Honeywell HD3UH User manual

Document 800-20541V2 – Rev A – 06/2015
Configuration Guide
HD3UH(X)/HD4UH(X)
960H Ultra Wide Dynamic
Minidome Cameras
HD3UH HD3UHX
HD4UH HD4UHX

2
Revisions
Issue Date Revisions
A 06/2015 Updated from 800-20541. Corrected some Specifications,
including temperatures, minimum illumination, AES range,
power consumption, and construction materials.
V2 Rev
A
06/2015 Updated from 800-20541V1. Corrected storage and
operating temperatures. Added digital zoom and horizontal
angle of view specifications. Removed Ext LED Setting and
Smart IR Setting sections.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
DO NOT OPEN
RISK OF ELECTRIC SHOCK

3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Programming the Camera . . . . . . . . . . . . . . . . . . . . . . 7
Exposure Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Exposure Lens Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Exposure Backlight Settings . . . . . . . . . . . . . . . . . . . . . . . . 10
DRC (Dynamic Range Compressor) Setting . . . . . . . . . . . . . . . . 12
Defog Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AGC (Auto Gain Control) Setting . . . . . . . . . . . . . . . . . . . . . . 13
Sense-up Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3D DNR (Digital Noise Reduction) Setting . . . . . . . . . . . . . . . . . 14
Color Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
White Balance Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Day&Night Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
D&N Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
D&N Control Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Delay Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sharpness Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Gamma Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mirror and Flip Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D-Zoom (Digital Zoom) Setting . . . . . . . . . . . . . . . . . . . . . . . 19

4
Motion Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Enabling Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . 20
Privacy Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setting a Privacy Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Communication Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 24
View Angle Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Special Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Initial Setting (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . 26
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SAVE&EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
EXIT (Without Saving) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

5
Introduction 1
This document provides instructions for configuring the 960H Ultra Wide Dynamic
HD3UH(X)/HD4UH(X) minidome camera settings. These instructions are intended for
system installers, administrators, and operators. For information about installing the
camera, refer to the appropriate Quick Installation Guide for your camera.
Use the following sections to configure and use your 960H Ultra Wide Dynamic Minidome
Camera:
•OSD Menu, page 6, for an overview of the OSD menus and settings.
•Programming the Camera, page 7, for information on navigating the OSD menus and
configuring the camera settings.
•Troubleshooting, page 27, for some camera troubleshooting tips.
•Specifications, page 28, for a list of HD3UH(X)/HD4UH(X) specifications.

6
OSD Menu
The camera has
the following OSD
menu structure:

7
Programming the Camera 1
The camera is programmed using the on-screen display (OSD) menus. You can connect a
portable monitor during installation using the supplied adapter cable.
To show the OSD main menu, press the OSD controller
joystick located on the camera control board.
Move the joystick up or down to navigate through the
menu options. Move the joystick right to change a
menu setting.
When a menu option or setting is followed by and
arrow symbol (), press the joystick to access the next
screen. To go back to the main menu, select RETURN
or EXIT JUMP, and then press the joystick.
Exposure Menu
Exposure Lens Settings
Select DC or MANUAL. Press the OSD controller joystick to select and set the various
parameters.
UP
DOWN
RIGHTLEFT

8
DC Lens
INDOOR/OUTDOOR: Select for the appropriate lighting condition.
BRIGHTNESS: Select according to the brightness of the surroundings.
SHUTTER: Select AUTO, MANUAL SHUTTER, or FLC.
FOCUS ADJUST
AUTO Set to 1/60 (1/50)
MANUAL SHUTTER Select from 1/60 (1/50) to 1/60000.
FLC Flickerless. Select if the camera image has some flickering.
When ON, the default level is
set automatically by the
controlling lens, depending on
the installation circumstances.

9
Manual Lens
INDOOR/OUTDOOR: Select for the appropriate lighting condition.
BRIGHTNESS: Select according to the brightness of the surroundings.
SHUTTER: Select AUTO, MANUAL SHUTTER, or FLC.
FOCUS ADJUST
AUTO Set to 1/60 (1/50)
MANUAL SHUTTER Select from 1/60 (1/50) to 1/60000.
FLC Flickerless. Select if the camera image has some flickering.
When ON, the default level is
set automatically by the
controlling lens, depending on
the installation circumstances.

10
Exposure Backlight Settings
Select HME, BLC or WDR. Press the OSD controller joystick to select and set the various
parameters.
HME Backlight
HME (Highlight Mask Exposure) allows objects to appear clearly by masking the extremely
bright areas on the screen.
Select HME from the BACKLIGHT setting to turn on HME. Then configure the available
parameters.
BLC Backlight Compensation
LEVEL Use the slider to select an HME level from 0to 20. The lower the setting, the darker the HME
mask will be on the screen.
MODE ALL DAY: Select to run HME all the time.
NIGHT ONLY: Select to only run HME at night (B/W mode only).