Hopeland CL7206A5 User manual





CL7206A5RFIDReadermodule
Usermanual



ShenzhenHopelandTechnologiesCo.,Ltd




















WelcometobetheuserofHopelandRFIDproducts.
ThanksforchoosingHopelandRFID’sMulti-functional
ReaderModuleCL7206A5.Webelieveourdevicewill
bringconvenienceforyourwork.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. such modifications could void the user’s authority to operate this
equipment
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
The distance between user and products should be no less than 20cm

CE Note
Manufacturer: SHENZHEN HOPELAND TECHNOLOGIES CO., LTD.
Address: 17/F, Block A, Clou Bldg, Baoshen Road, Hitech Industrial Park North, Nanshan
District,518007, Shenzhen, China
Hereby, SHENZHEN HOPELAND TECHNOLOGIES CO., LTD. declares that this device is in
compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU
Importers: XXXXXXX
Address: XXXXXXX
A copy of the declaration of conformity can be obtained with this user manual; This product is not
restricted in the EU.
The wireless operation frequency is 865.7MHz to 867.5MHz. The Max ERP Power is 26.24dBm
The distance between user and products should be no less than 20cm.


Catalogue
1.SPECIFICATION ................................................................................................................................................................................... 6
1.1PRODUCTFEATURES ............................................................................................................................................................................... 6
1.2MAINFUNCTIONSANDTECHNICALFEATURES .......................................................................................................................................... 6
1.2.1Mainfunctions ......................................................................................................................................................................... 6
1.2.2Features ..................................................................................................................................................................................... 6
1.2.3Workingenvironment ............................................................................................................................................................. 6
2.EXTERNALINTERFACE ....................................................................................................................................................................... 8
2.1SIZE ....................................................................................................................................................................................................... 8
2.2INTERFACEPHOTOGRAPH ....................................................................................................................................................................... 8
2.3INTERFACEDEFINITION .......................................................................................................................................................................... 9
3.INSTALLATIONMANUAL ................................................................................................................................................................. 10
3.1ATTENTIONS ........................................................................................................................................................................................ 10
3.2INSTALLATIONCONDITIONS .................................................................................................................................................................. 10
3.3DEVICECONNECTION ........................................................................................................................................................................... 10
3.3.1Connectpoweradapter ....................................................................................................................................................... 10
3.3.2ConnectPC .............................................................................................................................................................................. 11
3.4DEVICEINSTALLATION .......................................................................................................................................................................... 11
4.OPERATIONINSTRUCTIONS ........................................................................................................................................................... 12
4.1DEMOSOFTWAREINSTRUCTIONS ......................................................................................................................................................... 12
4.2DEMOSOFTWAREAPPLICATIONENVIRONMENT .................................................................................................................................... 12
4.3DEMOSOFTWAREVERSION .................................................................................................................................................................. 12
4.4DEMOSOFTWAREOPERATION .............................................................................................................................................................. 12
4.4.1Connecttoreader .................................................................................................................................................................. 12
4.4.1.1Serialcommunicationconnection ............................................................................................................................. 1 2 

4.4.1.2Networkportcommunicationconnection ....................................................................................................
4.4.1.3RS485communicationconnection ............................................................................................................................ 15
4.4.2DATADISPLAYAREA .......................................................................................................................................................................... 15
4.4.2.1READEPC .................................................................................................................................................................................... 16
4.4.2.2READTID ..................................................................................................................................................................................... 17
4.4.2.3Customread ................................................................................................................................................................... 17
4.4.2.4Stopread ......................................................................................................................................................................... 18
4.4.3Writedata ............................................................................................................................................................................... 18
4.4.3.1WriteEPCdata ............................................................................................................................................................... 18
4.4.3.2Writeuserdata .............................................................................................................................................................. 19
4.4.3.3Customtagaction ......................................................................................................................................................... 20
4.4.4TCPserver/clientmode ...................................................................................................................................................... 20
4.4.6Frequencyhoppingmanagement ...................................................................................................................................... 21
4.4.7Labelfiltering .......................................................................................................................................................................... 22
4.4.8Autoidleconfiguration ......................................................................................................................................................... 23
4.4.9GPI/OConfiguration .............................................................................................................................................................. 24
4.4.10.Advancedconfiguration .................................................................................................................................................... 25
4.4.11Tools ....................................................................................................................................................................................... 26
5. COMMON FAILURES ................................................................................................................................................................. 29
5.1 DAILY MAINTENANCE .................................................................................................................................................................... 29
5.2 COMMON FAILURE ANALYSIS AND SOLUTION ........................................................................................................................... 29
6.ACCESSORY ....................................................................................................................................................................................... 31
6.1ACCESSORY .......................................................................................................................................................................................... 31
6.2STORAGE ENVIRONMENT ............................................................................................................................................................. 31
7.HOST INFORMATION ................................................................................................................................................................ 32
8.AFTER-SALE SERVICE ............................................................................................................................................................ 33

