Horizon Hobby Bind-N-Fly AS3X UMX A-10 User manual

UMX™A-10
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni

2
EN
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product,
personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires
some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. Do not use with incompatible components or alter this product in any way outside
of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to
assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential
harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage,
collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage
AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND
little or no possibility of injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion
of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the
support tab for this product.
•Always keep a safe distance in all directions
around your model to avoid collisions or injury.
This model is controlled by a radio signal subject
to interference from many sources outside your
control. Interference can cause momentary loss
of control.
•Always operate your model in open spaces away
from full-size vehicles, traffic and people.
•Always carefully follow the directions and
warnings for this and any optional support equip-
ment (chargers, rechargeable battery packs, etc.).
•Always keep all chemicals, small parts and
anything electrical out of the reach of children.
•Always avoid water exposure to all equipment
not specifically designed and protected for this
purpose. Moisture causes damage to electronics.
•Never place any portion of the model in your
mouth as it could cause serious injury or
even death.
•Never operate your model with low transmitter
batteries.
•Always keep aircraft in sight and under control.
•Always use fully charged batteries.
•Always keep the transmitter powered on while
aircraft is powered.
•Always remove batteries before disassembly.
•Always keep moving parts clean.
•Always keep parts dry.
•Always let parts cool after use before touching.
•Always remove batteries after use.
•Always ensure failsafe is properly set
before flying.
•Never operate aircraft with damaged wiring.
•Never touch moving parts.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings

3
EN
To register your product online, go to www.e-fliterc.com
20.3 (516mm)
22.1 in (562mm)
5.9 oz
(168 g)
Transmitter and Receiver Binding..........................4
Low Voltage Cutoff (LVC) .......................................4
ESC/Receiver Arming, Battery Installation and
Center of Gravity...................................................5
Control Centering .................................................6
Factory Control Horn Settings................................6
Dual Rates and Expos ...........................................6
Landing Gear Removal..........................................7
Control Direction Test............................................8
AS3X Direction Test...............................................9
Flying Tips and Repairs.......................................10
Motor Service .....................................................11
Post Flight Checklist ...........................................12
Troubleshooting Guide ........................................12
Troubleshooting Guide (Continued)......................13
Limited Warranty ................................................13
Warranty and Service Contact Information ..........15
IC Information.....................................................15
FCC Information..................................................15
Compliance Information for the European Union..16
Replacement Parts..............................................59
Optional Parts and Accessories ...........................60
Table of Contents
Specifications
Wing Area: 83.7 sq. in.
(5.40 dm2)
Preflight Checklist
Installed
(2) Motors: BL180M, 13500Kv inrunner
brushless motor
Receiver: DSMX®UM 6-Ch AS3X®w/
Twin Brushless ESC
(4) 2.3-Gram Performance Linear Long
Throw Servo (SPMSA2030L)
Required to Complete
Recommended Battery: 800mAh 2S
7.4V 30C Li-Po (EFLB8002SJ30)
Battery Charger: Prophet™Sport Plus
50W AC/DC Charger (DYNC2010CA);
Charger Lead with JST Female
(EFLA230)
Recommended Transmitter:
Full range Spektrum™DSM2®/DSMX®
with dual-rates (DXe and up)

1. Charge flight battery.
2. Install flight battery in aircraft (once it has
been fully charged).
3. Bind aircraft to transmitter.
4. Make sure linkages move freely.
5. Perform Control Direction Test with
transmitter.
6. Perform AS3X Control Direction Test with
aircraft.

7. Set dual rates.
8. Adjust center of gravity.
9. Perform a radio system Range Check.
10. Find a safe and open area.
11. Plan flight for flying field conditions.
12. Set flight timer for 5 minutes for first flight.

