ICP DAS USA tPET-P6 User manual

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1
tET/tPET-P6
6 Digital Input channels Tiny Ethernet module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/tet_p6
1. What’s in the shipping package?
The package includes the following items:
tET/tPET-P6
Software CD
Quick Start
(This Document)
2. Preparations for devices
1. Power Supply:+12 ~ +48 VDC
2. Ethernet Hub.(PoE Ethernet Switch for tPET module only)
3. Make sure your PC has workable network settings.
4. Disable or well configure your Windows firewall and Anti-Virus firewall
first, else the “Search Servers”on page 6 may not work. (Please
contact with your system Administrator)
1

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2
3. Connecting the Power and Host PC
1. Check Init/Run Switch is on “RUN” position.
2. Connect both the tET/tPET-P(D)6 and your computer to the same sub
network or the same Ethernet Switch, and power tET/tPET-P(D)6 on.

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3
4. Pin Assignments and Wiring Note

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4
Wire the DI for self-test. The wiring as follows:

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5
DI/DO Modbus Address:
(1xxxx) DI address:
Bits
Access
Begin address
Points
Description
per
Range
Type
Point
0
1~6
Digital Input
1
0:Off
R
(0x0)
1:On
32
1~6
Digital latched status
1
0:no
R
(0x20)
(high)
1:latched
64
1~6
Digital latched status
1
0:no
R
(0x40)
(low)
1:latched
(0xxxx) DO address:
Bits
Access
Begin address
Points
Description
per
Range
Type
Point
32
1
Clear all DI latched
1
1: Clear
W
(0x20)
status (high)
33
1
Clear all DI latched
1
1: Clear
W
(0x21)
status (low)
150
1
Enable All DI latched
1
0:Disable
R/W/F
(0x96)
status (high/low)
1:Enable
151
1~6
Enable high speed
1
0:Disable
R/W/F
(0x97)
digital counter
1:Enable
.
.
.
.
.
.
.
.
.
.
.
.
32
1
Clear all DI latched
1
1: Clear
W
(0x20)
status (high)
•For detail “DI/DO Modbus Address” information, please refer to section 6.3 Modbus
Register Map of user’s manual in CD:\NAPDOS\tPET\Document\

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6
5. Configuring Ethernet Settings
1
1. Run the eSearch Utility.
The eSearch Utility is located at:
CD:\Napdos\Software\eSearch\
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/
2. Click “Search Servers”button to search your tET/tPET-P(D)6.
3. Double-Click your tET/tPET-P6 to configure the settings.
4. Contact your Network Administrator to get correct network
configuration. Modify the network settings and then click “OK” button.
The tET/tPET-P6 will restart it-self immediately.
4

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7
6. Testing your tET/tPET Module
1. Wait 2 seconds and then click the “Search Servers”button again to
ensure the tET/tPET-P6 is working well with new configuration.
2. Click the “Web”button to link the tET/tPET-P6 web server.
3. Enter the password and click the “Submit”button to enter the
configuration web page. (The factory default password: Admin)
3

tET-P6 6 DI channels Tiny Ethernet module - QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 8
4. Control the I/O for simple test.
Step 1: Open the power supply as DI0 input.
Step 2: In the “Home” page, check that the “DI0” status should show
current status is “ON”.
8