1.Specification
1.1Productfeatures
CL7206A5isaUHFRFIDreadermodule,partnerwithCL7206D2.
1.2Mainfunctionsandtechnicalfeatures
1.2.1Mainfunctions
HardwarepartnerwithCL7206D2
Telecommunicationport:RS232,RS485,Enternetport,USB
IOinterface:1forIOinput,2forIOoutput,1forwiegandoutput,IOoutand
wiegandissameport.
IOinterface’slevelfluctuationtriggerthereadingfunction(Responsetime:
<10ms)
PowerbyadapterandUSB
1.2.2Features
Internetportspeedrate:10M/100Mautomatic.
RS232serialrate:115200bps(default),19200bps,9600bps
RS485rate:115200bps(default),19200bps,9600bps
Operateunderlowtemperature‐20±3℃for48hours(readtags),backtoindoor
temperaturereadtagsnormally.
Operateunderhightemperature‐70±3℃for48hours(readtags),backtoindoor
temperaturereadtagsnormally.
1.2.3Workingenvironment
Workingtemperaturerange:‐20℃～+70℃

Relativehumidity:5%RH～90%RH（+25℃）


2.Externalinterface
2.1Size
105mm×95mm×18mm(excludingaccessories)
2.2Interfacephotograph

DevelopmentboardcanbecompatiblewithCL7206D22portmodule.Developmentboardpowerup
throughpowerport,andcommunicatewithUSB/RS232/Networkport.


2.3InterfaceDefinition
RJ45 InterfaceDefinitionform
LinearColorDefinition
1White,greenEthernetdatatransmittingpositiveend
2greenEthernetdatatransmittingnegativeend
3White,orangeEthernetdatareceivingpositiveend
4Blue5Vpowerinput
5White,bluePowerground
6OrangeEthernetdatareceivingnegativeend
7White,brownRS485positive
8BrownRS485negative

RS232InterfaceDefinitionform
LinearDefinition
1NC
2RXD
3TXD
4NC
5GND
6NC
7GPI1
8GPO1/Wiegand0
9GPO2/Wiegand1

3.Installationmanual
3.1Attentions
Toensurethenormalandstableoperationofthedeviceandyourpersonal
propertyandsafety,pleasecarefullyreadthefollowingnotesbeforeinstallCL7206A5
module:
1.Firstly,checkwhetherthepowersocketisconnectedtotheground,andtosee
whetherthelocalpowersupplyvoltageisinaccordancewiththeapplicablevoltage
rangeofthereader;
2.Checkthedeviceandtheexternalconnectionifiscloselyconnected;
3.Payattentiontothetypeselectionandthelengthlimitofthecableandtheserial
line:
Seriallineconnectdirectly,nolongerthan5meters
RS485Cableconnectdirectly,nolongerthan80meters
Networkcableconnectsnolongerthan80meters.
4.Wheninstallingseveralreaders,theantennapositionandtheantennaspacing
shouldbeappropriatetoavoidinterferencewitheachother.
3.2Installationconditions
Beforeinstallingthereader,pleasecarefullycheckiftheproductisingood
condition,theaccessoriesarecompleteornot,ifthereisanydamage,pleasecontact
thesupplier.
3.3Deviceconnection
3.3.1Connectpoweradapter

☆InsertthepowercordintotheACpowersupplysocketandpluganotherend
intothepowerconnectorofthedeviceandtighten.
☆Turnonandwaitabout20seconds,thesysteminitializationprocessis
completedandisstandbystate.
3.3.2ConnectPC
☆DevelopmentboardcomeswithRS232,networkport,USBport,RS485port.
☆ RS232andUSBinterfaceisforshortdistancecommunication(lessthan5m),
throughtheDB9connectorandthePCserialportconnectiontorealizethe
communicationofPCandthedevice.
☆RS485usedforlongdistancecommunication(lessthan80m)
☆ RJ45networkportusedforlongdistancecommunication(lessthan80m)
3.4Deviceinstallation
Installthedevelopmentboardaccordingtouser’ssituation,itcanuseonlyone
RJ45portforpowerandcommunication;pleaserefertotheRJ45portdefinition
form.
ThedevelopmentboardcanbepoweredbyadapterandUSB,communicated
withPCbyRJ45,RS232/RS485andUSB.

4.Operationinstructions
4.1Demosoftwareinstructions
DemosoftwareforCL7206A5ismainlyusedforsystemcontrol,communication
model,configurationsettingandinquiring,readingtagsanddatadisplayingetc.
4.2Demosoftwareapplicationenvironment
Softwareenvironment
Windows2000ServicePack3,WindowsServer2003,WindowsXPServicePack
2,Windows7OS
Hardwareenvironment
PCwithP4/1.7GHzabove，512Morabove,40Ghardware
4.3Demosoftwareversion
DemoV1.0.4
4.4Demosoftwareoperation
4.4.1Connecttoreader
Allfunctionsareavailableonlyafterconnectedsuccessfully
4.4.1.1Serialcommunicationconnection
Afterconnectedthereaderwithpowerandcommunicationcable(serialportor
networkcable),openthedemosoftware,iftheiconsonmainManuaregrey,means
thereaderisnotconnected.Inthe‘connectingreader’optionlistselect
communicationmode‘serialconnection’,‘connectionparameters’select‘COM?’
(ChoosePCserialnumber),communicationrateselect115200(default),clickOK

button,asshowninimage4‐1.
 
