Honeywell Miller RACDTA-5K6/6FT Operator's manual

2
1.0 Exigences Générales, Avertissements et Limitations.........................15-16
2.0 Compatibilité du Système...................................................................16
2.1 Groupes de Produits Miller Fall Protection
3.0 Installation des Connecteurs D’ancrage.............................................17-25
3.1 Ancrage à anneau en D (410)
3.2 Ancrage à boulon en D (415, 416/417, 416SS/417SS, 418/419, 418SS/419SS)
3.3 Ancrage à boulon en D pour béton (417C)
4.0 Inspection et Entretien....................................................................... 26
Étiquettes de Produit.......................................................................... 39
Registre D’inspection et D’entretien................................................... 40
Table des Matières
Table of Contents
1.0 General Requirements, Warnings and Limitations.............................3-4
2.0 Purpose................................................................................................4
3.0 Warnings and Limitations...................................................................4-5
3.1 Compatibility Limitations
4.0 Drop Through Anchor............................................................................6
5.0 Zinc Plated Swivel Anchor....................................................................7
6.0 Stainless Steel Swivel Anchors...........................................................10
7.0 Zinc Plated Swivel Anchors.................................................................14
8.0 Hybrid Concrete Anchor......................................................................19
Product Labels................................................................................... 48
Inspection and Maintenance Log....................................................... 51
1.0 Requisitos Generales, Advertencias y Limitaciones.......................... 27-28
2.0 Compatibilidad del Sistema............................................................... 28
2.1 Grupos de Productos Anticaídas Miller
3.0 Instalación de los Conectores de Anclaje.......................................... 29-37
3.1 Ancla de argolla “D” montada (410)
3.2 Ancla “D” de perno (415, 416/417, 416SS/417SS, 418/419, 418SS/419SS)
3.3 Ancla “D” de perno (417C)
4.0 Inspección y Mantenimiento.............................................................. 38
Etiquetas del Producto....................................................................... 39
Registro de Inspección y Mantenimiento........................................... 40
Índice

User Instructions - English
3
Questions? CALL
1.800.873.5242
It is crucial that the authorized person/user of this equipment read and understand these instruc-
tions. In addition, federal law requires employers to ensure that all users are trained in the
proper installation, use, inspection, and maintenance of fall protection equipment. Fall protection
training should be an integral part of a comprehensive safety program.
Proper use of fall arrest systems can save lives and reduce the potential of serious injuries from
a fall. The user must be aware that forces experienced during the arrest of a fall or prolonged
suspension may cause bodily injury. Consult a physician if there is any question about the
user’s ability to use this product. Pregnant women and minor children must not use this product.
Thank you for your purchase of Miller fall protection equipment manufactured by Honeywell
Safety Products. Miller brand products are produced to meet the highest standards of quality at
our ISO 9001 certi ed facility. Miller equipment will provide you with years of use when cared for
properly.
Thank You
All persons using this equipment must read, understand and follow
all instructions. Failure to do so may result in serious injury or death.
Do not use this equipment unless you are properly trained.
WARNING
All warnings and instructions shall be
provided to authorized persons/users.
All authorized persons/users must reference
the regulations governing occupational
safety, as well as applicable ANSI or
CSA standards. Please refer to product
labeling for information on speci c OSHA
regulations, and ANSI and CSA standards
met by product.
Proper precautions should always be taken
to remove any obstructions, debris, material,
or other recognized hazards from the work
area that could cause injuries or interfere with
the operation of the system.
All equipment must be inspected before
each use according to the manufacturer’s
instructions.
All equipment should be inspected by a
quali ed person on a regular basis.
To minimize the potential for accidental
disengagement, a competent person must
ensure system compatibility.
Equipment must not be altered in any
way. Repairs must be performed only by
the manufacturer, or persons or entities
authorized in writing by the manufacturer.
Any product exhibiting deformities, unusual
wear, or deterioration must be immediately
discarded.
Any equipment subject to a fall must be
removed from service.
The authorized person/user shall have
a rescue plan and the means at hand to
implement it when using this equipment.
Never use fall protection equipment for
purposes other than those for which it was
designed. Fall protection equipment should
never be used for towing or hoisting.
Equipment must not be exposed to
environmental hazards and chemicals which
may produce a harmful effect.
Use in a corrosive or caustic environment
dictates a more frequent inspection and
servicing program to ensure the integrity of
the product is maintained.
1.0 General Requirements,
Warnings and Limitations

