Honeywell SC105 Operation manual

Honeywell
Mini-Seismic Vibration Detector SC105
Planning and Installation
User Guide
To get the best use of the product, please read the User Guide carefully before using the product.
Keep the User Guide at an easily accessible place and make it available to the next user.
© 2010 Honeywell International Inc. All rights reserved.
http://www.security.honeywell.com/
Document 800-04997 Rev. A

Honeywell
i
TO THE INSTALLER
Before planning and installing Seismic Vibration Detector SC100, the circumstances below should
be avoided:
Electrical Devices
Water piping
Do not apply the detectors close to electrical
devices (such as electric motors, transformers,
fans, air conditioners and so on), which may
create mechanical vibrations in the protected
structure.
Avoid mechanical contact between such
devices and the protected surface, or using
appropriate insulating materials to reduce the
vibrations.
Do not apply the detectors close to water
piping.
The flow of water through piping, when in
mechanical contact with the protected
structure, emits a strong signal in the
structure itself, which may cause nuisance
alarms.
Bells
Human activity
Do not apply the detectors close to the bells;
Or apply a piece of tape on the bell to suppress
the overtones generated in the frequency range
of the detectors.
Apply carpet or vibration damping material
on vaults and under safes placed on
concrete or marble floors.
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the
user are vital to continuous satisfactory operation of any product.
The installer should assume the responsibility of developing and offering a regular maintenance
program to the user, as well as acquainting the user with the proper operation and limitations of
the product and its component parts. Recommendations must be included for a specific program
of frequent testing to insure the product’s operation at all times.

Honeywell
ii
LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller")
165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be in conformance with its
own plans and specifications and to be free from defects in materials and workmanship under
normal use and service for 24 months from the date stamp control on the product(s) or, for
product(s) not having a manufacturer’s date stamp, for 12 months from date of original purchase
unless the installation instructions or catalog sets forth a shorter period, in which case the shorter
period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of
charge for materials or labor, any product(s) which is proved not in compliance with Seller's
specifications or proves defective in materials or workmanship under normal use and service.
Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered
or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty
service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way,
Syosset, New York 11791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR
FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO
ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS
OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF
LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S
OWN NEGLIGENCE OR FAULT.
Seller does not represent that the product(s) it sells may not be compromised or circumvented;
that the product(s) will prevent any personal injury or property loss by burglary, robbery, fire or
otherwise; or that the product(s) will in all cases provide adequate warning or protection.
Customer understands that a properly installed and maintained alarm system may only reduce
the risk of a burglary, robbery, fire,or other events occurring without providing an alarm, but it is
not insurance or a guarantee that such will not occur or that there will be no personal injury or
property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT
THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,
WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS
LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE
PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST
SELLER.
This warranty replaces any previous warranties and is the only warranty made by Seller on this
product(s). No increase or alteration, written or verbal, of the obligations of this Limited Warranty
is authorized.