4
EN
For a list of compatible DSM2/DSMX transmitters, please visit www.bindnfly.com
Transmitter and Receiver Binding
For subsequent flights, power ON the transmitter for 5 seconds before connecting the flight battery.
Binding Procedure
CAUTION: When using a Futaba transmitter with a Spektrum DSM®module, you must reverse the
throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions.
Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
1. Refer to your transmitter’s unique instructions for binding to a receiver (location of transmitter’s
Bind control).
2. Make sure the flight battery is disconnected from the aircraft.
3. Ensure the transmitter is powered OFF.
4. Connect the flight battery to the aircraft and turn the aircraft upright. The receiver LED will begin to
flash (typically after 5 seconds).
5. Ensure that control surface trims are centered and the throttle and throttle trims are in the low
position to correctly set the failsafe.
6. Put your transmitter into bind mode. Refer to your transmitter’s manual for binding button or switch
instructions.
7. After 5 to 10 seconds, the receiver status LED will turn solid, indicating that the receiver is bound
to the transmitter. If the LED does not turn solid, refer to the Troubleshooting Guide at the back of
the manual.
When a Li-Po battery is discharged below 3V per
cell, it will not hold a charge. The aircraft’s ESC
protects the flight battery from over-discharge
using Low Voltage Cutoff (LVC). Once the battery
discharges to 3V per cell, the LVC will reduce the
power to the motor in order to leave adequate
power to the receiver and servos to land the
aircraft.
When the motor power decreases, land the aircraft
immediately and replace or recharge the flight
battery.
Always disconnect and remove the Li-Po battery
from the aircraft after each flight. Charge your Li-Po
battery to about half capacity before storage. Make
sure the battery charge does not fall below 3V per
cell. Failure to unplug a connected battery will result
in trickle discharge.
For your first flights, set your transmitter timer
or a stopwatch to 5 minutes. Adjust your timer for
longer or shorter flights once you have flown the
model.
NOTICE: Repeated flying to LVC will damage the
battery.
Low Voltage Cutoff (LVC)

5
EN
ESC/Receiver Arming, Battery Installation and Center of Gravity
1-2-3-4-5 Sec.
4
3
2
1
NOTICE: Always keep material or debris away
from the intake. When armed, the rotor will turn in
response to throttle movement and could ingest in
any loose objects.
Arming the ESC/receiver also occurs after binding
as previously described, but subsequent connection
of a flight battery requires the following steps.
1. Lower the throttle and throttle trim to the
lowest settings on your transmitter.
2. Remove the battery/canopy hatch from the
fuselage and install a flight battery (A) all the
way to the back of the battery comportment.
Center of Gravity (CG)
The CG location is 34-36mm back from the leading
edge of the wing at the root. Balance the airplane
inverted on this recommended CG mark with all
landing gear installed. Adjust as needed by sliding
the battery forward or back.
3. Power on your transmitter, then
wait 5 seconds.
4. Connect the battery to the ESC, noting proper
polarity. Keep the plane immobile and away
from wind for 5 seconds to allow the AS3X
system to initialize.
A successful connection is indicated by:
– A series of tones
– A continuous LED
CAUTION: Always disconnect the Li-Po
battery from the ESC when not flying to eliminate
power supplied to the motor. The ESC does not
have an arming switch and will respond to any
transmitter input when a signal is present.
CAUTION: Always disconnect the Li-Po
battery from the ESC when not flying to avoid
over-discharging the battery. Batteries discharged
to a voltage lower than the lowest approved
voltage may become damaged, resulting in loss of
performance and potential fire when batteries
are charged.
34-36mm
A

6
EN
Before the first flights, or in the event of an
accident, make sure control surfaces are
centered when the transmitter controls and
trims are neutral. The transmitter sub-trim must
be set to zero. Adjust the linkages mechanically
if the control surfaces are not centered. Use of the
transmitter sub-trims may not correctly center the
aircraft control surfaces due to the mechanical
limits of linear servos.
•Make the U-shape narrower to make the
connector shorter. Make the U-shape wider to
make the linkage longer.
Control Centering
Factory Control Horn Settings
The illustration shows the factory settings for
linkages on the control horns. Linkage connections
on the control horns directly affect aircraft response.
Rudder Ailerons Elevator
Dual Rates and Expos
To obtain the best flight performance, we
recommend using a DSM2/DSMX transmitter
capable of Dual Rates and Expo. Before binding,
ensure that you are starting with a blank acro
model in your transmitter. Set wing type and servo
reversing to normal.
The suggested settings shown here are the
recommended starting settings. Adjust according to
the individual preferences after the initial flight.
NOTICE: Do not set your transmitter travel adjust
over 100%. If the TRAVEL ADJUST is set over
100%, it will not result in more control movement, it
will overdrive the servo and cause damage.
It is normal for linear servos to make significant
noise. The noise is not an indication of a faulty
servo.
Tip: For landing, we recommend using high rate
elevator.
Dual Rates Expos
High Low High Low
Aileron 100% 70% 10% 0%
Elevator 100% 70% 10% 0%
Rudder 100% 70% 10% 0%