User Instructions - English
4
2.0 Purpose
The Miller swivel anchorage connectors ar designed to function as an interface between the
anchorage and a fall protection, work positioning, rope access, or rescue system for the purpose
of coupling the system to the anchorage. References to "anchorage connector' in this manual
include and apply to the swivel anchorage connectors, used with either 5,000 lb. or 10,000 lb
anchorage connectors.
Do not allow equipment to come in contact
with anything that will damage it including,
but not limited to, sharp, abrasive, rough
or high-temperature surfaces, welding,
heat sources, electrical hazards, or moving
machinery.
Do not expose the equipment to any
hazard which it is not designed to
withstand. Consult the manufacturer in
cases of doubt.
Always check for obstructions below the
work area to make sure potential fall path
is clear.
Allow adequate fall clearance below the
work surface.
Never remove product labels, which include
important warnings and information for the
authorized person/user.
Fall arrest systems used with the
anchorage connector must be rigged in
accordance to regulatory requirements.
3.0 Warnings and Limitations
Compliant fall protection and emergency rescue systems help prevent serious injury during fall
arrest. Users and purchasers of this equipment must read and understand the User Instructions
provided for correct use and care of this product. All users of this equipment must understand
the instructions, operation, limitations and consequences of improper use of this equipment and
be properly trained prior to use per OSHA 29 CFR 1910.66 and 1926.503 or applicable local
standards. Misuse or failure to follow warnings and instructions may result in serious
personal injury or death.
1. The user shall be equipped with a means of limiting the maximum dynamic forces exerted
on the user during the arrest of a fall to a maximum of 1800 lbf/8kN.
2. Use of this product must be approved by an Engineer or other qualied person to be
compatible with any and all structural & operational characteristics of the selected installation
location and system to be connected to this anchorage connector.
3. The anchorage connector must be inspected prior to each use for wear, damage, and other
deterioration. If defective components are found the anchorage connector must be immediately
removed from service in accordance with the requirements of OSHA 29 CFR 1910.66 and
1926.502.
4. The anchorage connector should be positioned in such a way that minimizes the potential
for falls and the potential fall distance during use. The complete fall protection system must be
planned (including all components, calculating fall clearance, and swing fall) before using.
5. The anchorage connector is designed for single user, with a capacity up to 310 lbs (140
kg) including clothing, tools, etc.
6. The anchorage connector is designed to be used in temperatures ranging from -40ºF to
+130ºF (-40°C to +54°C.

