Honeywell HEIPTZ-2736-WI User manual

HEIPTZ-2736-WI
Explosion-Proof PTZ Camera
User Manual

User Manual of Network Explosion-Proof PTZ Camera
i
About this Manual
This Manual is applicable to Explosion-Proof PTZ Camera.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all
other information hereinafter are for description and explanation only. The information contained in
the Manual is subject to change, without notice, due to firmware updates or other reasons.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards
listed under the Low Voltage Directive 2015/35/EU, the EMC Directive 2014/30/EU,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance

User Manual of Explosion-Proof PTZ Camera
ii
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid
danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to prevent
serious injury or death.
Cautions Follow these precautions to prevent
potential injury or material damage.
Warnings:
Adopt the power adapter which can meet the safety extra low voltage (SELV) standard. The
power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may cause
over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used product to rain or
moisture.
This installation should be made by a qualified service person and should conform to all the
local codes.
Install blackouts equipment into the power supply circuit for convenient supply interruption.
If the product does not work properly, contact your dealer or the nearest service center.
Never attempt to disassemble the product yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions:
If the Explosion-Proof PTZ Camera fails to synchronize local time with that of the network,
you need to set up Explosion-Proof PTZ Camera time manually. Visit the Explosion-Proof PTZ
Camera (via web browser or client software) and enter system settings interface for time
settings.
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product on

User Manual of Explosion-Proof PTZ Camera
iii
vibratory surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can
cause fatal damage to the product.
The sensor may be burned out by a laser beam, so when any laser equipment is being used,
make sure that the surface of the sensor not be exposed to the laser beam.
For working temperature, refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
While shipping, the product should be packed in its original packing.
Use the provided glove when open up the product cover. Do not touch the product cover
with fingers directly, because the acidic sweat of the fingers may erode the surface coating of
the product cover.
Use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do not
use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion. Use the
manufacturer recommended battery type.

User Manual of Explosion-Proof PTZ Camera
iv
Table of Contents
CHAPTER 1 OVERVIEW .................................................................................................................1
1.1 SYSTEM REQUIREMENT .............................................................................................................1
1.2 FUNCTIONS............................................................................................................................1
CHAPTER 2 NETWORK CONNECTION ............................................................................................4
2.1 SETTING THE EXPLOSION-PROOF PTZ CAMERA OVER THE LAN...........................................................4
2.1.1 Wiring over the LAN .......................................................................................................4
2.1.2 Activating the Explosion-Proof PTZ Camera .....................................................................5
2.1.3 (Optional) Setting Security Question................................................................................6
2.2 SETTING THE EXPLOSION-PROOF PTZ CAMERA OVER THE WAN .........................................................7
2.2.1 Static IP Connection ........................................................................................................7
2.2.2 Dynamic IP Connection ...................................................................................................8
CHAPTER 3 ACCESSING TO THE EXPLOSION-PROOF PTZ CAMERA............................................... 10
3.1 ACCESSING BY WEB BROWSERS ................................................................................................10
CHAPTER 4 BASIC OPERATIONS ..................................................................................................12
4.1 POWER-UP ACTION ............................................................................................................... 12
4.2 CONFIGURING LOCAL PARAMETERS ............................................................................................12
4.3 LIVE VIEW PAGE .................................................................................................................... 13
4.4 STARTING LIVE VIEW .............................................................................................................. 14
4.5 OPERATING PTZ CONTROL ......................................................................................................16
4.5.1 PTZ Control Panel..........................................................................................................17
4.5.2 Auxiliary Functions........................................................................................................18
4.5.3 Setting/Calling a Preset.................................................................................................20
4.5.4 Setting/Calling a Patrol.................................................................................................22
4.5.5 One-touch Patrol...........................................................................................................23
4.5.6 Setting/Calling a Pattern...............................................................................................24
4.6 PLAYBACK............................................................................................................................25
4.6.1 Play Back Video Files ....................................................................................................25
4.6.2 Downloading Video Files............................................................................................... 27
4.7 PICTURES ............................................................................................................................ 27
CHAPTER 5 SYSTEM CONFIGURATION.........................................................................................29
5.1 STORAGE SETTINGS................................................................................................................ 29
5.1.1 Configuring Recording Schedule ....................................................................................29
5.1.2 Configuring Capture Schedule .......................................................................................31
5.1.3 Configuring Net HDD .................................................................................................... 32
5.2 BASIC EVENT CONFIGURATION .................................................................................................. 35
5.2.1 Configuring Motion Detection .......................................................................................35
5.2.2 Configuring Video Tampering Alarm..............................................................................40
5.2.3 Configuring Video Loss..................................................................................................41
5.2.4 Configuring Alarm Input................................................................................................42