Honeywell
i
Contents
1About This Document ......................................................................................................................................1
Overview of Contents ..............................................................................................................................1
Special Font and Symbols.......................................................................................................................1
How to Use This Document.....................................................................................................................1
2Introduction ......................................................................................................................................................2
Overview of the Detector .........................................................................................................................2
Applications .............................................................................................................................................2
Features ..................................................................................................................................................3
3Function Description ........................................................................................................................................4
Function Criteria ......................................................................................................................................4
Detection Parameters........................................................................................................................4
Alarm Criteria.....................................................................................................................................4
Function Modules ....................................................................................................................................4
Sensor Element .................................................................................................................................4
Signal Conditional Block....................................................................................................................4
Switch Block ......................................................................................................................................5
Micro Controller Block .......................................................................................................................5
Output Alarm Block............................................................................................................................5
Power Supply Block...........................................................................................................................5
Sabotage Protection ..........................................................................................................................5
4Basic Accessories............................................................................................................................................6
5Planning Protections........................................................................................................................................7
Mini-ATMs ...............................................................................................................................................7
Vending Machines and Ticket Machines .................................................................................................7
6Installation........................................................................................................................................................9
Mounting the Detector .............................................................................................................................9
Opening the Detector ........................................................................................................................9
Mounting on Steel..............................................................................................................................9
Mounting on Stainless Steel or Hardened Steel ..............................................................................10
Mounting the Accessories .....................................................................................................................11
The Movable Mounting Kit SC111 ...................................................................................................11
The Keyhole Protection Kit SC112 ..................................................................................................11
The Spacer for Keyhole Protection Kit SC118.................................................................................11
The Armored Cable Kit SC114 ........................................................................................................12
The Test Transmitter SC113 ...........................................................................................................12
The External Test Transmitter SC115 .............................................................................................12
7Settings..........................................................................................................................................................13
DIP Switch Settings ...............................................................................................................................13
EOL Jumper Settings ............................................................................................................................14
J19/J20 Settings....................................................................................................................................14
J1 Setting ..............................................................................................................................................14
8Connecting the Detector ................................................................................................................................15
9Test................................................................................................................................................................16
Control and Function Test .....................................................................................................................16
Remote Test (Alternative)......................................................................................................................16
10 Technical Specifications ................................................................................................................................18

Honeywell
ii
Figures
Figure 2-1 Detector Description ...................................................................................................................................................... 2
Figure 5-1 Planning ATM Protection............................................................................................................................................... 7
Figure 5-2 Planning Vending Machine/Ticket Machine Protection ................................................................................................. 8
Figure 6-1 Opening the Detector .................................................................................................................................................... 9
Figure 6-2 Drill Plan ........................................................................................................................................................................ 9
Figure 6-3 Mounting Plate SC110 - UPSIDE DOWN ................................................................................................................... 10
Figure 6-4 Movable Mounting Kit SC111 Components ................................................................................................................ 11
Figure 6-5 Keyhole Protection Kit SC112 Components................................................................................................................ 11
Figure 6-6 Spacer for Keyhole Protection Kit SC118 Components .............................................................................................. 11
Figure 6-7 Armored Cable Kit SC114 ........................................................................................................................................... 12
Figure 6-8 Test Transmitter SC113 .............................................................................................................................................. 12
Figure 6-9 External Test Transmitter SC115 Components........................................................................................................... 12
Figure 7-1 Function modules on Detector Base ........................................................................................................................... 13
Figure 8-1 Wirings on the terminal block ...................................................................................................................................... 15
Figure 8-2 Alarm and tamper configured to one loop ................................................................................................................... 15
Figure 8-3 Alarm and tamper configured to two loops.................................................................................................................. 15

Honeywell
iii
Tables
Table 2-1 Application Settings ........................................................................................................................................................ 2
Table 9-1 Remote Test ................................................................................................................................................................. 17

Honeywell
- 1 -
1 About This Document
Thank you for purchasing Honeywell Mini-Seismic Vibration Detector SC105!
This guide is designed to be a reference for the planning and installation of Mini-Seismic Vibration
Detector SC105.
Overview of Contents
This document contains the following chapters:
Chapter 1, About This Document, gives a brief introduction of “Mini-Seismic Vibration
Detector SC105 Planning and Installation User Guide”.
Chapter 2, Introduction, general information about Mini-Seismic Vibration Detector SC105,
applications and features.
Chapter 3, Function Description, introduces the function criteria and function modules of
Mini-Seismic Vibration Detector SC105.
Chapter 4, Basic Accessories , lists all basic accessories will be used with Mini-Seismic
Vibration Detector SC105.
Chapter 5, Planning Protections, gives an instruction on planning Mini-Seismic Vibration
Detector SC105 on different applications.
Chapter 6, Installation, introduces how to install Mini-Seismic Vibration Detector SC105 and
related accessories.
Chapter 7, Settings, shows how to configure sensitivities and other settings on Mini-Seismic
Vibration Detector SC105 base.
Chapter 8, Connecting the Detector, introduces how to wire and connect Mini-Seismic
Vibration Detector SC105 to the protected zone.
Chapter 9, Test, introduces the tests of the Mini-Seismic Vibration Detector SC105.
Chapter 10, Technical Specifications, introduces technical specification of Mini-Seismic
Vibration Detector SC105.
Special Font and Symbols
Italic references
Note the important notice should pay attention to
Caution important operating alerted
How to Use This Document
Pictures in the manual are for reference only, so please see the actual items.
The products will be updated and the information shall not be distributed.
Please read the book before operation and keep it properly for future use.
The manual has been reviewed and the accuracy is guaranteed. If there is any uncertainty
or controversy, please refer to the final explanation of Honeywell. Honeywell does not take
any responsibility for any consequences caused by misunderstanding of the manual or
improper operations.

