Honeywell PRO TH1000 Series User manual

Installation Manual
Guide d’installation
Guía de instalación
Série PRO TH1000 / TH2000 Series
Programmable and Non-programmable Thermostats
Thermostats programmables et non programmables
Termostatos programables y no programables

1
ENGLISH
/
PRO TH1000 / TH2000 Series
Programmable and Non-programmable Thermostats
This manual covers the following models:
System Types
TH1110D and TH1210D
non-programmable thermostats
TH2110D and TH2210D
programmable thermostats
(Remove thermostat from wallplate and turn over to find model number.)
TH1110D and TH2110D:
• Central heating (gas, oil, electric or high-
efficiency furnace)
• Central heating (see above) with air
conditioning
• Hot water system (steam or gravity) with or
without pump
• Central air conditioners
• 750 mV heating systems
• 1-Heat/1-Cool heat pumps
TH1210D and TH2210D:
• 2-Heat/1-Cool heat pumps
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502.

Installation Guide
2
ENGLISH
nLoosen the locking screw at the bottom of the thermostat. Note that the screw is
captive and cannot be removed from the wallplate.
oSeparate the thermostat from the wallplate as per Figure 1.
pPosition the wallplate against the wall and mark hole positions with a pencil.
NOTE: Levelling is for esthetics only and will not affect the performance of the
thermostat.
qDrill holes at the marked positions and insert supplied wall anchors.
rPass the wires through the large opening located at the bottom center of the wallplate
as per Figure 2.
sSecure the wallplate to the wall with supplied mounting screws as per Figure 3.
tConnect the wires to the terminals.
Wallplate installation
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power
before beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube,
do not place the old control in the trash. Contact your local waste
management authority for instructions regarding recycling and proper
disposal.
Figure 1
Figure 2 Figure 3

PRO TH1000 / TH2000 Series
3
ENGLISH
Gas, oil or electric heating and/or air conditioning (1H / 1C / 1H1C)
Heat pump without auxiliary heating (1H1C)
Heat pump with auxiliary heating (2H1C)
Wiring
Power supply. Provide disconnect means and overload protection as required.
Set the O/B jumper according to the type of reversing valve (see page 4).
Use a piece of wire (not supplied) to connect W and Y terminals to each other.
Optional 24 VAC common connection. If this connection is not made, use batteries
to power the thermostat.
This connection is not required for systems that provide heating only
This connection is not required for systems that provide cooling only
This connection is not required for systems that do have an air recirculating fan.
Use
TH1110D
or
TH2110D
Fan
Compressor
Heat
Use
TH1110D
or
TH2110D
Fan
Compressor
Reversing valve
Use
TH1210D
or
TH2210D
Fan
Compressor
Heat
Reversing valve

Installation Guide
4
ENGLISH
NOTE: This setting is necessary only if the thermostat is connected to a heat pump.
The jumper is located on the back of the thermostat faceplate. Set it according to the type
of reversing (changeover) valve used by the heat pump.
•O (factory setting): The reversing valve is energized when the System switch is set to
Cool (cooling mode).
•B: The reversing valve is energized when the System switch is set to Heat (heating
mode).
Incorrect jumper setting: The heat pump operation will be reversed; i.e., it will cool in
Heat mode and will heat in Cool mode.
NOTE: This setting is not applicable if a fan is not connected to the G terminal.
The jumper is located on the back of the thermostat faceplate. It determines how the fan
operates when placed in Automatic mode.
•HG (factory setting): Leave the jumper in this position for gas or oil heating systems. In
this position, the heating system controls the fan operation and activates the fan only
when the plenum air is sufficiently warm.
•HE: Place the jumper to this position for heat pump or electric heating systems. In this
position, the thermostat activates the fan only when there is a call for heat.
Incorrect jumper setting: An incorrect setting is noticeable
in a gas or oil heating system.
When heating starts, you will initially feel cold air coming out of the vents as the fan is running
before the furnace has enough time to heat up the air.
If 24 VAC common wire is connected to the C terminal, batteries are
optional and serve to provide backup power.
If 24 VAC common wire is not connected to the C terminal, batteries
are necessary to power the thermostat.
Install 2 AAA batteries on the back of the thermostat faceplate as
shown.
nAlign the two brackets on the top of the thermostat with the
corresponding slots on the top of the wallplate.
oPush the faceplate against the wallplate.
pTighten the screw at the bottom of the thermostat.
Reversing valve setting
Fan operation setting
Battery installation
Thermostat mounting