User Manual of Explosion-Proof PTZ Camera
v
5.2.5 Configuring Alarm Output............................................................................................. 44
5.2.6 Handling Exception .......................................................................................................45
5.3 SMART EVENT CONFIGURATION ................................................................................................45
5.3.1 Detecting Audio Exception ............................................................................................46
5.3.2 Configuring Face Detection ........................................................................................... 47
5.3.3 Configuring Intrusion Detection..................................................................................... 47
5.3.4 Configuring Line Crossing Detection ..............................................................................49
5.3.5 Configuring Region Entrance Detection .........................................................................50
5.3.6 Configuring Region Exiting Detection ............................................................................51
5.4 PTZ CONFIGURATION .............................................................................................................53
5.4.1 Configuring Basic PTZ Parameters .................................................................................53
5.4.2 Configuring PTZ Limits .................................................................................................. 54
5.4.3 Configuring Initial Position ............................................................................................55
5.4.4 Configuring Park Actions...............................................................................................56
5.4.5 Configuring Privacy Mask.............................................................................................. 57
5.4.6 Configuring Scheduled Tasks .........................................................................................58
5.4.7 Clearing PTZ Configurations ..........................................................................................59
5.4.8 Configuring Smart Tracking...........................................................................................60
5.4.9 Prioritize PTZ.................................................................................................................61
5.4.10 Position Settings .......................................................................................................61
CHAPTER 6 EXPLOSION-PROOF PTZ CAMERA CONFIGURATION.................................................. 63
6.1 CONFIGURING NETWORK SETTINGS ........................................................................................... 63
6.1.1 Basic Settings................................................................................................................63
6.1.2 Advanced Settings.........................................................................................................67
6.2 CONFIGURING VIDEO AND AUDIO SETTINGS .................................................................................77
6.2.1 Configuring Video Settings............................................................................................77
6.2.2 Configuring Audio Settings............................................................................................79
6.2.3 Configuring ROI Settings ...............................................................................................79
6.2.4 Display Info. on Stream .................................................................................................81
6.3 CONFIGURING IMAGE SETTINGS ................................................................................................81
6.3.1 Configuring Display Settings..........................................................................................81
6.3.2 Configuring OSD Settings .............................................................................................. 87
6.3.3 Configuring Text Overlay Settings ..................................................................................89
6.3.4 Configuring Image Parameters Switch........................................................................... 89
6.4 CONFIGURING SYSTEM SETTINGS...............................................................................................90
6.4.1 System Settings.............................................................................................................90
6.4.2 Maintenance ................................................................................................................95
6.4.3 Security ........................................................................................................................98
6.4.4 User Management...................................................................................................... 100