User Instructions - English
5
7. This anchorage connector should not be used as part of a horizontal lifeline system that has
not been designed and or approved to be used with 5,000-lbf anchorage connectors.
Always work directly under the anchor point to avoid a swing-fall injury.
Ensure that the anchorage connector is at a height that will not allow a lower level to be
struck should a fall occur. When selecting an anchorage point, always remember that
shock absorbers will elongate when subjected to fall arrest forces. Refer to the labels and
instructions provided with the connecting device to obtain the maximum elongation distance.
Anchorage requirements based on ANSI are as follows:
• For fall arrest systems, anchorages must withstand a static load of 5,000 lbs. (22.2kN) for
non-certied anchorages or two times the maximum arresting force for certied anchorages.
• For positioning systems, anchorages must withstand a static load of 3,000 lbs. (13.3kN) for
non-certied anchorages or two times the foreseeable force for certied anchorages.
• For travel restraint, anchorages must withstand a static load of 1,000 lbs. (4.5kN) for non-
certied anchorages or two times the foreseeable force for certied anchorages.
• For rescue systems, anchorages must withstand a static load of 3,000 lbs. (13.3kN) for non-
certied anchorages or ve-times the applied load for certied anchorages.
• When more than one personal fall arrest system is attached to an anchorage, the above
anchorage strengths must be multiplied by the number of personal fall arrest systems attached
to the anchorage.
3.1 Compatibility Limitations
COMPATIBILITY LIMITATIONS
All anchorage connectors must only be coupled to compatible connectors. OSHA 29 CFR
1926.502 prohibits snaphooks from being engaged to certain objects unless two requirements
are met: it must be a locking type snaphook, and it must be “designed for” making such a
connection. “Designed for” means that the manufacturer of the snaphook specically designed
the snaphook to be used to connect to the equipment listed. The following connections must be
avoided, because they can result in rollout* when a nonlocking snaphook is used:
• Direct connection of a snaphook to horizontal lifeline.
• Two (or more) snaphooks connected to one D-ring.
• Two snaphooks connected to each other.
• A snaphook connected back on its integral lanyard.
• A snaphook connected to a webbing loop or webbing lanyard.
• Improper dimensions of the D-ring, rebar, or other connection point in relation to
the snaphook dimensions that would allow the snaphook keeper to be depressed by
a turning motion of the snaphook.
*Rollout: A process by which a snaphook or carabiner unintentionally disengages from
another connector or object to which it is coupled. (ANSI Z359.1-2007)
The anchorage connector must be compatible with the snap hook or carabiner of the
connecting device and must not be capable of causing a load to be applied to the gate/
keeper.

User Instructions - English
6
4.0 Drop Through Anchor
5,000 lbf./22kN
Model Numbers RACDTA-5K/6FT (Drop though anchor with 4 in. (10 cm) round plate and
swivel), RACDTA-5K6/6FT (Drop through anchor with 6 in. (15 cm) square plate and swivel),
and RACDTA-5K12/6FT (Drop through anchor with 12 in. (30cm) square plate and swivel).
Warnings and Limitations
• Use only with Honeywell-approved personal fall arrest or restraint systems. The anchorage
must have the strength capable of supporting a static load, applied in the directions
permitted by the system, of at least 5,000-lbf (22kN) in the absence of certication.
Installation:
1. The drop through anchor-5k drop through anchor can only be used on a horizontal
surface that is above the users location.
2. Locate or create a through hole in concrete, steel or metal grating capable of
withstanding a 5,000-lbf. Static load or meeting OSHA 1926.502 requirements for a
safety factor of two. (Reference gure 1-A below for dimentional requirements.)
3. Place cable through the hole from top side. The label on plate should be facing up.
Plate must rest at and ush on the mounting surface.
Material: (A)” Minimum distance from edge/corner (B)” thickness
HOLE REQUIRMENT CHART
Concrete
Steel
12” in. (30.5 cm)
4” in. (10 cm)
4” in. (10 cm)
1/4” in. (.635 cm)
Tensile Strength (UTS): 5,000-lbf (22kN)
Working Load (WLL): 1,000 lbs (454kg)
Maximum Capacity: One worker, 310 lbs (140 kg)
Weight: Varies by cable length
Regulatory Compliance
ANSI Z359.1-2007, ANSI Z359.7-2011, OSHA 1910.66 , 1926.502
(A)
min fromany edge
(B)
min
1-3/4” to 2”Ø
Hole size
(4.1cm to 4.4cm)
Fig. 1-A