PRO TH1000 / TH2000 Series
5
ENGLISH
Follow the procedure below to personalize and
configure the thermostat according to the heating/
cooling system.
nPress Sand Tfor three seconds. The display
will appear as shown on the right.
oPress Sor Tto change the option.
pPress Sand Tfor three seconds to advance to
the next function.
qPress Run to exit the menu and save any
changes.
NOTE : You will also exit the menu if you press S and
T for three seconds when the last function is
displayed.
1Applicable to programmable models (TH2110D & TH2210D) only.
2Damage can occur if the compressor is restarted too soon after shutdown. This feature
forces the compressor to wait 5 minutes before restarting. During the wait time, the
message Cool On or Heat On flashes on the screen. When the safe wait time has elapsed,
the message stops flashing and the compressor turns on.
3Applicable to programmable models (TH2110D & TH2210D) only.
Adaptive Intelligent Recovery™ allows the thermostat to “learn” how long your furnace or
air conditioner takes to reach the set temperature. Simply program the desired times and
desired temperatures into the schedule. The thermostat will determine when to activate
heating or cooling so that the desired temperature is attained at the desired time.
Installer setup
Function Default
setting Options
1 Temperature display format 0 0: Fahrenheit
1: Celsius
2Time display format100: 12-hour display
1: 24-hour display
3 Heating cycles per hour 5
2 to 6 cycles per hour
• 2: 30 min (steam, gravity)
• 3: 20 min (hot water, 90%+ high-efficiency furnace)
• 4: 15 min (gas or oil)
• 5: 12 min (gas or oil)
• 6: 10 min (electric)
4 Cooling cycles per hour 3 2 to 6 cycles per hour
5Compressor protection200: enabled (for systems without a compressor))
1: disabled (for systems equipped with a compressor)
6Adaptive Intelligent Recovery310: Off
1: On
Function
number
Option
number

Installation Guide
6
ENGLISH
Temperature Ranges
• Heat: 40 °F to 90 °F (4.5 °C to 32 °C)
• Cool: 50 °F to 99 °F (10 °C to 37 °C)
Operating Ambient Temperature
• 32 °F to 122 °F (0 °C to 50 °C)
Shipping Temperature
• -40 °F to 130 °F (-40 °C to 55 °C)
Operating Relative Humidity
• 5% to 90% (non-condensing)
Physical Dimensions
• 4.7” H x 2.9” W x 1.1” D (120 mm H x 74 mm W x 28 mm D)
Power Supply
• 24 VAC or 2 AAA batteries
Maximum Load
• 1 A @ 24 VAC per output
Specifications

1
FRANÇAIS
/
Série PRO TH1000 / TH2000
Thermostats programmables et non programmables
Le présent guide porte sur les modèles suivants :
Types de système
Thermostats non programmables
TH1110D et TH1210D
Thermostats programmables
TH2110D et TH2210D
(Retirer le thermostat de la plaque murale et le retourner pour voir le numéro de modèle.)
TH1110D et TH2110D :
• Chauffage central (fournaise au gaz, mazout,
électrique ou à haut rendement)
• Chauffage central (voir ci-dessus) avec
climatisation
• Eau chaude (vapeur ou gravité) avec ou sans
pompe
• Climatiseur centrale
• Systèmes de chauffage 750 mV
• Thermopompes à 1 étage de chauffage / 1
étage de refroidissement
TH1210D et TH2210D :
• Thermopompes à 2 étages de chauffage / 1
étage de refroidissement
Doit être installé par un technicien d’expérience ayant reçu la formation pertinente.
Lire attentivement les instructions. Le fait de ne pas les suivre
risque d’endommager le produit ou de présenter un danger.
Besoin d’aide?
Pour obtenir de l’assistance au sujet de ce produit, consulter le http://yourhome.honeywell.co
m
ou téléphoner sans frais au Centre de service à la clientèle de Honeywell au 1 800 468-1502 .

Guide d’utilisation
2
FRANÇAIS
nDesserrer la vis de blocage au bas du thermostat. Noter que la vis est captive et ne
peut pas être enlevée de la plaque murale.
oSéparer le thermostat de la plaque murale selon la figure 1.
pPlacer la plaque murale contre le mur et marquer au crayon l’emplacement des trous.
NOTA : La mise à niveau est pour l’esthétique uniquement et n'affectera pas le
fonctionnement du thermostat
qPercer les trous aux endroits marqués et insérer les chevilles d’ancrage fournies.
rPasser les fils par la grande ouverture située au centre inférieur de la plaque murale
selon la figure 2.
sFixer la plaque murale au mur avec les vis de montage fournies selon la figure 3.
tRelier les fils aux bornes.
Installation de la plaque murale
MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE
Peut provoquer des chocs électriques ou endommager le matériel. Couper
l’alimentation électrique avant d’effectuer le raccordement.
AVIS SUR LE MERCURE
Si le nouveau thermostat remplace un ancien régulateur contenant un
contact à mercure, ne pas jeter l’ancien régulateur aux poubelles.
Communiquer avec le service local de cueillette des déchets pour obtenir
de l’information sur le recyclage ou sur la bonne façon de disposer d’un
ancien régulateur contenant un contact à mercure.
Figure 1
Figure 2 Figure 3