7
EN
Landing Gear Removal
Carefully pull the gear straight out of the retainer
clip that secures it into the fuselage.
When needed, assemble in reverse order.
When the landing gear is reinstalled, make sure
the nose gear is angled forward as shown.

8
EN
Control Direction Test
You should bind your aircraft and transmitter
before doing these tests.
Move the controls on the transmitter to
make sure the aircraft control surfaces
move correctly and in the proper direction.
Make sure the tail linkages move freely
and that paint or decals are not adhered
to them.
Transmitter
Command Aircraft Reaction
ElevatorAileronRudder
Down
Elevator
Up
Elevator
Right
Roll
Left
Roll
Right
Rudder
Left
Rudder
Arrows indicate the direction of the trailing edge of the control
surface.

9
EN
Transmitter
Command Aircraft Reaction
ElevatorAileronRudder
AS3X Direction Test
You should bind your aircraft and
transmitter before doing these tests.
Move the controls on the transmitter to
make sure the aircraft control surfaces
move correctly and in the proper direction.
Make sure the tail linkages move freely
and that paint or decals are not adhered
to them.
Aircraft
movement AS3X Reaction
Arrows indicate the direction of the trailing edge of the control
surface.
F-16 manual

10
EN
Flying Tips and Repairs
Range Check your Radio System
After final assembly, range check the radio system
with the aircraft. Refer to your specific transmitter
instruction manual for range test information.
Flying
We recommend flying your aircraft outside in no
greater than moderate winds or inside in a very
large indoor facility. Always avoid flying near houses,
trees, wires and buildings. Be careful to avoid flying
in areas where there are many people, such as busy
parks, schoolyards or soccer fields. Consult local
laws and ordinances before choosing a location to
fly your aircraft.
Hand Launching
Hold the aircraft just behind the wings. Apply full
throttle with a little up elevator and give a firm toss
directly into the wind with the nose pointed slightly
up (5–10 degrees above the horizon). After the model
gains altitude, decrease the throttle as you desire.
The A-10 has a high thrust line. If the model is not
launched with enough airspeed or the throttle is
added quickly at very low airspeed the aircraft will
pitch down slightly. Adding some up elevator trim
for the first few hand launches is recommended,
until you are comfortable with the launching
characteristics of this aircraft.
Tip: The electric ducted fans (EDF) acts like a jet
aircraft, so control is generated by airspeed rather
than air from a propeller moving over the control
surfaces.
Takeoff
Taxi the aircraft in position for takeoff (facing into
the wind if flying outdoors). Gradually increase the
throttle to full power, holding a small amount of up
elevator and steering with the rudder. Climb gently
to check trim. Once the trim is adjusted, begin
exploring the flight envelope of the aircraft.
Landing
Always land into the wind. Fly the landing pattern
with a slightly nose high attitude. Use throttle
management to control the decent rate of the
aircraft.
During flare, keep the wings level and the airplane
pointed into the wind. Gently lower the throttle while
pulling back on the elevator to bring the aircraft
down on the main wheels or to belly land without
landing gear.
NOTICE: Always fully lower the throttle when landing
the aircraft to prevent intake of foreign objects,
which can damage the ducted fan and motor.
Failure to lower the throttle stick and trim to the
lowest possible positions during a crash could result
in damage to the ESC in the receiver unit, which
may require replacement.
Over Current Protection (OCP)
The aircraft is equipped with Over Current
Protection. OCP protects the ESC from overheating
and stops the motor when the transmitter throttle is
set too high and the rotor cannot turn. OCP will only
activate when the throttle is positioned just above
1/2 throttle. After the ESC stops the motor, fully
lower the throttle to re-arm the ESC.
Fly in this area
Stand here
600
feet (182.8 m)
Wind