User Instructions - English
7
5.0 Zinc-Plated Swivel Anchor
5,000 lbf./22kN
Model Numbers RACSWY050N (swivel only), RACSWY050S (swivel anchor with steel mount-
ing hardware), and RACSWY050C (swivel anchor with concrete mounting hardware), RAC-
SWY2SBA (Steel mounting hardware only) and RACSWY2CSA (Concrete mounting hardware
only).
Warnings and Limitations
• Use only with Honeywell-approved personal fall arrest or restraint systems. The
anchorage must have the strength capable of supporting a static load, applied in
the directions permitted by the system, of at least 5,000-lbf (22kN) in the absence of
certication.
• The anchorage connector may be pulled in any direction shown in the LOADING
CONDITIONS DIAGRAM (pg. 9).
+
- Use a proper drill & bit for concrete. (SDS drill bit)
- Drill a 5/8” (16mm) hole no less than 4” (102mm) deep an 8” (203mm) away from
any edge.
- Hole must be straight & perpendicular to surface.
- Hole must be free of debris
- Concrete strength must be at least 3000psi (20.7MPa) and no less than 7”
(178mm) thick.
CONCRETE MOUNTING RACSWY050C:
Tensile Strength (UTS): 5,000-lbf (22kN)
Working Load (WLL): 1,000 lbs (454kg)
Maximum Capacity: One worker, 310 lbs (140 kg)
Weight: 1.2 lbs (544.31g)
Regulatory Compliance
ANSI Z359.1-2007, ANSI Z359.7-2011, OSHA 1910.66 , 1926.502

User Instructions - English
8
7”
(178mm)
min
drill 5/8” (16mm)Ø
8” (203mm)
min from any edge
Torque:
60ft-lbs
4” min (102mm)
180˚
360˚
8.0”ø
(203.2mm)
2.25”ø
(57.15mm)
5.5”
(139.7mm)
3.0”
(76.2mm)

User Instructions - English
9
LOADING CONDITIONS DIAGRAM
LOAD
ACCEPTABLE ACCEPTABLE IMPROPERACCEPTABLE
LOAD
LOAD
LOAD
Torque :
45 ft-lbs
(61 Nm)
1/2”-13 Lock Nut
1/2” Lock
Washer
1/2”-13 x 4”
Hex Bolt *
drill 1/2” (12.7mm)Ø
1/4”
(6mm)
min
3”(76mm)
min from any edge
Use
tapered
washer
STEEL MOUNTING

User Instructions - English
10
6.0 Stainless Steel Swivel Anchors
5,000 lbf/22kN
Model Numbers RACSWS100N-316 (swivel only), RACSWS100S-316 (Swivel anchor with
stainless steel mounting hardware), and RACSWS100C-316 (Swivel anchor with concrete
mounting hardware), RACSWS1SBA-316 (Stainless steel mounting hardware only), RACSWS-
1DNC-316 (Concrete mounting hardware only), RACDNC-TOOL (Concrete bolt assembly tool)
and RACSWP100N-316 (Weld Kit).
Warnings and Limitations
• Use only with Honeywell-approved personal fall arrest or restraint systems. The anchorage
must have the strength capable of supporting a static load, applied in the directions
permitted by the system, of at least 5,000-lbf (22kN) in the absence of certication.
• The anchorage connector may be pulled in any direction shown in the LOADING
CONDITIONS DIAGRAM (below)
8.0”ø
(203.2mm)
180°
360°
5.5”
(139.7mm)
2.25”ø
(57.15mm)
3.0”
(76.2mm)
1.0”
(25.4mm)
LOAD LOAD
LOAD
LOAD
LOADING CONDITIONS DIAGRAM
ACCEPTABLE ACCEPTABLE IMPROPER
ACCEPTABLE
Tensile Strength (UTS): 10,000-lbf (44kN)
Working Load (WLL): 1,000 lbs (454kg)
Maximum Capacity: One worker, 310 lbs (140 kg)
Weight: 1.2 lbs (544.3g)
Regulatory Compliance
ANSI Z359.1-2007, ANSI Z359.7-2011, OSHA 1910.66 , 1926.502

User Instructions - English
11
CONCRETE MOUNTING
- Use a proper drill & bit for concrete. (SDS drill bit)
- Drill a 7/8” (22mm) hole no less than 3” to 3-1/2“ (76mm-89mm) deep 9” (229mm)
away from any edge.
- Hole must be straight & perpendicular to surface.
- Hole must be free of debris
- Concrete strength must be at least 3000psi (20.7MPa) and no less than 7” (178mm)
thick.
-Drop expansion sleeve into hole.
-Use the Setting Tool by placing it in the hole resting on the expansion sleeve. Tap
tool until the blue inner sleeve is at the bottom of the expansion sleeve.
-Now place swivel over the hole and install the bolt provided.
drill 3/4” (19mm)Ø
9” (229mm)
min from any edge
7"
(178mm)
min.
TA
P
!!!
Torque Range:
30-40 ft-lbs
(22-30Nm)
Setting Tool
(DNC-TOOL)
Expansion
Sleeve
3” min 3-1/2” max
(76mm-89mm)
Embedment Depth

