Honeywell EQUIP Series User manual

2MP/4MP Low Light WDR IP Camera
H4W2GR1V
H3W2GR1V
HBW2GR1V
HCL2GV
H2W2GR1
H4L2GR1V
H3W4GR1V
HBL2GR1V
HCW2GV
H4W4GR1V
HBW2GR3V
User Guide

i
Cautions and Warnings
CAUTION To ensure compliance with electrical safety standards, CSA Certified/UL
Listed LPS or Class 2 power adapters are required. Power over
Ethernet (PoE) shall be
provided by listed information technology equipment
meeting the IEEE 802.3af PoE
standard. The PoE is not intended to be
connected to exposed (outside plant) networks.
CAUTION To comply with EN50130-4 requirements, a UPS should be employed when
powering on the camera from 24 V AC.
CAUTION Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your
warranty.
Regulatory Statements
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Note
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

ii
Manufacturer’s Declaration of Conformity
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-
1.
Europe
The manufacturer declares that the equipment supplied is compliant with the European
Parliament and Council Directive on the Restrictions of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment (2011/65/EU), General Product Safety
Directive (2001/95/EC), and the essential requirements the EMC directive 2004/108/EC,
conforming to the requirements of standards EN 55032 for emissions, EN 50130-4 for
immunity, and EN 60950-1 for electrical equipment safety.
Waste Electrical and Electronic Equipment (WEEE)
Correct Disposal of this Product (applicable in the
European Union and other European countries with
separate collection systems).
This product should be disposed of, at the end of its useful
life, as per applicable local laws, regulations, and
procedures.
Safety Instructions
Before installing or operating the unit, read and follow all instructions. After installation,
retain the safety and operating instructions for future reference.
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
2. INSTALLATION
•Install in accordance with the manufacturer’s instructions.
•Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
•Do not install the unit in an extremely hot or humid location, or in a place subject to
dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to
rain or water may damage the unit.
•Any wall or ceiling mounting of the product should follow the manufacturer’s
instructions and use a mounting kit approved or recommended by the manufacturer.
3. POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
facility, consult your product dealer or local power company.
4. HEAT - Situate away from items that produce heat or are heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers).
5. WATER AND MOISTURE - (Indoor models only) Do not use this unit near water or in an
unprotected outdoor installation, or any area classified as a wet location.

iii
6. MOUNTING SYSTEM - Use only with a mounting system recommended by the
manufacturer, or sold with the product.
7. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer
as they may result in the risk of fire, electric shock, or injury to persons.
8. ACCESSORIES - Only use accessories specified by the manufacturer.
9. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
11. REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric
shock or other hazards. Using replacement parts or accessories other than the original
manufacturers may invalidate the warranty.
12. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to
qualified service personnel under the following conditions:
•When the power supply cord or plug is damaged.
•If liquid has been spilled, or objects have fallen into the unit.
•If the unit has been exposed to rain or water.
•If the unit does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the unit to its normal operation.
•If the unit has been dropped or the enclosure has been damaged.
•When the unit exhibits a distinct change in performance - this indicates a need for
service.
13. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service
technician to perform safety checks to determine that the unit is in proper operating
condition.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty period
Honeywell will repair or replace, at its sole option, free of charge, any defective products
returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service at
1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)
number. Be sure to have the model number, serial number, and the nature of the problem
available for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be
refused.

iv
List of Symbols
The following table contains a list of symbols that may appear on the camera:
Symbol Explanation
The WEEE symbol.
This symbol indicates that when the end-user wishes to discard this product, it
must be sent to separate collection facilities for recovery and recycling. By
separating this product from other household-type waste, the volume of waste
sent to incinerators or landfills will be reduced, and thus natural resources will
be conserved.
The UL compliance logo.
This logo indicates that the product has been tested and is listed by the
Underwriters Laboratories.
The FCC compliance logo.
This logo indicates that the product conforms to Federal Communication’s
Commission compliance standards.
The direct current symbol.
This symbol indicates that the power input/output for the product is direct
current.
The alternating current symbol.
This symbol indicates that the power input/output for the product is
alternating current.
The RCM Compliance symbol.
This symbol indicates that the product conforms with the Australian RCM
guidelines.
The CE Compliance logo.
This logo indicates that the product conforms to the relevant
guidelines/standards for the European Union harmonization legislation.
This symbol is used to direct attention to important information.
The Protective Earth symbol.
This symbol indicates that the marked terminal is intended for connection to
the protective earth/grounding conductor.

