Honeywell HD5 Series User manual

Document 800-04763 – Rev B – 08/09
User Guide
HD5
Pendant or Ceiling Mount
Fixed Dome Camera

2
Revisions
Issue Date Revisions
A 07/09 New document to replace 800-03526 Rev
A; changed the DIP switch settings for
configuring a 540 TVL camera
B 08/09 New Revision created to include the
missing Table of Contents

Document 800-04763 Rev B 3
08/09
Warnings
WARNING! The Use of CSA Certified/UL Listed Class 2 power
adapters is required to ensure compliance with
electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of
this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.
Read Instructions All the safety and operating instructions should be read
before the equipment is operated.
Retain Instructions The safety and operating instructions should be
retained for future reference.
Cleaning Do not use liquid aerosol cleaners. Use a damp soft cloth.
Attachments Never add any attachments and/or equipment without the
approval of the manufacturer as such additions may result in the risk of fire,
electric shock, or injury.
Water and/or Moisture This is an indoor rated product. To prevent fire or
shock hazard, do not expose this camera to rain or moisture.
Do not use this equipment near water or in contact with water.

4
Accessories Wall or shelf mounting should follow the manufacturer’s
instructions, and should use a mounting kit approved by the manufacturer.
Power Sources This equipment should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power, please consult your equipment dealer or local power company.
Servicing Do not attempt to service this equipment yourself. Refer all
servicing to qualified service personnel.
Field Installation This installation should be made by a qualified
service person and should conform to all local codes.
Explanation of Graphical Symbols
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
CAUTION

Document 800-04763 Rev B 5
08/09
FCC Compliance Statement
Information to the User: This equipment has been tested and found
to comply with the limits for a Class A digital device. Pursuant to Part
15 of the FCC Rules, these limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Caution Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.

6
Manufacturer’s Declaration of
Conformance
The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC directive
2004/108/EC and the Low Voltage Directive (LVD) 2006/95/EC, conforming
to the requirements of standards EN 55022 for emissions, EN 50130-4 for
immunity, and EN60065 for Electrical Equipment safety.

Document 800-04763 Rev B 7
08/09
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Camera Model Configurations . . . . . . . . . . . . . . . . 10
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 13
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing the Lens . . . . . . . . . . . . . . . . . . . . . . . 17
Housing Installation . . . . . . . . . . . . . . . . . . . . . . 19
Installing without a Back Box . . . . . . . . . . . . 19
Installing a Pendant Dome . . . . . . . . . . . . . 20
Installing with a Back Box (ceiling or wall mount). . 22
Setting Up the Camera. . . . . . . . . . . . . . . . . . . . . . 24
Connecting a Spot Monitor . . . . . . . . . . . . . . . . . . 24
Adjusting the Field of View and Focus . . . . . . . . . . . . 25
Adjusting the Field of View (FOV) . . . . . . . . . . 25
Focusing the Lens . . . . . . . . . . . . . . . . . . 26
Configuring the Camera. . . . . . . . . . . . . . . . . . . . 27
Configuring a 540 TVL Camera . . . . . . . . . . . 28
Configuring a WDR Camera . . . . . . . . . . . . . 30
Configuring a DNR Camera . . . . . . . . . . . . . 41
Installing the Turret . . . . . . . . . . . . . . . . . . . . . . 50
Attaching the Safety Lanyard . . . . . . . . . . . . . . . . . 51
Installing the Lower Dome. . . . . . . . . . . . . . . . . . . 52
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 58

8

Document 800-04763 Rev B 9
08/09
Introduction
Description
The HD5 series of stationary dome cameras is ideal for discreet fixed
camera surveillance where high-quality video is a necessity. Each unit
combines a high-performance camera and a full-sized lens into a 5" dome.
Features
The HD5 series includes the following features:
• Easy dome installation into a standard 4" x 4" x 2-1/8" electrical box
• Black or white trim-ring finishes available
• Simple installation and maintenance
• Adjustable camera mount (included with camera/lens)
• NTSC and PAL versions; ETL, EMC, and EU (CE) certified
• Vari-focal lenses available:
Auto iris lenses: 2.7–13.5 mm or 5–50 mm
or
Manual iris lenses: 2.7–13.5 mm or 5–50 mm
• Optional UTP (CAT5) video transmission
• 4-pin Auto Iris connector standard