Introduction
2 Introduction
Overview of the Detector
Mini-Seismic Vibration Detector SC105 is a seismic or structural vibration detector designed to
detect selected vibrations from burglary or intrusion attempts on high value storage units, such as
Mini-ATMs, Vending Machines and Ticket Machines.
The detector consists of a sensor element to convert mechanical vibrations to electrical signals, a
signal conditional block, micro controller block, output alarm block, tamper protection, and a
switching block for selecting detector settings, all in a miniature metal housing.
Figure 2-1 Detector Description
Detector Cover Detector Base
Applications
Mini-Seismic Vibration Detector SC105 is designed to detect any known attack tool on:
Mini-ATMs (Lobby ATMs)
Vending machines
Ticket machines
According to the vibration characteristics of the application constructions, sensitivity required in
each sensor, and the natural vibrations and ambient noise level in the premises, the detection
ranges of Detector SC105 should follow the parameters in the table below.
Table 2-1 Application Settings
Sensitivity
Settings Material Detection Radius Applications Noise Level
Steel 3.0 m
Ghigh
Concrete 2.0 m
Mini-ATMs (grade 3,4) Insignificant noise
level
Steel 1.5 m
Gnormal
Concrete 1.0 m
Mini-ATMs (grade 1,2) Moderate noise level
Glow Steel 1.0 m
Vending machines, Ticket
machines
Considerable noise
level
Gnoisy Sheet
Steel < 3.0 m Vending machines, Ticket
machines Heavy noise level
Note
Sensitivity settings (Ghigh, Gnormal, Glow, Gnoisy) are defined in “DIP Switch Settings” on page
13.
The parameters in the table above are for reference only, and they may vary according to
the quality of the material.
The detection range will be reduced if cracks and joints exist in the material.
- 2 -

Honeywell
- 3 -
Features
Mini-Seismic Vibration Detector SC105 has the following features:
24-hour detection of known attack tools on Mini-ATMs, Vending Machines and so on.
Flat frequency non resonant response sensor for genuine frequency analysis.
Built-in diagnostic tool used to set detector sensitivity in relation to existing noise level.
DIP switch sensitivity settings adapt to various applications.
Integrated EOL resistors compatible with various control panels.
High detection capability due to new sophisticated signal handling and computer algorithms
incorporated.
Low current consumption.
Solid state form A breaking alarm relay.
Multipurpose accessories provided with multiple applications.
Standard drill sheet protection.
Rate of Rise and temperature alarm.
Miniature metal housing – easy to fit in restricted spaces.
Approved by IMQ type 3 (pending), UL (pending), ULC (pending), CE, and CCC (pending).