User Manual of Network Explosion-Proof PTZ Camera
1
Chapter 1 Overview
1.1 System Requirement
System requirement of web browser accessing is as follows:
Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server
2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024 × 768 resolution or higher
Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version,
Mozilla Firefox 5 and above version and Google Chrome 18 and above versions.
1.2 Functions
The functions vary depending on different Explosion-Proof PTZ Camera models.
PTZ Limits
The Explosion-Proof PTZ Camera can be programmed to move within the PTZ limits (left/right,
up/down).
Scan Modes
The Explosion-Proof PTZ Camera provides 5 scan modes: auto scan, tilt scan, frame scan, random
scan and panorama scan.
Presets
A preset is a predefined image position. When the preset is called, the Explosion-Proof PTZ
Camera will automatically move to the defined position. The presets can be added, modified,
deleted and called.
Label Display
The on-screen label of the preset title, azimuth/elevation, zoom, time and Explosion-Proof PTZ
Camera name can be displayed on the monitor. The displays of time and Explosion-Proof PTZ
Camera name can be programmed.
Auto Flips
In manual tracking mode, when a target object goes directly beneath the Explosion-Proof PTZ
Camera, the video will automatically flips 180 degrees in horizontal direction to maintain
continuity of tracking. This function can also be realized by auto mirror image depending on
different Explosion-Proof PTZ Camera models.
Privacy Mask
This function allows you to block or mask certain area of a scene, for preventing the personal
privacy from recording or live viewing. A masked area will move with pan and tilt functions and
automatically adjust in size as the lens zooms telephoto and wide.

User Manual of Explosion-Proof PTZ Camera
2
3D Positioning
In the client software, use the left key of mouse to click on the desired position in the video
image and drag a rectangle area in the lower right direction, then the Explosion-Proof PTZ
Camera will move the position to the center and allow the rectangle area to zoom in. Use the left
key of mouse to drag a rectangle area in the upper left direction to move the position to the
center and allow the rectangle area to zoom out.
Proportional Pan/Tilt
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds according to the
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower than at wide
zoom settings. This keeps the image from moving too fast on the live view image when there is a
large amount of zoom.
Auto Focus
The auto focus enables the Explosion-Proof PTZ Camera to focus automatically to maintain clear
video images.
Day/Night Auto Switch
The Explosion-Proof PTZ Camera delivers color images during the day. And as light diminishes at
night, the Explosion-Proof PTZ Camera switch to night mode and deliver black and white images
with high quality.
Slow Shutter
In slow shutter mode, the shutter speed will automatically slow down in low illumination
conditions to maintain clear video images by extending the exposure time. The feature can be
enabled or disabled.
Backlight Compensation (BLC)
If you focus on an object against strong backlight, the object will be too dark to be seen clearly.
The BLC (Backlight Compensation) function can compensate light to the object in the front to
make it clear, but this causes the over-exposure of the background where the light is strong.
Wide Dynamic Range (WDR)
The wide dynamic range (WDR) function helps the Explosion-Proof PTZ Camera provide clear
images even under back light circumstances. When there are both very bright and very dark areas
simultaneously in the field of view, WDR balances the brightness level of the whole image and
provide clear images with details.
White Balance (WB)
White balance can remove the unrealistic color casts. White balance is the white rendition
function of the Explosion-Proof PTZ Camera to adjust the color temperature according to the
environment automatically.
Patrol
A patrol is a memorized series of pre-defined preset function. The scanning speed between two
presets and the dwell time at the preset are programmable.
Pattern
A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default the focus and
iris are in auto status during the pattern is being memorized.
Power Off Memory
The Explosion-Proof PTZ Camera supports the power off memory capability with the predefined
resume time. It allows the Explosion-Proof PTZ Camera to resume its previous position after

User Manual of Explosion-Proof PTZ Camera
3
power is restored.
Scheduled Task
A time task is a preconfigured action that can be performed automatically at a specific date and
time. The programmable actions include: auto scan, random scan, patrol 1-8 ,pattern 1-4, preset
1-8,frame scan, panorama scan, tilt scan, day, night, reboot, PT adjust, Aux Output, etc.
Park Action
This feature allows the Explosion-Proof PTZ Camera to start a predefined action automatically
after a period of inactivity.
User Management
The Explosion-Proof PTZ Camera allows you to edit users with different levels of permission, in
the admin login status. Multiple users are allowed to access and control the same Explosion-Proof
PTZ Camera via network simultaneously.
3D Digital Noise Reduction
Comparing with the general 2D digital noise reduction, the 3D digital noise reduction function
processes the noise between two frames besides processing the noise in one frame. The noise
will be much less and the video will be clearer.