v
Contents
About This Document....................................................................................................................................................... viii
Overview of Contents.......................................................................................................................................................... viii
1Accessing the Camera.......................................................................................................................................... 1
Installing the IPC Tool Utility.............................................................................................................................................. 1
Discovering Your Camera on the Network ................................................................................................................... 1
Assigning a New IP Address to Your Camera ............................................................................................................. 1
Upgrading the Camera’s Firmware ................................................................................................................................. 2
Accessing the Camera from a Web Browser ............................................................................................................... 2
2Logging In and Viewing Live Video ................................................................................................................. 4
Logging In to the Web Client ............................................................................................................................................. 4
Overview of the Live Interface............................................................................................................................................ 5
Configuring the Live Interface .......................................................................................................................................... 6
Working in the Live Interface ............................................................................................................................................. 7
Setting Up Live Video Streaming ..................................................................................................................................... 8
Setting the Stream Type ..................................................................................................................................................... 8
Setting the Stream Protocol ............................................................................................................................................. 8
Logging Out of the Web Client.......................................................................................................................................... 8
3Playing Back Recorded Video........................................................................................................................... 9
Overview of the Playback Interface ................................................................................................................................. 9
Playback Controls ................................................................................................................................................................ 9
Video Clip Controls ........................................................................................................................................................... 10
Timeline ............................................................................................................................................................................. 10
Playing Back Recorded Video ......................................................................................................................................... 11
Downloading Recorded Video ........................................................................................................................................ 11
ViewingSnapshots .............................................................................................................................................................. 12
4Configuring Video and Audio Settings........................................................................................................14
Configuring Video Settings.............................................................................................................................................. 14
Configuring Camera Settings ........................................................................................................................................ 14
Managing Profiles ............................................................................................................................................................ 17
Configuring Streaming Settings ................................................................................................................................... 18
Configuring Snapshot Settings .................................................................................................................................... 19
Configuring Privacy Masks ............................................................................................................................................ 20
Configuring the Channel Title ....................................................................................................................................... 21
Configuring the Time Title .............................................................................................................................................. 22
Configuring Customized Text Overlays ...................................................................................................................... 22
Configuring Picture Overlays ........................................................................................................................................ 23
Configuring Regions of Interest ................................................................................................................................... 23
Configuring Zoom and Focus Settings ....................................................................................................................... 23
Configuring Audio Settings ............................................................................................................................................. 24
5Configuring Network Settings........................................................................................................................26
ConfiguringTCP/IP............................................................................................................................................................. 26
IPv4 Address Configuration ........................................................................................................................................... 27
IPv6 Address Configuration ........................................................................................................................................... 27
ARP/Ping ............................................................................................................................................................................. 27
Configuring NetworkConnections............................................................................................................................... 28
ConfiguringONVIF .............................................................................................................................................................. 29

vi
Configuring RSTP................................................................................................................................................................ 29
Configuring PPPoE Settings........................................................................................................................................... 30
Configuring DDNS Settings ............................................................................................................................................ 30
Filtering IP/MAC Addresses ............................................................................................................................................ 31
Adding IP/Mac Addresses to the List of Approved Users ...................................................................................... 32
Editing IP/Mac Addresses ............................................................................................................................................. 32
Deleting IP/Mac Addresses from the List of Approved Users .............................................................................. 33
Configuring Email Settings ............................................................................................................................................. 33
Configuring UPnP Port Mapping.................................................................................................................................. 34
Configuring SNMP Settings............................................................................................................................................ 35
ConfiguringBonjour ........................................................................................................................................................... 36
Configuring Multicast Settings ..................................................................................................................................... 36
Configuring 802.1X Settings .......................................................................................................................................... 37
Configuring QoS Settings ................................................................................................................................................ 37
Working with Certificates.................................................................................................................................................. 38
Importing Certificates................................................................................................................................................. 38
Certificate Request....................................................................................................................................................... 39
6Configuring Event Settings.............................................................................................................................40
Configuring Alarm Events ................................................................................................................................................ 40
Configuring System Events ............................................................................................................................................. 42
Configuring SD Card Event Settings ........................................................................................................................... 42
Configuring Network Event Settings ........................................................................................................................... 42
Configuring Illegal Access Event Settings ................................................................................................................. 43
Configuring Motion Detection Events........................................................................................................................ 44
Configuring Camera Tampering Events .................................................................................................................... 46
Configuring Scene Change Events .............................................................................................................................. 47
Configuring Audio Events ................................................................................................................................................ 48
Configuring Smart Plan.................................................................................................................................................... 49
Configuring IVS Analysis Events .................................................................................................................................. 50
Configuring Face Detection Events............................................................................................................................. 51
Configuring People Counting Events........................................................................................................................ 52
People Counting............................................................................................................................................................ 52
Report ................................................................................................................................................................................. 53
Configuring Heat Map Events....................................................................................................................................... 54
7Intelligent Analytics System ...........................................................................................................................55
8Configuring Recording Settings....................................................................................................................56
Configuring RecordingSchedules ............................................................................................................................... 56
Configuring Storage Settings......................................................................................................................................... 57
Configuring Storage Paths ............................................................................................................................................ 57
Configuring the Local SD Card for Storage ............................................................................................................... 58
Configuring an FTP Server for Storage ....................................................................................................................... 58
Configuring an NAS Disk for Storage .......................................................................................................................... 59
Configuring Recording Settings.................................................................................................................................... 59
9Configuring System Settings..........................................................................................................................61
Configuring General System Settings ........................................................................................................................ 61
Configuring Date and Time Settings........................................................................................................................... 61
Changing the Date and Time Format ......................................................................................................................... 62
SettingtheDateandTime ............................................................................................................................................... 62
Configuring AccountSettings........................................................................................................................................ 63
Managing Groups ............................................................................................................................................................. 63
Managing Users ................................................................................................................................................................ 65

vii
Resetting the Camera......................................................................................................................................................... 67
Backing Up/Restoring a Configuration ..................................................................................................................... 68
Configuring Maintenance Settings ............................................................................................................................. 68
Upgrading the Firmware ................................................................................................................................................... 69
Viewing Version Information ........................................................................................................................................... 69
Managing Logs ..................................................................................................................................................................... 70
Viewing Logs ...................................................................................................................................................................... 70
Backing Up Logs ............................................................................................................................................................... 71
Deleting Logs ..................................................................................................................................................................... 71
Viewing Online Users.......................................................................................................................................................... 71
10 Appendix A Technical Specifications...........................................................................................................73
HBW2GR3V/HBW2GR1V/HBL2GR1V Bullet Camera...................................................................................... 73
HCL2GV/HCW2GV Box Camera .................................................................................................................................. 76
H3W2GR1V/H3W4GR1V Indoor Dome Camera.................................................................................................. 79
H4W2GR1V/H4L2GR1V/H4W4GR1V Outdoor Dome Camera ................................................................... 82
H2W2GR1 Micro Dome Camera .................................................................................................................................. 84

About This Document
This manual is intended for system installers, administrators, and users of Honeywell’s equIP®
Series 2MP/4MP LOW LIGHT WDR IP cameras and contains instructions for accessing,
configuring, and operating the cameras.
Overview of Contents
This manual contains the following chapters and appendixes:
•Chapter 1, Accessing the Camera, describes how to access the camera remotely from a web
browser.
•Chapter 2, Logging In and Viewing Live Video, describes how to log in to the camera and how
to use the Live interface.
•Chapter 3, Playing Back Recorded Video, describes how to play back and export recorded
video and snapshots.
•Chapter 4, Configuring Video and Audio Settings, describes how to set up video and audio
streams.
•Chapter 5, Configuring Network Settings, describes how to set up the camera on a network.
(For advanced users only.)
•Chapter 6, Configuring Event Settings, provides instructions for configuring alarm
inputs/outputs, motion detection, audio detection, tampering detection, and system event
settings.
•Chapter 7, Intelligent Analytics System, describes how to access the Intelligent Analytics
System.
•Chapter 8, Configuring Recording Settings, describes how to set up a recording schedule
and how to manage recording and storage settings.
•Chapter 9, Configuring System Settings, provides instructions for configuring language and
date and time options, managing user accounts and permissions, setting maintenance
tasks, upgrading firmware, and resetting a camera to its factory defaults.
•Chapter 10, Appendix A Technical Specifications, lists camera specifications.