11
EN
Motor Service
Disassembly
CAUTION: DO NOT handle the rotor or
motor while the flight battery is connected.
Personal injury could result.
1. The lower half of the nacelle hatch is secured
to the top half using glue and clear tape.
Carefully cut the clear tape and follow the
seam with a knife to cut the glue and remove
the bottom half of the nacelle.
NOTICE: Removing tape or decals can damage
paint on your aircraft. Avoid pinching or otherwise
damaging any wires when opening or closing the
fuselage.
2. Disconnect the motor from the receiver.
3. Carefully remove the lower half of the nacelle
(A) from the upper half of the nacelle.
4. Remove the 4 screws (B) and fan unit (C)
from the upper nacelle half.
5. Put a small flat blade screwdriver in the motor
mount hole (D) and carefully push the rotor (E)
away from the motor shaft. Rotate the rotor
while prying it away from the motor (F) to avoid
bending the motor shaft.
6. Remove the 4 screws (G) and motor from
the motor mount.
Assembly
Assemble in reverse order, connecting the
top and bottom half of the nacelle with
clear tape and or foam safe CA.
NOTICE: Always install the motor mount so
that the rotor faces the front of the fuselage
and the hole in the unit faces the bottom of
the fuselage.
G
E
A
B
C
D
F

12
EN
Problem Possible Cause Solution
Aircraft will not respond
to throttle but responds
to other controls
Throttle stick and/or throttle trim too high Reset controls with throttle stick and throttle
trim at lowest setting
Throttle channel is reversed Reverse throttle channel on transmitter
Motor disconnected from receiver Open fuselage and make sure motor is
connected to the receiver
Flight battery charge is low Fully recharge flight battery
Extra motor noise or
extra vibration
Damaged rotor or motor Replace damaged parts
Rotor out of balance Balance or replace the rotor
Reduced flight time or
aircraft underpowered
Flight battery charge is low Completely recharge flight battery
Flight battery damaged Replace flight battery and follow flight battery
instructions
Flight conditions may be too cold Make sure battery is warm before use
Battery capacity too low for flight conditions Replace battery or use a larger capacity
battery
LED on receiver flashes
and aircraft will not bind
to transmitter (during
binding)
Transmitter too near aircraft during binding
process
Power off transmitter, move transmitter a
larger distance from aircraft, disconnect and
reconnect flight battery to aircraft and follow
binding instructions
Bind switch or button not held long enough
during bind process
Power off transmitter and repeat bind pro-
cess. Hold transmitter bind button or switch
until receiver is bound
Aircraft or transmitter is too close to large
metal object, wireless source or another
transmitter
Move aircraft and transmitter to another
location and attempt binding again
Troubleshooting Guide
AS3X
Problem Possible Cause Solution
Control surfaces not at
neutral position when
transmitter controls are
at neutral
Control surfaces may not have been
mechanically centered from factory
Center control surfaces mechanically by
adjusting the U-bends on control linkages
Aircraft was moved after the flight battery
was connected and before sensors
initialized
Disconnect and reconnect the flight battery
while keeping the aircraft still for 5 seconds
Model flies
inconsistently from
flight to flight
Aircraft was not kept immobile for 5
seconds after battery was plugged in
Keep the aircraft immobile for 5 seconds after
plugging in the battery
Trims are moved too far from neutral
position
Neutralize trims and mechanically adjust
linkages to center control surfaces
Controls oscillate in
flight, (model rapidly
jumps or moves)
Rotor is unbalanced, causing excessive
vibration
Remove rotor and motor. Check motor shaft
for straightness and replace rotor if damaged
Post Flight Checklist

1. Disconnect the flight battery from the ESC
(Required for safety and battery life).
2. Power OFF the transmitter.
3. Remove the flight battery from the aircraft.
4. Recharge the flight battery.

5. Store the flight battery apart from the aircraft
and monitor the battery charge.
6. Make note of the flight conditions and flight
plan results, planning for future flights.