User Manual of Network Explosion-Proof PTZ Camera
4
Chapter 2 Network Connection
You shall acknowledge that the use of the product with Internet access might be under
network security risks. For avoidance of any network attacks and information leakage,
strengthen your own protection. If the product does not work properly, contact with your
dealer or the nearest service center.
To ensure the network security of the Explosion-Proof PTZ Camera, we recommend you to
have the Explosion-Proof PTZ Camera assessed and maintained termly. You can contact us if
you need such service.
Before you start:
If you want to set the Explosion-Proof PTZ Camera via a LAN (Local Area Network), refer to
Section 2.1 Setting the Explosion-Proof PTZ Camera over the LAN.
If you want to set the Explosion-Proof PTZ Camera via a WAN (Wide Area Network), refer to
Section 2.2 Setting the Explosion-Proof PTZ Camera over the WAN.
2.1 Setting the Explosion-Proof PTZ Camera over the
LAN
Purpose:
To view and configure the Explosion-Proof PTZ Camera via a LAN, you need to connect the
Explosion-Proof PTZ Camera in the same subnet with your computer, and install the SADP or
client software to search and change the IP of the Explosion-Proof PTZ Camera.
For the detailed introduction of SADP, refer to Appendix.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a Explosion-Proof PTZ Camera
and a computer:
Purpose:
To test the Explosion-Proof PTZ Camera, you can directly connect the Explosion-Proof PTZ
Camera to the computer with a network cable as shown in Figure 2-1.
Refer to the Figure 2-2 to set the Explosion-Proof PTZ Camera over the LAN via a switch or a
router.

User Manual of Explosion-Proof PTZ Camera
5
Network Cable
Network Positioning System
Computer
Figure 2-1 Connecting Directly
网络交换机
Network Cable
Network Cable
or
Network Positioning System Computer
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Activating the Explosion-Proof PTZ Camera
Purpose:
You are required to activate the Explosion-Proof PTZ Camera first before you can use the
Explosion-Proof PTZ Camera.
Activation via web browser, activation via SADP, and activation via client software are supported.
Activation via Web Browser
Steps:
1. Power on the Explosion-Proof PTZ Camera, and connect it to the network.
2. Input the IP address into the address bar of the web browser, and enter the activation
interface.
The default IP address of the Explosion-Proof PTZ Camera is 192.168.1.64.

User Manual of Explosion-Proof PTZ Camera
6
Figure 2-3 Activation Interface (Web)
3. Create a password and input the password into the password field.
For your privacy and to better protect your system against security risks, we strongly
recommend the use of strong passwords for all functions and network devices. The
password should be something of your own choosing (using a minimum of 8 characters,
including upper case letters, lower case letters, numbers and special characters) in order
to increase the security of your product.
Proper configuration of all passwords and other security settings is the responsibility of
the installer and/or end-user.
4. Confirm the password.
5. Click OK to activate the Explosion-Proof PTZ Camera and enter the live view interface.
2.1.3 (Optional) Setting Security Question
Security question is used to reset the admin password when admin user forgets the password.
Admin user can follow the pop-up window to complete security question settings during
Explosion-Proof PTZ Camera activation. Or, admin user can go to User Management interface to
set up the function.