Image4‐1Serialcommunicationconnection
Iftheconnectionissuccessful,alltheiconsinthetoolbarareilluminated,as
showninimage4‐2,meanstheserialcommunicationconnectionissuccessful.

Imag4‐2serialportcommunicationconnectsuccessful

4.4.1.2Networkportcommunicationconnection
Networkportusedforlongdistanceconnection(within80m),connecttothe
routerthroughcableandswitcher,orconnectedwiththePCnetworkportdirectly.
Selectthecommunicationmode"TCPconnection"inthe"connectreader"optionlist,
"connectparameter"inputreaderIP(default192.168.1.116),enterthe
communicationportnumber(default9090),andclickOKbutton,asshowninimage
4‐3

Image4‐3Networkportcommunicationconnection
ThedevicehasbeenwrittenIPaddress192.168.1.116asdefault.Ifyouforgetor
needtomodify,usingserialconnection"connection"afterconnectsuccessfully,then
youcanfoundthecurrentIPaddressthroughselect“settings”>"senior">
“configuration”,setuptheIPaddressin“Networkportsettings”when“configuration”
dialogpopsup.Seeimage4‐4.
Note:TheIPaddressofthereadercan’tberepeated.UsethePingcommandto
testwhetherthenetworkisconnectedonPC.


image4‐4.Readersetting
4.4.1.3RS485communicationconnection
Selectthecommunicationmodeinthe"connecttothereader"option"485
connection(serialport)","connectparameter"select"COM?"(selectPCserial
number),communicationrateselect"115200",entertheRS485address,thenclick
OK,asshowninimage4‐5
 
Image4‐5485communicationconnection
RS485addressdefaultsto1
RS485addressrange1~255
4.4.2Datadisplayarea


Image4‐6Datadisplayareaparametermeanings
Type:Tagstype:6C
EPC:Tags’EPCdata,readandwritable
TID:theTIDdataofthelabel,theonlylogo,readonly
UserData:userdataareacanbereadandwrite.
ReserveData:reservedareadata,storethepassworddata,etc.
TotalCount:totalnumberoftags
ANT1:thereadingtimesofNO.1antenna
RSSI：SignalIntensity
4.4.2.1ReadEPC
Clickthebutton ,thedatadisplayareawilldisplaythecurrentreadEPCdata,
themostlengthfortheEPCis240bits.
EPCdisplayashexadecimalcharacterstring,usethewordaslengthunit(1word=
2bytes=4hexadecimalcharacter)
IfyouwanttoreadtheEPCdataofthecustomlength,pleaserefertochapter

4.4.2.3customread

4.4.2.2ReadTID
Clickthebutton ,thedatadisplayareawilldisplaythecurrentreadEPCand
TIDdata
TIDdatadisplayashexadecimalcharacterstring,usethewordaslengthunit(1
word=2bytes=4hexadecimalcharacter).
TIDlength,thedefaultis6words.
IfyouwanttoreadtheTIDdataofthecustomlength,pleaserefertochapter
4.4.2.3customread
4.4.2.3Customread
Clickthebutton ,pop‐updialogbox,asshowninImage4‐7&4‐8

Image4‐76Ctagsetting

Select"6Ctagconfiguration"

Matchingread,youcanmatchingreadthroughknownEPCdataorTIDdataoftags.
ReadTID,selecttoreadthetagTIDdata,thereadmodedefaultas"adaptation",
usethewordaslengthunit.
Readtheuserarea,selecttoreadthetaguserareadata,usethewordasthe
startingaddressandreadlengthunit
Readthereservedarea,selecttoreadthetagretainsdata,usethewordasthe
startingaddressandreadlengthunit.

Image4‐86Btagsetting
4.4.2.4Stopread
Click button stop all read and write operations.
4.4.3Writedata
4.4.3.1WriteEPCdata
Clickbutton andpopupdialogboxasshowninimage4‐9:


Image4‐9WriteEPCdata
Selectalabeldata(containsTIDinformation)hasbeenread,fillintheEPCdata(16
hexstring),click"OK".
4.4.3.2Writeuserdata
Clickbuttonandpopupdialogboxasshowninimage4‐10:


Image4‐10writeuserdata
Selectalabeldata(containsTIDinformation)hasbeenread,fillintheuserdata(16
hexstring),click"OK".
4.4.3.3Customtagaction
Clickbuttonandpopupdialogboxasshowninimage4‐11:

Image4‐11Customtagaction
1.Selectatagdatathathasbeenread;
2.Clickthe"customoperation"button;
3.Takedetailedactiontowrite/lock/destroytagaccordingtothereaderprotocol
4.4.4TCPserver/clientmode
Selectconfigurationonthemaindemointerface>"readandwrite
configuration>"TCPserver/clientmode",pop‐updialogbox,asshowninImage
4‐12: