Honeywell FocusPRO Wi-Fi TH6000 Series User manual

FocusPRO®Wi-Fi TH6000 Series
Programmable Thermostat
Installation
Guide
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Need Help?
For assistance with this product please visit http://customer.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
® U.S. Registered Trademark. Patents pending.
Copyright © 2012 Honeywell International Inc.
All rights reserved. 69-2738EFS-03
This manual covers the following models
• TH6320WF: For up to 3 Heat/2 Cool systems
System Types
• Gas, oil, or electric heat with air
conditioning
• Warm air, hot water, high-efficiency
furnaces, heat pumps, steam, gravity
• Heat only with fan
• Cool only

69-2738EFS—03 2
MCR29435
M29433
Wallplate installation
1. Separate wallplate from thermostat.
2. Mount wallplate as shown below.
Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.
Wall anchors
Wallplate
Wire hole Mounting screws
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do
not place the old control in the trash. Contact your local waste management
authority for instructions regarding recycling and proper disposal.
Insert reference card after wallplate is
mounted (see instructions, below).
MCR29434

3 69-2738EFS—03
Wiring
Wiring guide — conventional systems
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means and
overload protection as required.
[2] Remove jumper for 2-transformer systems.
[4] Common connection must come from cooling
transformer.
[5] In Installer Setup, set system type to Heat Only.
[6] In Installer Setup, set system type to
2Heat/2Cool Conventional.
[7] In Installer Setup, set changeover valve to O
or B.
[8] In Installer Setup, set system type to
2Heat/1Cool Heat Pump.
[9] In Installer Setup, set system type to
2Heat/2Cool Heat Pump.
[10] In Installer Setup, set system type to
3Heat/2Cool Heat Pump.
1H/1C System
(1 transformer)
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
W Heat relay
G Fan relay
Heat-only System
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common
W Heat relay
1H/1C System
(2 transformers)
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor
C 24VAC common [4]
W Heat relay
G Fan relay
Heat-only System
with Fan
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common
W Heat relay
G Fan relay
Cool-only System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
G Fan relay
2H/2C System
(1 transformer) [6]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24VAC common
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
2H/2C System
(2 transformers) [6]
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor (stage 1)
C 24VAC common [4]
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
See [notes] below
RcYWG RC
MCR29439
Rc
WR
C
MCR29440
RcWG RC
MCR29444
RcYG RC
MCR29445
RcYWGW2Y2 RC
MCR29446
RcYWG RC
M2944
3
RcYWGW2Y2 RC
M29447

69-2738EFS—03 4
1H/1C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
O/B Changeover valve [7]
G Fan relay
2H/1C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
O/B Changeover valve [7]
G Fan relay
Aux/E Auxiliary/Emergency heat relay
2H/1C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
O/B Changeover valve [7]
G Fan relay
Aux/E Auxiliary/Emergency heat relay
2H/2C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24 VAC common
O/B Changeover valve [7]
G Fan relay
Y2 Compressor contactor (stage 2)
3H/2C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24VAC common
O/B Changeover valve [7]
G Fan relay
Aux/E Auxiliary/Emergency heat relay
Y2 Compressor contactor (stage 2)
See [notes] below
MCR29448
RcY
GR
C
RcYGAux
E
LR
C
MCR29450
RcYGY2
LR
C
MCR29451
RcYGAux
E
LR
CY2
MCR29452
RcYGAux
E
LR
C
MCR29449A
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means and
overload protection as required.
[2] Remove jumper for 2-transformer systems.
[4] Common connection must come from cooling
transformer.
[5] In Installer Setup, set system type to Heat Only.
[6] In Installer Setup, set system type to
2Heat/2Cool Conventional.
[7] In Installer Setup, set changeover valve to O
or B.
[8] In Installer Setup, set system type to
2Heat/1Cool Heat Pump.
[9] In Installer Setup, set system type to
2Heat/2Cool Heat Pump.
[10] In Installer Setup, set system type to
3Heat/2Cool Heat Pump.
Wiring
Wiring guide — heat pump systems

5 69-2738EFS—03
W2 GWYR RCK Y2 C
MCR33878
HEAT PUMP
CONVENTIONAL
AUX/E GO/B YRRCK Y2 C
Conventional Terminal Letters:
Y2 2nd stage compressor contactor.
W2 2nd stage heat relay.
K Optional wirer save module.
Rc Cooling power. Connect to secondary side
of cooling system transformer.
R Heating power. Connect to secondary side
of heating system transformer.
W 1st stage heat relay.
Y 1st stage compressor contactor.
G Fan relay.
C Common wire from secondary side of
cooling transformer (if 2 transformers).
Heat Pump Terminal Letters:
Y2 2nd stage compressor contactor.
Aux/EAuxiliary/Emergency heat relay.
K Optional wirer save module.
Rc Cooling power. Connect to secondary side
of cooling system transformer.
R Heating power. Connect to secondary side
of heating system transformer.
O/B Changeover valve for heat pumps.
Y 1st stage compressor contactor.
G Fan relay.
C Common wire from secondary side of
cooling system transformer.
Terminal Designations
Wiring

69-2738EFS—03 6
Installer setup
1 Press Fan and s simultaneously and hold for
approximately 3 seconds. The screen will change
to display two numbers and the button designations
will be Done, Back, blank, Next.
2 Press Next until you see the function number—the
larger number on the left—you want to set.
3 Change options for any function by pressing sor
t until the correct option (smaller number on right)
is displayed.
4 Repeat Steps 2 and 3 until you have set all
functions that you wish to change.
5 When you have made all changes, press Done to
save and exit.
MCR33893A
HOLD
MCR33884
HOLD
Function Settings & Options
1Select System
Type
0 Heat/cool: Gas, oil or electric heating with central air conditioning.
1 Heat pump: Heat pump without backup or auxiliary heat.
2 Heat only: Gas, oil or hot water heat without central air conditioning.
3 Heat only with fan: Gas, oil or electric heat without central air
conditioning.
4 Cool only: Central air conditioning only.
5 Heat pump: Heat pump with backup or auxiliary heating.
6 Heat/Cool Multiple stages: 2 heat stages, 2 cooling stages.
7 Heat/Cool Multiple stages: 2 heat stages, 1 cooling stage.
8 Heat/Cool Multiple stages: 1 heat stage, 2 cooling stages.
9 Heat Pump Multiple Stages: 2 heat stages, 2 cool stages.
10 Heat Pump Multiple Stages: 3 heat stages, 2 cool stages.
2Heat Pump
Changeover Valve
(for heat pumps
only)
0 Cooling changeover valve: Use this setting if you connected a wire
labeled “O” to the O/B terminal.
1 Heating changeover valve: Use this setting if you connected a wire
labeled “B” to the O/B terminal.
3Heating Fan
Control
0 Gas or oil heat: Use this setting if you have a gas or oil heating system
(system controls fan operation).
1 Electric heat: Use this setting if you have an electric heating system
(thermostat controls fan operation).
5Heating Cycle
Rate
5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency).
9 Electric furnace: Electric heating systems.
3 Hot water or high-efficiency furnace: Hot water system or gas furnace
(more than 90% efficiency).
1 Gas/oil steam or gravity system: Steam or gravity heat systems.
[Other options: 2,4,6,7,8,10,11,12]
6Heating Cycle
Rate Stage 2
7Heating Cycle Rate
Auxiliary
91st stage compres-
sor cycle rate
3 Recommended for most compressors
[Other options: 1, 2, 4, 5 or 6 CPH]
10 2nd stage com-
pressor cycle rate

7 69-2738EFS—03
System setup
Function Settings & Options
12 Manual/Auto
Changeover
0 Manual changeover (Heat/Cool/Off).
1 Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat
or Cool based on room temperature. Note: System maintains minimum
3°F difference between heat and cool settings.
13 Adaptive Intelligent
Recovery (AIR)
1 On
0 Off
14 Temperature For-
mat (°F/°C)
0 Fahrenheit
1 Celsius
15 Compressor
protection
5 5 minute compressor off time
[Other options: 0, 1, 2, 3 or 4-minute off time]
16 Schedule Options 1 Program schedule is on (7-day programmable).
0 Program schedule is off. Thermostat can not be programmed.
26 Auxiliary Control 0 Comfort
1 Economy
27 Heat temperature
range stop
90 Max. heat temperature setting is 90°F (32°C)
[Other options: 40-89°F (4°C to 32°C)]
28 Cool temperature
range stop
50 Min. cool temperature setting is 50°F (10°C)
[Other options: 51-99°F (11°C to 37°C)]
32 Temperature
display offset
0 Thermostat displays actual room temperature
[Other options: -3, -2, -1, 1, 2, 3°F offset (-1.5°C to 1.5°C)]
36 Device Name
This name will
identify the
thermostat when
you view it remotely.
If you register
multiple thermostats,
give each one a
different name.
52 = Thermostat
1 Basement 16 Exercise Room 30 Library 44 Porch
2 Bathroom 17 Family Room 31 Living Room 45 Rec Room
3 Bathroom 1 18 Fireplace 32 Lower Level 46 Sewing Room
4 Bathroom 2 19 Foyer 33 Master Bath 47 Spa
5 Bathroom 3 20 Game Room 34 Master Bed 48 Storage Room
6 Bedroom 21 Garage 35 Media Room 49 Studio
7 Bedroom 1 22 Great Room 36 Music Room 50 Sun Room
8 Bedroom 2 23 Guest Room 37 Nursery 51 Theater
9 Bedroom 3 24 Gym 38 Office 52 Thermostat
10 Bedroom 4 25 Kid's Room 39 Office 1 53 Upper Level
11 Boat House 26 Kitchen 40 Office 2 54 Utility Room
12 Bonus Room 27 Kitchen 1 41 Pantry 55 Walk In Closet
13 Computer Room 28 Kitchen 2 42 Play Room 56 Wine Cellar
14 Den 29 Laundry Room 43 Pool Room 57 Workshop
15 Dining Room
38 Wi-Fi On/Off 1 Wi-Fi is on and can be connected to a Wi-Fi network.
0 Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you
are not connecting the thermostat to a Wi-Fi network this will remove the
text Wi-Fi Setup from the messaging center.
39 Wi-Fi Connection 1 Connected to Wi-Fi network. This is set automatically when the
thermostat is connected to the Wi-Fi network.
0 Set to 0 to disconnect from the Wi-Fi network.
42 Show period and
day of week
0 Period and day are not shown on the home screen.
1 Period and day are shown on the home screen.
85 Restore Schedule
Defaults
0 Continue using programmed schedule.
1 Restore thermostat program to energy saving settings
90 Restore Original
Settings
0 No
1 Disconnects thermostat from Wi-Fi and restores original settings (erases
customizations).

69-2738EFS—03 8
10 Heating system 0 Heat and fan turn off.
1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1,
5, 9 or 10 OR Setup Function 3 is set to 1 **See page 6
2 Stage 2 heat turns on
3 Stage 3 heat turns on
20 Emergency heating
system 0 Heat and fan turn off 1 Heat and fan turn on
30 Cooling system 0 Compressor and fan turn off
1 Compressor and fan turn on
2 Stage 2 compressor turns on
40 Fan system 0 Fan turns off
1 Fan turns on
Installer system test
10 0
MCR29455
Press s / t to turn system on/off.
Press NEXT to advance to next test.
Press DONE to terminate system
test.
Test number System status
To begin, press and hold the s and
t buttons until the display changes.
CAUTION: Compressor protection is bypassed during testing. To prevent
equipment damage, avoid cycling the compressor quickly.
System test System status

9 69-2738EFS—03
M33998
Troubleshooting
Lost Signal
If the no-Wi-Fi indicator displays in place of the Wi-Fi strength indicator in the upper right
hand corner of the home screen:
• Check another device to be sure Wi-Fi is working in your home; if not, call your
Internet Service Provider.
• Move the router.
• Restart the thermostat: remove it from the wallplate, wait 10 seconds, and snap it
back onto the wallplate. Return to Step 1 of Connecting to your Wi-Fi network.
Error Codes
For certain problems, the thermostat screen will display
a code that identifies the trouble. Initially, error codes are
displayed alone in the time area of the screen; after a
few minutes, the home screen is displayed and the code
alternates with the time.
Error Code Action
E01 During Wi-Fi Setup, the router
lost power.
• Ensureyourrouterhaspower.
• Iftryingtoconnecttoahiddenormanuallyaddednetwork,
confirm the router has power and is working.
E02 Invalid Wi-Fi password. This
code displays for 30 seconds,
then the thermostat will re-enter
Wi-Fi Setup mode.
• Re-enterpasswordforyourhomeWi-Finetwork.
• Repeatsetupprocessandconfirmyourpasswordforyourhome
Wi-Fi network.
E42 Router is not issuing an IP ad-
dress to the thermostat.
• Waitfor30minutes,
connection can take several
minutes.
• Ifstillnoconnection,remove
thermostat from wallplate for
10 seconds, then reconnect it.
• Verifyyourrouteriscorrectly
setup to automatically give IP
addresses.
E43 No internet connection. Thermo-
stat cannot communicate to Total
Connect Comfort.
• MakesuretheInternetcableispluggedin.
• Reboottherouter.
E99 General error Remove thermostat from wallplate for 10 seconds, then reconnect
it.
M33999

69-2738EFS—03 10
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions.
Most problems can be corrected quickly and easily.
Display is
blank
• Checkcircuitbreakerandresetifnecessary.
• Makesurepowerswitchatheatingandcoolingsystemison.
• Makesurefurnacedoorisclosedsecurely.
• MakesureCwireisconnected.
Fan does
not turn on
when heat is
required
• CheckFunction 3: Heating Fan Control to make sure it is set to match the
heating equipment.
Cool On or Heat
On is flashing
on the screen
• Compressorprotectionfeatureisengaged.Wait5minutesforthesystemto
restart safely, without damage to the compressor.
Heat pump
issues cool air
in heat mode,
or warm air in
cool mode
• CheckFunction 2: Heat Pump Changeover Valve to make sure it is properly
configured for your system.
Heating system
is running in
cool mode
• CheckFunction 1: System Type to make sure it is set to match the heating
and cooling equipment.
Heating
and cooling
equipment are
running at the
same time
• CheckFunction 1: System Type to make sure it is set to match the heating
and cooling equipment.
• Graspandpullthermostatawayfromwallplate.Checktomakesurebare
wires are not touching each other.
• Checkthermostatwiringiscorrect.