Honeywell Performance HBD3PR2 User manual

HBD3PR2 True Day/Night Indoor/Outdoor IR
Bullet IP Camera Regulatory Statements
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Quick Installation Guide
Document 800-21233V1— Rev A– 10/2015
Thank you for purchasing a HBD3PR2 camera.
Follow the
instructions in this guide to install and
log to
your camera. For instructions on
configuring the
camera, refer to the Performance
Series IP Cameras User Guide on the software
and
documentation CD that came with your
camera. If
you require additional assistance,
please call the
number shown below.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Cautions and Warnings
•
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Important Safeguards
WARNING
•
•
Read and keep these instructions.
Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
Do not touch the camera lens.
Do not drop the camera or subject it to physical shock.
Do not use a strong or abrasive detergent when cleaning the camera.
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the
operating temperature is outside the recommended range of -4°F to 140°F (–20°C to 60°C).
To ensure compliance with electrical safety standards this product is
intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,
on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE
802.3af PoE standard. •
•
•
•
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam. Note
Do not apply power to the camera before completing installation.
Note
Confirm the installation surface can support at least three times the weight of the camera plus
the bracket.
Document 800-21233V1– Rev A – 10/2015 1
CAUTION THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN

HBD3PR2 True Day/Night Indoor/Outdoor IR Bullet IP Camera
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
or damaged, contact your dealer immediately.
•
•
•
•
Camera
Documentation CD
Quick install guide
Allen key (L-wrench)
•
•
•
Self-tapping screws (×3)
Plastic wall anchors (×3)
Mounting template
2
b. Insert the microSD card into the microSD card slot as
shown in the picture at right.
c. Replace the control panel.
2. Connect the camera with the Ethernet cable and the power
cable.
Required tools:
•
•
A Phillips screwdriver
A drill with an appropriately-sized drill bit for pre-drilling holes for the screw anchors.
CAUTION
Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain your
warranty.
3
Aiming the Camera
1. Use the supplied Allen key to loosen the adjusting screws
on the bracket arm.
2. Set the camera to the desired position.
3. Tighten the adjustment screws.
1
Preparing the Mounting Surface
1. Inspect the site where you want to install the camera. The mounting surface must be
flat and capable of supporting at least three times the weight of the camera.
2. Remove the backing from the mounting template sticker and affix the sticker to the
mounting surface.
Note If you are using the side exit for the cable, note the orientation of the cable exit
notch. In outdoor installations the notch should point downwards to prevent water from
entering the camera housing.
Document 800-21233V1 – Rev A– 10/2015
© 2015 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
3. Drill three screw holes at the locations indicated on the mounting template sticker and
insert the three supplied plastic anchors in the holes.
4. If you want to store the cables inside the wall or ceiling, drill a hole at the cable exit position
on the mounting template and then pull the cables through the hole.
Mounting the Camera
1. If local storage is needed, insert a micro SD card into the micro SD card slot
according to the following steps:
a. Use a Phillips screwdriver (not supplied) and remove the control panel cover
on the outside of the camera.
4
Adjusting the Zoom and Focus Settings
The cameras connected to a PoE port of the Honeywell Embedded NVR can be configured
with the NVR directly.
To log on to the camera with a PC, perform the following steps:
1. Install the Honeywell Config Tool from the software and the documentation CD, find the
camera and open the web browser with the Honeywell Config Tool
2. Log on to the camera as the admin user. The default user name is admin (case-sensitive)
and the default password is 1234.
3. Go to Setup CameraConditionsZoom and Focus. The following panel appears:
•Click Zoom in + or Zoom out – to zoom in or out.
•Click Near – or Far + to focus near or far, or click Auto Focus to enable auto focus.
[phone]
www.honeywell.com/security
(North America only)
[phone]
www.honeywell.com/security/uk
(Europe only)
[phone]
www.asia.security.honeywell.com
(Asia Pacific only)
a. Connect one end of the Ethernet cable to the RJ-45 port on the camera.
b. If the other end of the Ethernet cable is NOT connected to a PoE (Power-over-
Ethernet) switch or NVR, connect the power connector of the camera to a 12 V
DC power source.
3. Attach the camera assembly to the mounting surface using the supplied screws.