Accessing the Camera
1
1Accessing the Camera
This chapter contains the following sections:
•Installing the IPC Tool Utility, page 1
•Discovering Your Camera on the Network, page 1
•Assigning a New IP Address to Your Camera, page 1
•Upgrading the Camera’s Firmware, page 2
•Accessing the Camera from a Web Browser, page 2
Installing the IPC Tool Utility
To install the IPC Tool utility and create a desktop shortcut:
1. Insert the included Software and Document disc into your PC’s disc drive.
2. Install the IPC Tool utility to your PC. The shortcut is added to the desktop.
Discovering Your Camera on the Network
To discover your network camera(s), open the IPC Tool utility , enter your user name and
password, and then click Connect. Cameras that are online have a green connected icon
next to them. Cameras that are offline have a gray X next to them. To refresh the list, click
Refresh.
Assigning a New IP Address to Your Camera
The current IP address of your camera appears in the IP column of the devices list. If you want,
you can assign a new static IP address to the camera.
To change the IP address of a single camera:
1. Select the camera that you want to configure from the devices list.

2MP/4MP Low Light WDR IP Camera User Guide
2
2. Click the Network tab.
3. Clear the DHCP check box.
4. Enter the new IP settings in the IP Address, Subnet Mask, and Default Gateway fields.
5. Click Apply to apply the settings.
To change the IP addresses of multiple cameras at the same time:
1. In the left-most pane of the IPC Tool utility, click Batch Setting.
2. Select all of the cameras that you want to configure from the devices list.
3. Click the Network tab.
4. Do one of the following:
•To assign dynamic IP addresses, select the Set all to DHCP check box, and then click
Apply.
•To assign static IP addresses, enter the settings in IP Range, Subnet Mask, and
Default Gateway fields, and then click Apply.
Upgrading the Camera’s Firmware
Before you begin using your camera, make sure you have the latest firmware installed. You
can upgrade a single camera or multiple cameras at the same time.
To upgrade a single camera:
1. Select the camera that you want to upgrade from the devices list.
2. Click the Upgrade tab.
3. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file,
and then click Open. The firmware file appears in the Target File field.
4. Click Upgrade. When the upgrade is complete, the camera will reboot.
To upgrade multiple cameras at the same time:
1. In the left-most pane of the IPC Tool utility, click Batch Setting.
2. Select all of the cameras that you want to upgrade from the devices list.
3. Click the Upgrade tab.
4. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file,
and then click Open. The firmware file appears in the Target File field.
5. Click Upgrade. When the upgrade is complete, the cameras will reboot.
Accessing the Camera from a Web Browser
To access the camera from a web browser:
1. Select the camera that you want to access from the devices list. The camera must be
online .

Accessing the Camera
3
2. On the Device Information tab, click Web Page. The web client opens in your default
browser.

2MP/4MP Low Light WDR IP Camera User Guide
4
2Logging In and Viewing Live Video
This chapter contains the following sections:
•Logging In to the Web Client, page 4
•Overview of the Live Interface, page 5
•Configuring the Live Interface, page 6
•Working in the Live Interface, page 7
•Setting Up Live Video Streaming, page 8
•Logging Out of the Web Client, page 8
Logging In to the Web Client
If this is your first time logging in to the web client, on the login page, enter the default user
name (admin) and password (1234), and then click Login.
For security purposes, you are required to create a new secure password.