10
Camera Model Configurations
There are three camera models (HD5CH, HD5U, or HD5SD), two
connection format choices, (Coaxial or UTP), four lens choices, four lower
dome choices, and two video format choices (NTSC or PAL). The part
number of your camera indicates what choices have been made.

Document 800-04763 Rev B 11
08/09
Table 1 Camera Models
Camera Model
Number
Video Format Connection
Format
Model
HD5CH NTSC COAX 540 TVL
HD5CHTP NTSC UTP 540 TVL
HD5CHX PAL COAX 540 TVL
HD5CHTPX PAL UTP 540 TVL
HD5U NTSC COAX WDR
HD5UTP NTSC UTP WDR
HD5UX PAL COAX WDR
HD5UTPX PAL UTP WDR
HD5SD NTSC COAX DNR
HD5SDTP NTSC UTP DNR
HD5SDX PAL COAX DNR
HD5SDTPX PAL UTP DNR

12
Lower Dome Model Description
HD5CBL Clear dome, black trim ring
HD5CWH Clear dome, white trim ring
HD5TBL Smoked dome, black trim ring
HD5TWH Smoked dome, white trim ring
Lens Model Description
HLD27V13DNL 2.7 - 13.5 mm DC
HLM27V13DN 2.7 - 13.5 mm Manual
HLD5V50F13L 5 - 50 mm DC
HLM5V50F13 5 - 50 mm Manual

Document 800-04763 Rev B 13
08/09
Figure 2 Example of a High Level Part Number
Before You Begin
There are a few things you can do to prepare yourself and your camera for
the installation process:
• Ensure you have a monitor to connect to the camera for adjusting
the field of view and camera lens settings.
• Remove the turret from the gimbal. See Removing the Turret on
page 14.
• Know the type of wiring connection for your camera, either BNC
or UTP.
• Look for the DIP switches if you are installing a 540 TVL camera.
You will use the dip switches later when you are configuring the
camera.
Note Wide Dynamic Range (WDR) and Digital Noise Reduction
(DNR) cameras are programmable. Therefore, the joystick on
the gimbal is operational. See Configuring a WDR Camera on
page 30 and Configuring a DNR Camera on page 41.
Camera
Type
C = Hi Res
U = WDR
S = DNR
Video
Connection
Format
Blank = Coax
T = UTP
Lens
2 = 2.7 mm - 13.5 mm DC
5 = 5 mm - 50 mm DC
3 = 2.7 mm - 13.5 mm
Manual
6 = 5 mm - 50 mm Manual
Dome/Trim
A = Clear/Black
B = Clear/White
C = Smoked/Black
D = Smoked/White
Standard
Blank = NTSC
X = PAL
HD5CT2AX

14
Removing the Turret
You must remove the turret from the camera gimbal before you can install
and adjust (position, focus, iris) the lens or, with some models, before you
can access the DIP switches or joystick for configuring the camera.
Caution ·Always handle the bottom housing from its outside
surface.
·The bubble surface can be cleaned with a non-abrasive
glass cleaner.
Turret
Gimbal
Camera base

Document 800-04763 Rev B 15
08/09
Cable Options
The HD5 is shipped with two wiring configurations for the video
connection: BNC or UTP (twisted pair). To connect the power, attach the
green connector terminal to the two bare wires.
1. Connect the BNC or UTP video connection.
The yellow wire is the positive connection.
The gray wire is the negative connection.
2. Connect the camera power (12VDC or 24VAC).
Power
Video
BNC UTP
Green
connector
terminal
Camera base
yellow=positive
gray=negative