13
EN
Problem Possible Cause Solution
LED on receiver flashes
rapidly and aircraft will
not respond to transmit-
ter (after binding)
Less than a 5-second wait between first
powering on transmitter and connecting
flight battery to aircraft
Leaving transmitter on, disconnect and
reconnect flight battery to aircraft
Aircraft bound to different model memory
(ModelMatch™radios only)
Select correct model memory on transmitter
and disconnect and reconnect flight battery
to aircraft
Flight battery/transmitter battery charge is
too low Replace/recharge batteries
Transmitter may have been bound to a
different model (or with a different DSM
Protocol)
Select the right transmitter or bind to the
new one
Aircraft or transmitter is too close to large
metal object, wireless source or another
transmitter
Move aircraft and transmitter to another
location and attempt linking again
Control surface does
not move
Control surface, control horn, linkage or
servo damage
Replace or repair damaged parts and adjust
controls
Wire damaged or connections loose Do a check of wires and connections, con-
nect or replace as needed
Flight battery charge is low Fully recharge flight battery
Control linkage does not move freely Make sure control linkage moves freely
Controls reversed Transmitter settings reversed Adjust controls on transmitter appropriately
Motor loses power Damage to motor or power components Do a check of motor and power components
for damage (replace as needed)
Motor power quickly
decreases and in-
creases then motor
loses power
Battery power is down to the point of
receiver/ESC Low Voltage Cutoff (LVC)
Recharge flight battery or replace battery that
is no longer performing
Servo locks or freezes
at full travel
Travel adjust value is set above 100%,
overdriving the servo
Set Travel adjust to 100% or less and/or set
sub-trims to Zero and adjust linkages
mechanically
Troubleshooting Guide (Continued)
Limited Warranty
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original
purchaser that the product purchased (the “Product”)
will be free from defects in materials and workmanship
at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover
(i) cosmetic damage, (ii) damage due to acts of God,
accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or
maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than
a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or
(vi) Product not compliant with applicable technical
regulations, or (vii) use that violates any applicable
laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE,
HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND
ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-
INFRINGEMENT, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE
DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its
option, either (i) service, or (ii) replace, any Product
determined by Horizon to be defective.
Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or
replacement decisions are at the sole discretion of
Horizon. Proof of purchase is required for all warranty
claims. SERVICE OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY.
Problem Possible Cause Solution
Aircraft will not respond
to throttle but responds
to other controls
Throttle stick and/or throttle trim too high Reset controls with throttle stick and throttle
trim at lowest setting
Throttle channel is reversed Reverse throttle channel on transmitter
Motor disconnected from receiver Open fuselage and make sure motor is
connected to the receiver
Flight battery charge is low Fully recharge flight battery
Extra motor noise or
extra vibration
Damaged rotor or motor Replace damaged parts
Rotor out of balance Balance or replace the rotor
Reduced flight time or
aircraft underpowered
Flight battery charge is low Completely recharge flight battery
Flight battery damaged Replace flight battery and follow flight battery
instructions
Flight conditions may be too cold Make sure battery is warm before use
Battery capacity too low for flight conditions Replace battery or use a larger capacity
battery
LED on receiver flashes
and aircraft will not bind
to transmitter (during
binding)
Transmitter too near aircraft during binding
process
Power off transmitter, move transmitter a
larger distance from aircraft, disconnect and
reconnect flight battery to aircraft and follow
binding instructions
Bind switch or button not held long enough
during bind process
Power off transmitter and repeat bind pro-
cess. Hold transmitter bind button or switch
until receiver is bound
Aircraft or transmitter is too close to large
metal object, wireless source or another
transmitter
Move aircraft and transmitter to another
location and attempt binding again
AS3X
Problem Possible Cause Solution
Control surfaces not at
neutral position when
transmitter controls are
at neutral
Control surfaces may not have been
mechanically centered from factory
Center control surfaces mechanically by
adjusting the U-bends on control linkages
Aircraft was moved after the flight battery
was connected and before sensors
initialized
Disconnect and reconnect the flight battery
while keeping the aircraft still for 5 seconds
Model flies
inconsistently from
flight to flight
Aircraft was not kept immobile for 5
seconds after battery was plugged in
Keep the aircraft immobile for 5 seconds after
plugging in the battery
Trims are moved too far from neutral
position
Neutralize trims and mechanically adjust
linkages to center control surfaces
Controls oscillate in
flight, (model rapidly
jumps or moves)
Rotor is unbalanced, causing excessive
vibration
Remove rotor and motor. Check motor shaft
for straightness and replace rotor if damaged