Logging In and Viewing Live Video
5
The password must be at least 8 characters long and contain at least one lowercase letter,
one number, and one special character. The password cannot be blank.
Overview of the Live Interface
The following figure shows the layout of the web client’s Live interface.
Figure 2-1 Live Interface

2MP/4MP Low Light WDR IP Camera User Guide
6
Configuring the Live Interface
Note The first time you log into the web client, follow the on-screen
instructions to download and install the web browser plug-in.
You can configure the Live interface using the configuration controls located in the lower left
corner of the screen, immediately below the video window.
Figure 2-2 Live Configuration Toolbar
Table 2-1 Live Configuration Controls
Image
Adjustment
Opens the Image Adjustment panel.
Move the sliders to adjust the image
brightness, contrast, hue, or
saturation. Click the – and + signs to
make fine adjustments. To restore the
settings to their default values (64),
click Reset.
Note These settings only apply to the client end. To change
the settings at the camera end, go to Setup

Camera
Setup Conditions Picture.
Original Size Displays the video at actual size (the exact dimensions are
determined by the stream resolution).
Full Screen Displays the video in full-screen mode. Double-click (or
press Esc) to exit full-screen mode.
Width:Height
Ratio
Displays the video in its original size (Original) or fitted to
your screen (Adaptive).
Fluency Sets the video fluency level (Realtime, Normal, or Fluency).
Select a fluency level based on the capabilities of your
network.
For example, if your connection is slow, selecting Fluency
will prioritize smoothness over image quality.
Rules Info Tracks movement in the video window when intelligent
video surveillance (IVS) is enabled.

Logging In and Viewing Live Video
7
Zoom and
Focus
Opens the Zoom and Focus panel.
Move the sliders to adjust the zoom
and focus settings. Click the – and +
signs to make fine adjustments. The
Step number determines the
magnitude of the adjustment. To set
the focus automatically, click Auto
Focus. To restore the default zoom
and focus settings, click Restore All.
To focus on a specific region, click
Regional Focus, and then drag your
mouse over the area in the video
window.
Working in the Live Interface
The toolbar in the upper left corner of the screen, immediately above the video window,
provides quick access to commonly used controls.
Figure 2-3 Quick Access Toolbar
Table 2-2 Quick Access Controls
Talk Click to enable or disable bidirectional talk (audio must
also be enabled).
Audio Click to enable or disable the audio input stream.
Easy Focus Displays the current video definition (AF Peak) and target
video definition (AF Max). For auto focus to work, the AF
Peak and AF Max values must be close together. If the
values are far apart, the camera must be re-aimed or
focused manually.
Record Click to start or stop recording video. The icon appears red
when video is being recorded, gray when video is not being
recorded.
The recorded video is saved to the location specified in
Setup

Storage Setup

Destination

Path

Live
Record.
Triple
Snapshot
Click to take three snapshots in quick succession (1 per
second). The snapshots are saved to the location specified
in Setup

Storage Setup

Destination

Path

Live
Snapshot.
Snapshot Click to take a snapshot of the current video. The snapshot
is saved to the location specified in Setup

Storage
Setup Destination Path Live Snapshot.
Digital Zoom When this function is enabled, you can drag your mouse
over an area of the video to enlarge that area. Right-click to
return to the previous magnification.

2MP/4MP Low Light WDR IP Camera User Guide
8
Alarm Output Click to generate or cancel an alarm output. The icon
appears red when the alarm is active, gray when the alarm
is inactive.
Help Displays online help for the Live interface.
Setting Up Live Video Streaming
In the upper right corner of the screen, immediately above the video window, you can set the
stream type and protocol for live video streaming.
Setting the Stream Type
To set the stream type, in the Stream Type list, select Main Stream, Sub Stream 1, or Sub
Stream 2.
Main Stream
Delivers
high definition video for real-time monitoring, recording, and
storage. Uses the most bandwidth.
Sub Stream 1
Delivers
low/standard definition video, typically for remote monitoring
in lower network bandwidth environments.
Sub Stream 2
Delivers low, standard, or high definition video.
The properties for each stream type are configured on the Setup > Compression Setup >
Video page (see Configuring Streaming Settings on page 18).
Setting the Stream Protocol
To set the stream protocol, in the Protocol list, select TCP, UDP, or Multicast.
TCP
Provides
most reliable data transmission. Higher latency and bandwidth
use than UDP.
UDP
Provides
fastest data transmission. Lower latency and bandwidth use
than TCP but allows some data loss (such as dropped frames).
Multicast
Provides
the most efficient use of bandwidth if large numbers of clients
are viewing the video simultaneously.
Logging Out of the Web Client
To log out of the web client, in the upper right corner of the screen, click Logout.