Function Description
3 Function Description
Function Criteria
Detection Parameters
The detection function of Mini-Seismic Vibration Detector SC105 is based on the structural
vibrations generated on the protected surfaces upon an attempt to break through the physical
barriers.
Vibrations detected comprise four important parameters:
signal strength (amplitude)
signal frequency (spectra)
signal duration
structure of duration
These parameters differ between real attacks and "normal" background vibrations and will be
detected and analyzed by the detector before an alarm is triggered. The characteristics below
represent signals that can be detected by Detector SC105:
Signals with very high amplitude and short duration, which can be generated by explosives.
Signals with medium to high amplitude and medium to long or intermittent duration, which
can be generated by mechanical demolition tools.
Signals with wide frequency spectra, low amplitude and long duration, which can be
generated by thermal attacks.
Alarm Criteria
In Detector SC105, the signals detected will be analysed by several parallel software detection
modes with specific algorithms for detection of known attack methods and tools, which can be
described as below:
The low level detection mode is designed to recognize low to medium amplitude signals
with long duration, like those caused by a thermic lance, oxy-arc or acetylene torch.
The medium level detection mode is designed to detect medium to high amplitude
signals as caused by mechanical demolition, such as electric power tools.
The high level detection mode is designed to detect very high amplitude and short
duration signals as caused by explosives.
The signal from the sensor is fed to the signal conditioning block and further to the micro
controller for evaluation. An alarm signal will be sent to the output alarm block when a criteria with
signal strength, frequency spectra and signal duration is achieved.
Function Modules
Sensor Element
Mini-Seismic Vibration Detector SC105 includes a sensor element that converts mechanical
vibrations into electrical signals providing a non resonant flat frequency response for genuine
signal analysis, which is used for detection of structural vibrations caused by attacks against the
protected surface. These signals will be analyzed in different software detection modes.
Signal Conditional Block
The electrical signal that sensor converted is fed to the signal conditional block that adapts the
signal for further analysis. It also contains circuits for supply voltage and temperature supervision
(see Alarm Criteria on page 4). This block also generates test signals for the Test Transmitter
SC113.
- 4 -

Honeywell
- 5 -
Switch Block
This block contains the DIP switches for sensitivity settings, application settings and the noise
LED settings, further communicating with the micro controller and signal conditional blocks.
Micro Controller Block
This block is the heart of Detector SC105. It handles functions for signal analysis and recognition,
circuit supervision of power supply and temperature, noise recognition and indication, test and
sensitivity reduction etc.
It also contains a watchdog function which is used to detect system lockups and create an alarm
signal to the output alarm block. This block contains nano watt technology and the software code
stored in a flash program memory with code protection.
Output Alarm Block
The circuits in the output alarm block will be activated by the micro controller block when intrusion
attack signals are recognized. The alarm output provides two forms of alarm signals:
One potential free solid state SPST breaking relay.
One open collector transistor output, going into conductive mode upon alarm condition.
The transistor is protected against overload with a series resistor of 1.38k ohm.
Note No protection against sabotage attempts with external magnetic fields is needed due to solid
state alarm relay.
Power Supply Block
The input circuits are very well protected against electrical interference and high energy electrical
surges by filtering, transient absorber and spark gaps. The small mechanical dimensions, circuit
board layout and design, results in very good resistance against RFI from various transceivers,
cellphones and so on. Detector SC105 has a vide supply voltage range from 8 to 16 VDC due to
the low internal system voltage of 5 Volt.
Sabotage Protection
Mini-Seismic Vibration Detector SC105 has a full range of tamper protection facilities, thus an
alarm will be given when an attempt is made to:
Pry off the detector from the protected surface
Open the detector
Disable the detector by heat
Lower the supply voltage below 6.5V
The detector is equipped as standard with a stainless steel drill shield that makes it difficult to drill
into the detector and at the same time generates strong vibrations.

Basic Accessories
4 Basic Accessories
Mounting Plate SC110
Movable Mounting Kit SC111
Keyhole Protection Kit SC112
Test Transmitter SC113
Spacer for Keyhole Protection Kit SC118
External Test Transmitter SC115
Armored Cable Kit (8 wires) SC114
- 6 -

Honeywell
- 7 -
5 Planning Protections
Before mounting the detector, it is recommended to plan the mounting locations to achieve an
extremely high security level.
In general, the detectors should be mounted at the center of the protective surface (see Table 2-1
Application Settings on page 2.) or on the positions where most of the attacks are aimed at.
Caution Please read TO THE INSTALLER first before planning protections.
Mini-ATMs
Mini-ATMs are objects exposed to human made noise as well as extensive internal noise,
therefore detector sensitivity (DIP switch 1 and 2 and delay function DIP switch 3) settings should
be carefully tested before taking the installation in use.
For Mini-ATMs we recommend mounting:
At least one detector on or inside the safe cabinet close to the dispenser opening.
One detector on the door close to or between the hinges or inside the door leaf.
Figure 5-1 Planning ATM Protection
Close to the dispenser opening
On or inside the door
The Movable Mounting Kit SC111 or the Keyhole Protection Kit SC112 and the Armored Cable
Kit SC114 can be used when mounting detectors on the Mini-ATMs.
Vending Machines and Ticket Machines
Same as Mini-ATMs, Vending machines and ticket machines are objects exposed to human
made noise as well as extensive internal noise, therefore it is recommended that the application
setting for them should be Gnoisy.
For both Vending machines and ticket machines we recommend mounting:
At least one detector inside the machine close to the coin/bill compartment.
Another detector located in the machine close to where an attack is expected.

Planning Protections
Figure 5-2 Planning Vending Machine/Ticket Machine Protection
Close to expected
attack spot Close to coin/bill compartment
- 8 -

Honeywell
- 9 -
6 Installation
Mounting the Detector
Mini-Seismic Vibration Detector SC105 can be mounted on solid surfaces, of which the most
common surfaces are Steel, Stainless Steel and Hardened Steel.
Caution
Please read TO THE INSTALLER first before mounting the detector.
Before the installation is finished, make sure the sensitivity setting is correct and the
noise level is considered.
Detector should not be mounted on cinder block or other unproved masonry surface.
Opening the Detector
Before mounting the detector, loose the top screw to separate the detector cover from the
detector base.
Figure 6-1 Opening the Detector
Note:The top screw is only
used for fixing the cover, so
do not tighten it too much
when mounting the detector.
Mounting on Steel
When mounting the detector on a flat and smooth steel surface, both Drill Plan (see Figure 6-2
Drill Plan) and Detector Base (see Figure 2-1 Detector Description) can be used to mark the
mounting holes.
Figure 6-2 Drill Plan
Note Please remove the drill :
plan after mounting holes
have been drilled
C
A
A, B - Detector SC100 mounting hole
C - Test Transmitter SC113 mounting hole
Note:The drill plan shall be
removed after all of the
mounting holes have been
drilled.
B
Refer to the steps below to mount the Detector SC105 on steel.
1. Attach the Detector Base or Dill Plan on the mounting area, and then mark the outline and
center punch the detector mounting holes A, B and test transmitter mounting hole C.
2. Remove the Drill Plan or Detector Base, and then thoroughly remove the paint in the
outline marked on the mounting area.
Note: The remnant Drill Plan or paint will weaken the sensitivity badly.
A
B
Notes:
Detector base cannot be used to
mark test transmitter mounting
hole C.
Skip marking hole C if no Test
Transmitter SC113 is used.
C
A
B

Installation
3. Drill the detector mounting holes A, B (Ø
3.3mm and minimum 8 mm deep), and
then thread the two holes with a M4 Tap
(6mm at least).
4. Drill the Test Transmitter SC113
mounting hole C (Ø 3.3mm and
minimum 8 mm deep), and then thread
the hole with a M4 Tap (6mm at least).
Notes:
Cool the tools with oil while drilling and
threading.
Skip step 4 if no test transmitter is used.
5. Remove all of the burrs.
6. Attach the Test Transmitter SC113 on the
mounting area (at C) and then use the M4×
8mm screw to fix it.
Note: Skip this step if no Test Transmitter SC113 is
used.
C
7. Attach the detector base on the steel
surface and then use the two M4×8mm
screws provided to fix it.
8. Wire and configure the detector (see the
related chapter in this user guide), and after
a successful test use the top screw to fix the
detector cover properly.
Mounting on Stainless Steel or Hardened Steel
When mounting on stainless steel or hardened steel, the Mounting Plate SC110 (UPSIDE DOWN)
must be used and should be welded on the mounting surface first.
Figure 6-3 Mounting Plate SC110 - UPSIDE DOWN
FG
C
D
E
A
B
A, B– Detector SC105 mounting holes
C, D, – Test Transmitter SC113 locating hole
E– Mounting Plate SC110 mounting hole
F, G– Welding Slots
Refer to the steps below to mount the Detector SC105 on stainless steel or hardened steel.
1. Remove paint from the mounting area
(especially welding area).
2. Attach the Mounting Plate SC110 on the
mounting area, and then mark the
outline.
3. Fix the Mounting Plate SC110 into the
outline marked and ensure it cannot move,
and then along the INSIDE of the welding
slots weld the Mounting Plate SC110 on the
mounting surface.
Note: The welding must be done along the INSIDE of
the welding slots, otherwise the Mounting Plate
SC110 may be deformed.
4. Tap off slag and remove weld spatter and make sure the whole mounting surface is still flat.
5. Attach Test Transmitter SC113 on the mounting plate (at C) and then use the M4×8mm
screw to fix it.
Note: Skip this step if no Test Transmitter SC113 is used.
C
- 10 -