14
EN
Yak 54 3D manual
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF
WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of
Horizon exceed the individual price of the Product
on which liability is asserted. As Horizon has no
control over use, setup, final assembly, modification
or misuse, no liability shall be assumed nor accepted
for any resulting damage or injury. By the act of use,
setup or assembly, the user accepts all resulting
liability. If you as the purchaser or user are not
prepared to accept the liability associated with the
use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to
the place of purchase.
Law
These terms are governed by Illinois law (without
regard to conflict of law principals). This warranty
gives you specific legal rights, and you may also have
other rights which vary from state to state. Horizon
reserves the right to change or modify this warranty
at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase
cannot provide warranty support or service. Once
assembly, setup or use of the Product has been
started, you must contact your local distributor or
Horizon directly. This will enable Horizon to better
answer your questions and service you in the event
that you may need any assistance. For questions
or assistance, please visit our website at www.
horizonhobby.com, submit a Product Support Inquiry,
or call the toll free telephone number referenced in
the Warranty and Service Contact Information section
to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced
and is compliant in the country you live and use the
Product in, please use the Horizon Online Service
Request submission process found on our website
or call Horizon to obtain a Return Merchandise
Authorization (RMA) number. Pack the Product
securely using a shipping carton. Please note that
original boxes may be included, but are not designed
to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon
is not responsible for merchandise until it arrives
and is accepted at our facility. An Online Service
Request is available at http://www.horizonhobby.com/
content/service-center_render-service-center. If you
do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with
instructions for submitting your product for service.
When calling Horizon, you will be asked to provide
your complete name, street address, email address
and phone number where you can be reached during
business hours. When sending product into Horizon,
please include your RMA number, a list of the included
items, and a brief summary of the problem. A copy
of your original sales receipt must be included for
warranty consideration. Be sure your name, address,
and RMA number are clearly written on the outside of
the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If
you have any issue with a LiPo battery, please
contact the appropriate Horizon Product Support
office.
Warranty Requirements
For Warranty consideration, you must include
your original sales receipt verifying the proof-of-
purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced
free of charge. Service or replacement decisions are
at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty,
service will be completed and payment will be
required without notification or estimate of the
expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for
service you are agreeing to payment of the service
without notification. Service estimates are available
upon request. You must include this request with your
item submitted for service. Non-warranty service
estimates will be billed a minimum of ½ hour of labor.
In addition you will be billed for return freight. Horizon
accepts money orders and cashier’s checks, as well
as Visa, MasterCard, American Express, and Discover
cards. By submitting any item to Horizon for service,
you are agreeing to Horizon’s Terms and Conditions
found on our website http://www.horizonhobby.com/
content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership.
If received, a non-compliant Product will not be
serviced. Further, the sender will be responsible
for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice
and at the sender’s expense. Horizon will hold
non-compliant Product for a period of 60 days
from notification, after which it will be discarded.
10/15/15

15
EN
Warranty and Service Contact Information
FCC Information
IC Information
Country of
Purchase Horizon Hobby Phone Number/Email Address Address
United States of
America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.
com/RequestForm/
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.
com
877-504-0233
Sales [e-mail]
888-338-4639
European Union Horizon Technischer Service [email protected] Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH [phone]
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.”
IC ID: 6157A-EFLAS6410NBLT
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: Modifications to this product will void the user’s authority to operate this equipment.
FCC ID: BRWEFLAS6410NBLT

16
EN
Compliance Information for the European Union
EFL UMX A-10 BNF Basic (EFLU3750)
EU Compliance Statement:
Horizon Hobby, LLC hereby declares
that this product is in compliance with the essential
requirements and other relevant provisions of the
RED Directive.
A copy of the EU Declaration of Conformity is
available online at: http://www.horizonhobby.com/
content/support-render-compliance.
Instructions for disposal
of WEEE by users in the
European Union
This product must not be disposed of
with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment
by handing it over to a designated collections point
for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help
to conserve natural resources and ensure that it is
recycled in a manner that protects human health and
the environment. For more information about where you
can drop off your waste equipment for recycling, please
contact your local city office, your household waste
disposal service or where you purchased the product.