User Instructions - English
12
STEEL MOUNTING
Lock Nut
5/8” Lock
Washer
5/8”-11x4”
Hex Bolt *
Torque Range:
75 ft-lbs.
(100Nm)
drill 5/8” (16mm)Ø
* Use tapered washer with I-
beams that have tapered anges
3”(76mm)
min from any
edge
5/8”-11
* For steel applications a grade-5, 8 (or equivalent) bolt no shorter than 4” (100mm)
with a locking nut and washer must be used. Swivel anchor must be ush with steel
surface. A 16mm bolt may be used in place of a 5/8”-11 for metric applications.
1/4"
(6mm)
min.
WELD-ON MOUNTING
316 Stainless Steel 5/8”-
11 x 1-3/4” Bolt
* Weld
* Welding procedure must be approved by a Engineer or other
qualied person to be compatible with any and all structural &
operational characteristics of the selected installation location.
Torque:
85-ft lbs
(115Nm)
Puck

User Instructions - English
13
CONCRETE METALACCESSORIES
KIT CONTENTS PART NUMBER
RACSWS1SBA-316
(Steel Mounting Hardware Kit)
RACSWS100S-316
(Swivel with Steel Mounting kit)
RACSWS1DNC-316
(Concrete Hardware Kit)
RACSWS100C-316
(Swivel with Concrete Mounting Kit)
RACSWP100N-316KIT
(Weld-on Mounting Kit)
RACDNC-TOOL
(Concrete Anchor Tool)
+
+
+

User Instructions - English
14
7.0 Zinc Plated Swivel Anchors
10,000 lbf/44kN
Model Numbers RACSWY100N (Swivel only), RACSWY100S (Swivel anchor with steel mount-
ing hardware), and RACSWY100C (Swivel anchor with concrete mounting hardware), RAC-
SWY1SBA (Steel mounting hardware only), RACSWY1CSA (Concrete mounting hardware),
RACSWP100N-KIT (Weld kit) and RACSWX100N (Steel back plate).
Warnings and Limitations
• Use only with Honeywell-approved personal fall arrest or restraint systems. The anchorage
must have the strength capable of supporting a static load, applied in the directions
permitted by the system, of at least 10,000-lbf (22kN) in the absence of certication.
• The anchorage connector may be pulled in any direction shown in the LOADING
CONDITIONS DIAGRAM (Pg. 15)
8.0”ø
(203.2mm)
180°
360°
5.5”
(139.7mm)
2.25”ø
(57.15mm)
3.0”
(76.2mm)
1.0”
(25.4mm)
Tensile Strength (UTS): 10,000-lbf (44kN)
Working Load (WLL): 2,000 lbs (907kg)
Maximum Capacity: One worker, 310 lbs (140 kg)
Weight: 1.2 lbs (544.3g)
Regulatory Compliance
ANSI Z359.1-2007, ANSI Z359.7-2011, OSHA 1910.66, 1926.502

User Instructions - English
15
LOAD LOAD LOAD
LOAD
LOADING CONDITIONS DIAGRAM
ACCEPTABLE ACCEPTABLE IMPROPER
ACCEPTABLE
STEEL MOUNTING
Lock Nut
5/8” Lock
Washer
5/8”-11x4”
Hex Bolt *
Torque Range:
75-90 ft-lbs
(100-120 Nm)
1/4”
(6mm)
min.
drill 5/8” (16mm)Ø
* Use tapered washer with I-beams
that have tapered anges
3”(76mm)
min from any edge
5/8”-11
* For steel applications a grade-5, 8 (or equivalent) bolt no shorter
than 4” (100mm) with a locking nut and washer must be used.
Swivel anchor must be ush with steel surface. A 16mm bolt may be
used in place of a 5/8”-11 for metric applications.

