Honeywell FocusPro TH5320R User manual

FocusPRO®TH5320R
Wireless Thermostat
Termóstato inalámbrico
Thermostat Sans Fil
Operating Manual

® U.S. Registered Trademark. Patents pending.
Copyright © 2008 Honeywell International Inc. All rights reserved.
Read and save these instructions
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage,
do not operate cooling system when outdoor temperature is below 50°F (10°C).
Battery Holder
Press down and pull to
remove batteries.
Batteries should be
replaced once a year
(see page 11).

11
Contents Español: vea la página 15 •Français : voir la page 30
About your new thermostat
Initial setup ..................................2
Quick reference to controls ........3
Quick reference to display..........4
Operation
Fan settings (auto/on) ................5
System settings (heat/cool) ........6
Auto-changeover (heat/cool) ......7
Remote control............................8
Display outdoor climate..............9
Find lost remote control..............9
Compressor protection ............10
Appendices
Battery replacement..................11
In case of difficulty....................13
Limited warranty........................14
Regulatory information..............45

2
About your new thermostat
Your new wireless thermostat is pre-set for immediate use. All you have to
do is choose the settings you prefer:
1Select fan setting (Auto/On)....................................................See page 5
2Select system setting (Heat/Cool) .........................................See page 6

3
Quick reference to controls
Digital display (see page 4) Battery holder (see page 11)
Temperature buttons
Press to adjust temperature
Function buttons
Press to select the function displayed just above each button.
(Functions change depending on the task.)

Indoor Replace Battery Heat
Setting
75 75
System
Heat More
°°
Aux
Heat On
Fan
Auto
Quick reference to display screen
4
System setting
Heat/Cool/Auto/Off/Em
Heat (see page 6)
Fan setting
Auto/On (see page 5)
Current inside temperature Low battery warnings
(see pages 11-12)
System status
Heat On/Cool On
(If flashing, see p. 10)
Auxiliary heat
(Only for heat pumps
with auxiliary heat)
More
Press to view outdoor climate (if
outdoor sensor is installed), or to
find a misplaced remote control if
installed (see page 9)
Temperature setting

5
Select the fan setting
Press FAN to select Auto or On.
In “Auto” mode (the most commonly
used setting), the fan runs only when the
heating or cooling system is on.
If set to “On,” the fan runs continuously.
System
Heat More
Fan
Auto
System
Heat More
Fan
On
Note: Options may vary
depending on your heating/
cooling equipment.

6
Select the system setting
Note: Options may vary
depending on your heating/
cooling equipment.
Press SYSTEM to select:
•Heat: Thermostat controls only the
heating system.
•Cool: Thermostat controls only the
cooling system.
•Off: All systems are off.
•Auto: Thermostat automatically
selects heating or cooling depending
on the indoor temperature.
•Em Heat (only for heat pumps with
auxiliary heat): Thermostat controls
Emergency and Auxiliary Heat.
Compressor is locked out.
System
Heat More
Fan
Auto
System
Cool
More
Fan
Auto

7
Auto Changeover (heat/cool)
Auto Changeover is a feature used in
climates where both air conditioning and
heating are often used on the same day.
When the system is set to Auto, the ther-
mostat automatically selects heating or
cooling depending on the indoor
temperature.
Heat and cool settings must be at least 3
degrees apart. The thermostat will auto-
matically adjust settings to maintain this
3-degree separation.
Press until screen
displays “Auto”
Note: The Auto system setting
may not appear, depending on
how your thermostat was
installed.
System
Auto
More
Fan
Auto

8
Remote control
The optional remote control can act as a
mobile thermostat, to maintain a
comfortable temperature as you move
from room to room.
When the system is responding to
temperatures measured at the Remote,
the thermostat will display Remote has
Control.
Press CANCEL to restore temperature
control to the thermostat (the system will
only respond to temperatures measured
at the thermostat).
Temperature is measured at
location of remote control
Note: The thermostat may take up to 15 seconds to respond to commands entered at the
remote control. See Remote Control Operating Manual for more information.
72 75
Cancel
°°
Reading
at Remote
at Thermostat
Remote
has Control
More
Fan
Auto