59
Part # • Nummer
Numéro • Codice Description Beschreibung Description Descrizione
EFLAS6410NBLT
DSMX 4-Ch AS3X
receiver w/Twin
Brushless ESC
DSMX 4-Kanal AS3X
Empfänger mit
bürstenlosem doppeltem
Geschwindigkeitsregler
Récepteur DSMX
4 voies AS3X avec
double contrôleur
Brushless
Ricevente AS3X a
4 canali DSMX con
doppio ESC brushless
EFLDF180M1 Rotor: Delta-V
180m Rotor: Delta-V 180m Delta-V 180m - Rotor pour turbine Rotore: Delta-V 180m
EFLDF180M2 Delta-V 180m
28mm EDF Unit V2
Delta-V 180m 28mm
EDF-Einheit V2
Delta-V 180m -
Module turbine
28mm EDF V2
Ventola intubata V2
Delta-V 180m 28 mm
EFLM30180MDFC
BL180m Ducted
Fan Motor,
13,500Kv, 100mm
Wire
BL180m Impeller-Motor,
13.500Kv, 100mm
Kabel
Moteur BL180M,
13,500Kv pour
turbine, câble
100mm
Ventola intubata
BL180m con motore,
13.500 Kv, cavo 100
mm
EFLU3701 Main Wing: UMX
A-10 BL
Hauptflügel: UMX A-10
BL
UMX A-10 BL - Aile
principale
Ala principale: UMX
A-10 BL
EFLU3702
Fuselage w/
accessories: UMX
A-10 BL
Rumpf mit Zubehör:
UMX A-10 BL
UMX A-10 BL -
Fuselage avec
accessoires
Fusoliera con
accessori: UMX A-10
BL
EFLU3703
Engine Nacelle
Set w/accesories:
UMX A-10 BL
Motorgondelsatz mit
Zubehör: UMX A-10 BL
UMX A-10 BL -
Nacelle moteur
avec accessoires
Gondola motore con
accessori: UMX A-10
BL
EFLU3704 Tail Set: UMX
A-10 BL
Leitwerksatz: UMX
A-10 BL
UMX A-10 BL -
Empennage
Piani di coda: UMX
A-10 BL
EFLU3705 Landing Gear :
UMX A-10 BL Fahrwerk: UMX A-10 BL UMX A-10 BL - Train d’atterrissage
Carrello d’atterraggio:
UMX A-10 BL
EFLU3706 Hatch/Canopy:
UMX A-10 BL
Abdeckung/Kanzel: UMX
A-10 BL
UMX A-10 BL -
Trappe/Cockpit
Naca pilota/capottina:
UMX A-10 BL
EFLU3707 Decal sheet: UMX
A-10 BL Decalsatz: UMX A-10 BL
UMX A-10 BL
- Planche de
décoration
Decalcomanie: UMX
A-10 BL
EFLU3708 Pushrod set: UMX
A-10 BL
Schubstangensatz: UMX
A-10 BL
UMX A-10 BL -
Tringleries
Aste di commando:
UMX A-10 BL
SPM6836
Replacement
Servo Mechanics:
2.3-Gram 2030L
Ersatz-Servotechnik: 2,3
Gramm 2030L
SA2030L
-Mécanique de
remplacement servo
Meccanica servo
sostitutiva: 2,3 grammi
2030L
SPMSA2030L
2.3-Gram
Performance Linear
Long Throw Servo
2,3 g Performance-
Linearservo mit langem
Ruderweg
Servo linéaire
course longue de
2,3g
Servocomandi lineari
performance a corsa
lunga da 2,3 g
Replacement Parts – Ersatzteile – Pièces de rechange – Ricambi