User Instructions - English
16
CONCRETE MOUNTING
- Use a proper drill & bit for concrete. (SDS drill bit)
- Drill a 3/4” (19mm) hole no less than 5” (127mm) deep 9” (229mm) away from any edge.
- Hole must be straight & perpendicular to surface.
- Hole must be free of debris
- Concrete strength must be at least 3000psi (20.7MPa) and no less than 7” (178mm) thick.
7"
(178mm)
min.
drill 3/4” (19mm)Ø
9” (229mm)
min from any edge
Torque:
90ft-lbs
(120Nm) 4” min (102mm)
Embedment Depth
WELD ON MOUNTING
* Welding procedure must be approved by an Engineer or other qualied
person to be compatible with any and all structural & operational charac-
teristics of the selected installation location.
Grade - 5 or 8 bolt
5/8”-11 x 1-3/4”
Torque:
125-ft-lbs
(169Nm)
15/16” socket required
* Weld
3/8"min.
(9.5mm)
Puck

User Instructions - English
17
BACK PLATE MOUNTING
Torque Range:
to be determined
by an Engineer or
qualied person.
Back Plate to be used with 5/8” (16mm)
bolts or all thread. Drill hole perpendicu-
lar into surface so bolt can pass freely
through the substrate. Nut must be fully
threaded on the bolt to insure maximum
strength ratings and integrity of anchor.
* Bolt or All-thread and nut not included with Back Plate.

User Instructions - English
18
+
CONCRETE METALACCESSORIES
KIT CONTENTS PART NUMBER
+
+
RACSWY1SBA
(Steel Mounting Hardware Kit)
RACSWY100S
(Swivel with Steel Mounting kit)
RACSWY1CSA
(Concrete Hardware Kit)
RACSWY100C
(Swivel with Concrete Mounting Kit)
RACSWP100N-KIT
(Weld-on Mounting Kit)
RACSWX100N
(Backing Plate Only)

User Instructions - English
19
8.0 Hybrid Concrete Anchor
Model Number RACSWH100Y
Warnings and Limitations
• Use only with Honeywell-approved personal fall arrest or restraint systems. The anchorage
must have the strength capable of supporting a static load, applied in the directions
permitted by the system, of at least 10,000-lbf (22kN) in the absence of certication.
• The anchorage connector may be pulled in any direction shown in the LOADING
CONDITIONS DIAGRAM (Pg. 20)
5.5”
(139.7mm)
2.25”ø
(57.15mm)
3.0”
(76.2mm)
6-1/4”
(15.88cm)
1.0”
(25.4mm)
Compression
Bushing
Retaining
Bushing
Cable
Bolt
Spoon
Cone
Sleeve
8.0”ø
(203.2mm)
180˚
360˚

User Instructions - English
20
ACCEPTABLE ACCEPTABLE IMPROPERACCEPTABLE
LOAD LOAD
LOAD
LOAD
LOADING CONDITIONS DIAGRAM
DRILLING :
1. Use a hammer drill (SDS), drill a 1” (25mm) diameter hole at least 5”
(127mm) deep. The drilled hole must be straight and perpendicular to
the surface. Make sure the hole is of uniform diameter and free of peaks and
valleys on the inner wall. See diagram below.
2. Blow hole clean with compressed air.
3. Refer to the diagram below for hole location and requirements.
4. Always inspect the hole carefully when reusing a previously drilled hole.
5” min
depth
(12.7cm)
1”min
(2.54cm)
Section View:
10”
(25.4cm)
Drill 1ӯ
(2.54cm)
min from any edge
6”min
(15.24cm)
Hole to Edge:
Tensile Strength (UTS): 10,000-lbf (44kN)
Working Load (WLL): 1.000 lbs (454kg)
Maximum Capacity: One worker, 310 lbs (140kg)
Weight: 2.0-lbs (949g)
Regulatory Compliance: ANSI Z359.1-2007, ANSI Z359.7-
2011, OSHA 1910.66 , 1926.502