User Manual of Explosion-Proof PTZ Camera
7
2.2 Setting the Explosion-Proof PTZ Camera over the
WAN
Purpose:
This section explains how to connect the Explosion-Proof PTZ Camera to the WAN with a static IP
or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can
connect the Explosion-Proof PTZ Camera via a router or connect it to the WAN directly.
Connecting the Explosion-Proof PTZ Camera via a router
Steps:
1. Connect the Explosion-Proof PTZ Camera to the router.
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed
IP address configuration of the Explosion-Proof PTZ Camera.
3. Save the static IP in the router.
4. Set port mapping, E.g., 80, 8000 and 554 ports. The steps for port mapping vary depending
on different routers. Call the router manufacturer for assistance with port mapping.
5. Visit the Explosion-Proof PTZ Camera through a web browser or the client software over the
internet.
Network
Positioning System
Network
Cable
Router with Static IP
PC
Network
Cable
Network
Cable
Internet
Figure 2-4 Accessing the Explosion-Proof PTZ Camera through Router with Static IP
Connecting the Explosion-Proof PTZ Camera with static IP directly
You can also save the static IP address in the Explosion-Proof PTZ Camera and directly connect it
to the internet without using a router. Refer to Section 2.1.2 for detailed IP address configuration
of the Explosion-Proof PTZ Camera.

User Manual of Explosion-Proof PTZ Camera
8
Network
Positioning System
PC
Network
Cable
Network
Cable
Internet
Figure 2-5 Accessing the Explosion-Proof PTZ Camera with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Apply a dynamic IP from an ISP. With the dynamic IP address, you can connect the
Explosion-Proof PTZ Camera to a modem or a router.
Connecting the Explosion-Proof PTZ Camera via a router
Steps:
1. Connect the Explosion-Proof PTZ Camera to the router.
2. In the Explosion-Proof PTZ Camera, assign a LAN IP address, the subnet mask and the
gateway. Refer to Section 2.1.2 for detailed LAN configuration.
3. In the router, set the PPPoE user name, password and confirm the password.
For your privacy and to better protect your system against security risks, we strongly
recommend the use of strong passwords for all functions and network devices. The
password should be something of your own choosing (using a minimum of 8 characters,
including upper case letters, lower case letters, numbers and special characters) in order
to increase the security of your product.
Proper configuration of all passwords and other security settings is the responsibility of
the installer and/or end-user.
4. Set port mapping. E.g. 80, 8000 and 554 ports. The steps for port mapping vary depending on
different routers. Call the router manufacturer for assistance with port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the Explosion-Proof PTZ Camera via the applied domain name.
Connecting the Explosion-Proof PTZ Camera via a modem
Purpose:
This Explosion-Proof PTZ Camera supports the PPPoE auto dial-up function. The Explosion-Proof
PTZ Camera gets a public IP address by ADSL dial-up after the Explosion-Proof PTZ Camera is
connected to a modem. You need to configure the PPPoE parameters of the Explosion-Proof PTZ
Camera. Refer to Section 6.1.1 Configuring PPPoE Settings for detailed configuration.

User Manual of Explosion-Proof PTZ Camera
9
The obtained IP address is dynamically assigned via PPPoE, so the IP address always changes after
rebooting the Explosion-Proof PTZ Camera. To solve the inconvenience of the dynamic IP, you
need to get a domain name from the DDNS provider (E.g. DynDns.com). Follow the steps below
for normal domain name resolution and private domain name resolution to solve the problem.
Normal Domain Name Resolution
Steps:
1. Apply a domain name from a domain name provider.
2. Configure the DDNS settings in the DDNS Settings interface of the Explosion-Proof PTZ
Camera. Refer to Section 6.1.1 Configuring DDNS Settings for detailed configuration.
3. Visit the Explosion-Proof PTZ Camera via the applied domain name.

User Manual of Network Explosion-Proof PTZ Camera
10
Chapter 3 Accessing to the
Explosion-Proof PTZ Camera
3.1 Accessing by Web Browsers
Steps:
1. Open the web browser.
2. In the address field, input the IP address of the Explosion-Proof PTZ Camera, e.g.,
192.168.1.64 and enter the login interface.
3. Activate the Explosion-Proof PTZ Camera for the first time using. Refer to the section 2.1.2
Activating the Explosion-Proof PTZ Camera.
4. Select English as the interface language on the top-right of login interface.
5. Input the user name and password and click .
The admin user should configure the device accounts and user/operator permissions properly.
Delete the unnecessary accounts and user/operator permissions.
The device IP address gets locked if the admin user performs 7 failed password attempts (5
attempts for the user/operator).
Figure 3-1 Login Interface
6. Install the plug-in before viewing the live video and operating the Explosion-Proof PTZ
Camera. Follow the installation prompts to install the plug-in.
You may have to close the web browser to install the plug-in. Reopen the web browser and
log in again after installing the plug-in.