Honeywell
- 11 -
6. Attach the detector base on the
Mounting Plate SC110 and then use the
two M4×8mm screws provided to fix it.
7. Wire and configure the detector (see the
related chapter in this user guide), and after
a successful test use the top screw to fix the
detector cover properly.
Mounting the Accessories
A full range of mounting accessories for different applications facilitates a wide range of mounting
requirements.
The Movable Mounting Kit SC111
The Movable Mounting Kit SC111 consists of one mounting plate on which Detector SC105 is
mounted, one Day position plate on which Detector SC105 is positioned during non armed time,
and one Night position plate mounted on the protected surface, on which Detector SC105 is
positioned during armed time.
The figure below shows the components of the Movable Mounting Kit SC111. For more
information, please refer to “Movable Mounting Kit SC111 User Guide”.
Figure 6-4 Movable Mounting Kit SC111 Components
Mounting Plate
Day Position Plate
Night Position Plate
The Keyhole Protection Kit SC112
The Keyhole Protection Kit SC112 is used with Detector SC105 to prevent unlocking during
armed installation or loading explosives into the keyhole, as it at the same time is a mounting
plate for the Detector SC105 to detect intrusion attempts on doors.
The figure below shows the components of the Keyhole Protection Kit SC112. For more
information, please refer to “Keyhole Protection Kit SC112 User Guide”.
Figure 6-5 Keyhole Protection Kit SC112 Components
Cover Plate Base Plate
The Spacer for Keyhole Protection Kit SC118
The Spacer SC118 is used for Keyhole Protection Kit SC112 only if the steel slide on SC112
touches the keyhole collar on the protected surface. For more information, please refer to
“Keyhole Protection Kit SC112 User Guide”.
Figure 6-6 Spacer for Keyhole Protection Kit SC118 Components

Installation
The Armored Cable Kit SC114
The Armored Cable Kit SC114 is designed to be used as a protection of the detector cable from
the detector on the door of a safe or mini-ATMs.
The Armored Cable Kit SC114 includes the following items:
8 core cable, white
Flexible stainless steel conduit
Cable straps
Figure 6-7 Armored Cable Kit SC114
The Test Transmitter SC113
The Test Transmitter SC113 is used for checking the proper mounting, wiring and function of the
detector, and it should be mounted inside of the detector, about how to mount the Test
Transmitter SC113, please refer to Mounting the Detector on page 9.
Figure 6-8 Test Transmitter SC113
The External Test Transmitter SC115
The SC115 External Test Transmitter is a range test transmitter developed to generate a
simulated attack signal in protected object with multiple SC105 seismic detectors installed in
concrete vaults and all other solid structure value storage units, checking whether the mounting
and the function of the seismic detector is good.
The figure below shows the components of the External Test Transmitter SC115. For more
information, please refer to “External Test Transmitter SC115 Installation Guide”.
Figure 6-9 External Test Transmitter SC115 Components
Front Cover Transmitter Base
- 12 -