60
Part # • Nummer
Numéro • Codice Description Beschreibung Description Descrizione
EFLA230 Charger Lead with
JST Female
E-flite Ladekabel m/
JST Buchse
Câble de charge avec
prise JST femelle
Cavo di carica con
femmina JST
DYNC2010CA Prophet Sport Plus
50W AC/DC Charger
Prophet Sport Plus
50W Wechsel-/
Gleichstrom-
Ladegerät
Chargeur Prophet
Sport Plus 50W AC/DC
Caricabatteria
Prophet Sport Plus
50W AC/DC
EFLA111 Li-Po Cell Voltage
Checker
Li-Po-Zelle
Spannungsprüfer
Testeur de tension
batterie Li-Po
Strumento controllo
voltaggio celle LiPo
EFLA700UM Charger Plug Adapter
EFL
Ladegerät
Zwischenstecker EFL
Ultramicro adaptateur
de charge EFL
Adattatore presa
caricabatteria EFL
PKZ1039 Hook and Loop Set (5)
Ultra Micros
Klettbandsatz (5)
Ultra Micros
Set velcro Ultra Micros
(5)
Set fascette fissaggio
(5): Ultra Micros
EFLB4502SJ30 450mAh 2S 7.4V 30C
Li-Po, 18AWG JST
450mAh 3S 7.4V
30C Li-Po, 18AWG
JST Akku
Batterie Li-Po 7.4V 3S
450mA 30C, 18AWG
JST
Batteria Li-
Po450mAh 2S 7.4V
30C, 18AWG JST
EFLB4502SJ50 450mAh 2S 7.4V 50C
Li-Po, 18AWG JST
450mAh 3S 7.4V
50C Li-Po, 18AWG
JST Akku
Batterie Li-Po 7.4V 3S
450mA 50C, 18AWG
JST
Batteria Li-
Po450mAh 2S 7.4V
50C, 18AWG JST
EFLB8002SJ30 800mAh 2S 7.4V 30C
Li-Po, 18AWG JST
800mAh 3S 7.4V
30C Li-Po, 18AWG
JST Akku
Batterie Li-Po 7.4V 3S
800mA 30C, 18AWG
JST
Batteria Li-Po
800mAh 2S 7.4V
30C, 18AWG JST
DXe DSMX 4-Channel
Transmitter
DXe DSMX 4-Kanal-
Sender
Emetteur DXe DSMX
4 voies
DXe DSMX
trasmittente 4 canali
DX6e DSMX
6-Channel Transmitter
DX6e DSMX
6-Kanal Sender
Emetteur DX6e
DSMX 6 voies
DX6e DSMX
trasmittente 6 canali
DX6 G2 DSMX
6-Channel Transmitter
DX6 G2 DSMX
6-Kanal Sender
Emetteur DX6 G2
DSMX 6 voies
DX6 G2 DSMX
trasmittente 6 canali
DX7 G2 DSMX
7-Channel Transmitter
Spektrum DX7 G2
7-Kanal-Sender
Emetteur DX7 G2
DSMX 7 voies
DX7 G2 DSMX
trasmittente 7 canali
DX8 G2 DSMX
8-Channel Transmitter
Spektrum DX8 G2
8-Kanal-Sender
Emetteur DX8 G2
DSMX 8 voies
DX8 G2 DSMX
trasmittente 8 canali
DX9 DSMX
9-Channel Transmitter
Spektrum DX9
9-Kanal-Sender
Emetteur DX9 DSMX
9 voies
DX9 DSMX
trasmittente 9 canali
DX18 DSMX
Transmitter
Spektrum DX18 nur
Sender
Emetteur DX18 DSMX
8 voies
DX18 DSMX Solo
trasmittente
DX20 DSMX
Transmitter
Spektrum DX20 nur
Sender
Emetteur DX20 DSMX
8 voies
DX20 DSMX Solo
trasmittente
Optional Parts and Accessories
Optionale Bauteile und Zubehörteile
Pièces optionnelles et accessoires
Parti opzionali e accessori

© 2017 Horizon Hobby, LLC.
E-flite, AS3X, UMX, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, Celectra
and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha
Corporation of Japan.
All other trademarks, service marks and logos are property of their respective owners.
US 7,898,130. US D578,146. PRC ZL 200720069025. PRC ZL 2007001249, US 8,672,726.
Other patents pending.
www.e-fliterc.com Updated 10/17 50080.2EFLU3750