User Manual of Explosion-Proof PTZ Camera
11
Figure 3-2 Download and Install Plug-in

User Manual of Network Explosion-Proof PTZ Camera
12
Chapter 4 Basic Operations
In this and the following chapters, operation of the Explosion-Proof PTZ Camera by the web
browser will be taken as an example.
4.1 Power-up Action
After the power is applied, the Explosion-Proof PTZ Camera will perform self-test action. It begins
with lens action and then pan/tilt movement.
After the self-test action, the system information of the Explosion-Proof PTZ Camera including the
model, address, communication, version, and other will be displayed on screen for 40 seconds.
4.2 Configuring Local Parameters
The local configuration refers to the parameters of the live view and other operations using the
web browser.
Steps:
1. Enter the Local Configuration interface:
Configuration > Local
Figure 4-1 Local Configuration Interface
2. Configure the following settings:
Live View Parameters: Set the protocol type, play performance, rules and image format.
Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.
TCP: Ensures complete delivery of streaming data and better video quality, yet the

User Manual of Explosion-Proof PTZ Camera
13
real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
MULTICAST: It’s recommended to select the protocol type to MULTICAST when using
the Multicast function.
HTTP: Allows the same quality as of TCP without setting specific ports for streaming
under some network environments.
Play Performance: Set the play performance to Shortest Delay, Balanced, or Fluent.
Rules: You can enable or disable the rules of dynamic analysis for motion here.
Image Format: The captured pictures can be saved as different format. JPEG and BMP are
available.
Record File Settings: Set the saving path of the video files.
Record File Size: Select the packed size of manually recorded and downloaded video files.
The size can be set to 256M, 512M or 1G.
Save record files to: Set the saving path for the manually recorded video files.
Save downloaded files to: Set the saving path for the downloaded video files in
interface.
Picture and Clip Settings: Set the saving paths of the captured pictures and clipped video
files.
Save snapshots in live view to: Set the saving path of the manually captured pictures in
interface.
Save snapshots when playback to: Set the saving path of the captured pictures in
interface.
Save clips to: Set the saving path of the clipped video files in interface.
You can click Browse to change the directory for saving video files, clips and pictures.
You can click Open to directly open the video files, clips and pictures.
3. Click to save the settings.
4.3 Live View Page
Purpose:
The live video page allows you to view live video, capture images, realize PTZ control, set/call
presets and configure video parameters.
Log in the Explosion-Proof PTZ Camera to enter the live view page, or you can click on
the menu bar of the main page to enter the live view page.

User Manual of Explosion-Proof PTZ Camera
14
The functions vary depeding on different Explosion-Proof PTZ Camera models. Refer to the actual
interface as standard.
Descriptions of the live view page:
Menu Bar
Live View
Parameters
Live View Window
Toolbar
Show or hide PTZ
control panel
PTZ Control
Preset/Patrol/Pattern
Figure 4-2 Live View Page
Menu Bar:
Click each tab to enter Live View, Playback, Picture, and Configuration page respectively.
Click to display the help file of the Explosion-Proof PTZ Camera.
Click to logout the system.
Live View Window:
Display the live video.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio on/off, regional exposure,
regional focus, etc.
PTZ Control:
Panning, tilting, focusing and zooming actions of the network. The lighter, wiper, one-touch focus
and lens initialization control.
Preset/patrol/pattern:
Set and call the preset/patrol/pattern for the Explosion-Proof PTZ Camera.
Live View Parameters:
Configure the image size, stream type, plug-in type, and two-way audio of the live video.
4.4 Starting Live View
In the live view window as shown in Figure 4-3, click on the toolbar to start the live view of
the network.