16
Installation
There are three installation options, and the installation process is slightly
different for each. Please see the following table for the steps for installing
your camera:
Ceiling or Wall
Mount (without
back box)
Ceiling or Wall
Mount (with back
box) (See note
on page 17)
Pendant Dome
Installing the
lens
see Installing the Lens on page 17
Installing the
mount
see Installing
without a Back Box
on page 19
see Installing with a
Back Box (ceiling or
wall mount) on page
22
see Installing a
Pendant Dome on
page 20
Making the
connections
see step 3 on
page 22
see Cable Options on page 15
Positioning
the camera
Adjusting the Field of View (FOV) on page 25
Adjusting the
lens (focus
and iris)
Focusing the Lens on page 26

Document 800-04763 Rev B 17
08/09
Note The back box is not supplied. Also, if you have a BNC
connection and are installing the HD5 with a back box, you
will need to purchase the Back Box Extender kit. Contact
Honeywell Customer Service to order (see the back cover for
contact information).
Note The camera configuration process is different for WDR and
DNR camera types.
Installing the Lens
The HD5 is shipped with one of four lenses (Manual or Auto Iris 2.7-13.5
mm; Manual or Auto Iris 5-50 mm). Installing an Auto Iris lens involves an
extra step, which is to connect the lens control cable. See step 3.
Configuring
the camera
(See note)
To configure a 540 TVL camera, see Configuring a 540 TVL Camera on
page 28.
To configure a WDR camera, see Configuring a WDR Camera on page
30.
To configure a DNR camera, see Configuring a DNR Camera on page 41.
Installing the
turret
see Setting Up the Camera on page 24
Installing the
lower dome
see Ceiling or Wall Mount on page 52 see Pendant Mount
on page 53
Ceiling or Wall
Mount (without
back box)
Ceiling or Wall
Mount (with back
box) (See note
on page 17)
Pendant Dome

18
Note To protect the lens, leave the lens cap on the lens until you
have installed it.
1. Remove the lens from its box.
2. Screw the lens into the lens mount.
3. If you have the Auto Iris lens, insert the lens control cable into the lens
control connector.
Lens mount
Auto Iris lens control
connector
Caution Ensure that the lens is screwed all the way into the
mount. If it is not secured, it could become loose when
you are adjusting the zoom and focus.

Document 800-04763 Rev B 19
08/09
Housing Installation
There are three options for mounting the HD5 camera: in-ceiling without a
back box, pendant (kit not supplied), and in-ceiling with a back (gang) box
(not supplied).
Installing without a Back Box
Note Your local state regulations might require that all wiring be
contained within a metal box. If you have a BNC connection,
then you might require a Back Box Extender Kit to gain
additional space to contain the coiled wires. Contact
Honeywell Customer Service to order the Back Box Extender
Kit (see the back cover for contact information). Please follow
the installation instructions included with that kit.
1. Peel off the backing paper of the round template (found in packing
box), then affix the mounting template to the mounting surface.
2. Pre-drill at least three holes around the circle, as indicated on the
template, using the recommended hole size for the screws being
used. Trace the outline of the circle for the HD5 housing.
3. Remove the mounting template and cut the round hole for the HD5
housing.

20
4. Install the 3 mounting screws
(supplied). You might want to
use drywall anchors (not
supplied).
5. Slide the spacer down onto
the lower dome.
6. Connect the wiring as shown
in Cable Options on page 15.
7. Mount the camera to the
ceiling by fitting the large
ends of the keyhole slots over
the large ends of the
mounting screws, then
rotating the camera mount
counter-clockwise to lock into
place.
8. Tighten the mounting screws
to secure the HD5.
Installing a Pendant Dome
A pendant kit is available for the HD5 as an optional mounting choice.
Contact Honeywell Customer Service to order (see the back cover for
contact information). These installation instructions assume the mount for
the fixed camera dome has already been installed in the pendant. The top
Mounting screws
Keyhole slots
Spacer
Lower dome
55
6
7
8