VAC at 50/60 hz
• 110VAC/60 hz .5 amp
• 220VAC/50 hz .25 amp
• Maximumbattery charging current.5 amp
• AC on LED
• AC Fail supervision when connected to PRO22IC or other PRO-2200 I/O at PFL
(Power Fail) input
• Low battery supervision when connected to an auxiliary input
• Short circuit and thermal overload protection with self-resetting poly fuses
• Allpower connections shouldbe madewith 18ga wire orlargerwiring

PRO-2200 Power Supply With Battery Backup PRO22E1PS 11
Installation Guide
NOTES

12 PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Installation Instructions
1. RemovethePRO22E1PS from packagingmaterial.
2. Remove the PRO22E1PL from the plastic bag. Place the LED end into the small
roundhole at thebottom ofthePRO22ENC1 or PRO22ENC2(see diagram).Make
sure that the red LED is to the outside of the enclosure.
3. Remove the PRO22E1PO from the plastic bag. Feed the cable into the square hole at
thebottom of the PRO22ENC1or PRO22ENC2 (see installationdiagram onpage13).
It is important to make sure that the AC inlet will be facing out of the enclosure and
the enclosed power cord will be facing toward the rear when plugged in.Do Not Power
UpThe Supply AtThisTime.
4. Connect the AC Power three prong connector to the PRO22E1PO cable.
5. Connect the Power On light two prong connector to the PRO22E1PL cable.
6. Make sure the remainder of the cables are pulled towards the front of the power
supply and that the AC and Power On light do not bind behind the power supply.Slide
the PRO22E1PS into the right-most card guide.
7. At this time, insure that the power supply is working correctly by the following:
a. Make sure the 12VDC red and black cable ends and battery cables are separated
and not touching any metal.
b. Plug the PRO22E1PS into the supplied power cord and into a wall socket.
c. Check the voltage at the 12VDC power cable to insure it is between 13.6 and
14.0VDC
d. Check the battery cables to insure that they are also between 13.6 and 14.0 VDC.
e. Check that the red Power On LED is lit.
f. UNPLUGTHE POWER SUPPLY ATTHISTIME!!!
8. After disconnecting the power supply from the source, wire the 12VDC to the PRO-
2200 I/O.The red wire is +12VDC and the black wire is -12VDC.Wire all I/O in
parallel.The PRO22DCC is also available as an option.Connect the power supply
cables to the daisy chain and the RS485 communications and the 12VDC power will
be wired for the I/O.See individual panel installation manual for additional details.DO
NOT POWERTHE PANELS UNTIL ALLWIRING IS COMPLETE!
9. Wire the Power Fail cable white wire into the PRO-2200 I/O PFL input and the black
wire into the common for that input.
10. Wire the Battery Fail cable to an auxiliary input and rename the input using front end
softwareWIN PAK PRO Release 3 with service pack 1 or higher.
11. Wirethe grounding cable tothe groundingstud.The enclosure may be groundedusing
the power supply or a separate ground wire, BUT NOT BOTH!
12. Connect the battery cables to the backup battery if required.The red cable connects
to the positive (+) terminal on the battery and the black cable to the negative (-)
terminal of the battery. Connect only the red positive battery cable at this time.
Connect the black negative cable when the power supply is powered up.The battery
may be placed directly in front of the power supply for a 4 amp hour or 7 amp hour
battery.The battery may also be placed above the card rack if wiring allows.

PRO-2200 Power Supply With Battery Backup PRO22E1PS 13
Installation Guide
13. CHECK ALLWIRING BEFORE POWERINGUPTHE PRO22E1PS.Unrepairable
damage could result from improper wiring.Power up the PRO22E1PS.All panels
connected should go through their particular start up sequence.See individual
installation manuals for more detail.
Installation Diagram
Bottom View
Front View

14 PRO-2200 Power Supply With Battery Backup PRO22E1PS
Installation Guide
Cable Specifications
Application NCI Part No. AWG Description Max. Dist. Imp. Cap.
N-485 connections NC2442-TN N/A Belden 9842 4000' (1200 m) 120Ω 12.8pf/ft
N/A or equivalent
CR-1, TR-1, CI-1, KR-1 NC1861-BL 18 6 conductor shielded 500' (152 m)
Wiegand card readers
NR-1 magstripe reader NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-1-280 Cotag reader:
280 read head to SZC NC1861-BL 18 6 conductor shielded 300' (91 m)
SZC to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-2 Hughes reader:
scanner to reader NC1861-BL 18 6 conductor shielded 30' (9 m)
reader to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-3, PR-5 Indala readers:
A-3/A-5 read head to RE-2 NC18121-YL 18 12 conductor shielded 75' (23 m)
RE-2 to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-20 , PR-22 Indala readers:
A-20/A-22 read head
to RE-2 NC18121-YL 18 12 conductor shielded 75' (23 m)
RE-2 to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-10, PR-12 Indala readers: NC1861-BL 18 6 conductor shielded 500' (152 m)
HG-3 hand geometry reader: NC1861-BL 18 6 conductor shielded 500' (152 m)
5 conductor keypad NC1861-BL 18 6 conductor shielded 500' (152 m)
Alarm input points NC 2221-BR 22 2000' (610 m)
Relay outputs NC 1821-OR 18 twisted pair, shielded 2000' (610 m)
NOTE: For Plenum rated cable just add a “P”to Northern’s part number prefix;for example NC1861-BL
becomesPNC1861-BL

PRO-2200 Power Supply With Battery Backup PRO22E1PS 15
Installation Guide
NCI Cable Part Numbers
Part Number Description Application Length
NC1841-GY 18 AWG/4 conductor reader cable 1,000'
NC1861-BL-500 18 AWG/6 conductor reader cable 500'
NC1861-BL 18 AWG/6 conductor reader cable 1,000'
NC18121-YL-500 18 AWG/12 conductor keypad cable 500'
NC18121-YL 18 AWG/12 conductor keypad cable 1,000'
NCNET-1 50 ohm network cable 1,000'
NC2221-BR 22 AWG/2 conductor alarm cable 1,000'
NC1821-OR 18 AWG/2 conductor power/door cable 1,000'
NCC59206-BK RG-59 video cable 1,000'
NCP1841-GY 18 AWG/4 conductor Plenum reader cable 1,000'
NCP1861-BL-500 18 AWG/6 conductor Plenum reader cable 500'
NCP1861-BL 18AWG/6 conductor Plenum reader cable 1,000'
NCP18121-YL 18 AWG/12 conductor Plenum keypad cable 1,000'
NCP18121-YL-500 18 AWG/12 conductor Plenum keypad cable 500'
NCPNET-1 50 ohm Plenum network cable 1,000'
NCP2221-BR 22 AWG/2 conductor Plenum alarm point cable 1,000'
NCP1821-OR 8 AWG/2 conductor Plenum power/door cable 1,000'
NC2442-TN 24 AWG/120Ω12.8pf RS485 wire communication cable 1,000'
NCP2442-TN 24 AWG/120Ω12.8pf RS485 wire communication cable 1,000'

Honeywell Security & Data Collection
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299
[phone]
www.honeywellaccess.com