Horstmann ThermoPlus AS2-RF User manual

Page 1Page 16
TTHHEERRMMOOPPLLUUSSAASS22--RRFF
UUSSEERRIINNSSTTRRUUCCTTIIOONNSS
IINNTTRROODDUUCCTTIIOONN
LEAFLET No P83020
ISSUE 1
Horstmann Controls Limited
Bristol
BS4 1UP
Email: [email protected]
Website: www.horstmann.co.uk
The Horstmann ThermoPlus AS2-RF is a wireless room thermostat that has been designed
to make its operation very simple for the householder.
The built in automatic clock means it will not need setting or adjusting for BST and GMT
time changes.
The ThermoPlus will provide a Warm temperature setting at times pre-set by your installer
and day-to-day user adjustments are carried out using just three buttons.
The ThermoPlus AS2-RF is supplied in two parts. The receiver which is hard wired to the
combi or conventional system boiler and the AS2-RF thermostat which can be used in any
normal domestic environment within a typical 30 metre range without the need for any
costly or disruptive wiring.
TThheeHHoorrssttmmaannnnTThheerrmmooPPlluussAASS22--RRFF--PPrrooggrraammmmaabblleeRRoooommTThheerrmmoossttaattwwiitthh
wwiirreelleessssccoommmmuunniiccaattiioonntteecchhnnoollooggyy..

Page 15
TTHHEERRMMOOPPLLUUSSAASS22--RRFF--PPRROODDUUCCTTOOVVEERRVVIIEEWW
11
DDEE
CC
22
3344FF
BBAA
TThheerrmmooPPlluussAASS22--RRFFTTrraannssmmiitttteerr
LLCCDDDDIISSPPLLAAYYFFEEAATTUURREESS --A fully graphical
back-lit installer and user display.
LLEEDDIINNDDIICCAATTOORR --Red and Blue indicators
show if you are in a ‘Warm’ or ‘Cool’ period.
PPRREESSEETTPPRROOGGRRAAMMMMEESS --Programming is
made simple and a one touch override
facility makes temporary changes simple to
use.
AAUUTTOOMMAATTIICCCCLLOOCCKK --A factory set clock
which automatically adjusts between
winter (GMT) and summer (BST) time.
AA--PPlluuss‘‘++’’BBuuttttoonn
BB--LLEEDDIInnddiiccaattoorrlliigghhttss
CC--IInnssttaalllleerrDDiissppllaayy
DD--‘‘WWaarrmm//CCooooll’’BBuuttttoonn
EE--MMiinnuuss‘‘--’’BBuuttttoonn
FF--SSttaannddbbyy//TTiimmee//SSeettBBuuttttoonn
GG--IInnccrreeaassee//DDeeccrreeaasseeBBuuttttoonnss
HH--PPrroogg//EExxiittBBuuttttoonn
What is a room thermostat?
... an explanation for householders
A room thermostat simply switches the heating system on
and off as necessary. It works by sensing the air
temperature, switching on the heating when the air
temperature falls below the thermostat setting, and
switching it off once this set temperature has been
reached.
Turning a room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up depends on the design of the
heating system, for example, the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a room thermostat to a lower
setting will result in the room being controlled at a lower temperature, and saves energy.
The heating system will not work if a time switch or programmer has switched it off.
The way to set and use your room thermostat is to find the lowest temperature setting that you are
comfortable with, and then leave it alone to do its job. The best way to do this is to set the room
thermostat to a low temperature - say 18oC - and then turn it up by one degree each day until you are
comfortable with the temperature. You won't have to adjust the thermostat further. Any adjustment
above this setting will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one room thermostat to
control the whole house. But you can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don't have TRVs, you should choose
a temperature that is reasonable for the whole house. If you do have TRVs, you can choose a slightly
higher setting to make sure that even the coldest room is comfortable, then prevent any overheating
in other rooms by adjusting the TRVs.
Room thermostats need a free flow of air to sense the temperature, so they must not be covered by
curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the
thermostat from working properly.
The above explanation has been kindly provided by the association of heating controls
manufacturers as a guide to encouraging the correct and efficient use of heating controls.
The AS2-RF thermostat kit is made up of two parts:
1 x ASR-RF Receiver
1 x AS2-RF Transmitter
Both parts have been designed to be easily installed and offer maximum flexibility. No hard
wiring is required between the transmitter and the receiver. The receiver unit is hard wired to
the boiler and should be sited close to the existing wiring. The AS2-RF can then be positioned
up to 30 metres away -
Range will vary depending upon the composition, density and number
of walls between the AS2-RF transmitter and the receiver.
TThheerrmmooPPlluussAASSRR--RRFFRReecceeiivveerr
LLEEDDIINNDDIICCAATTOORR- The tri-colour LED gives the
status indication to the user and installer.
EEAASSYYTTOOUUSSEEPPAAIIRRIINNGGAANNDDOOVVEERRRRIIDDEE
BBUUTTTTOONNSS- Simple to identify colour coded
buttons allow you to connect the
transmitter and receiver. They also allow
override of the boiler without the
transmitter. (see section 3)
11--SSttaattuussIInnddiiccaattoorrLLEEDD
22--AASS22--RRFFAAdddd//RReemmoovveeBBuuttttoonnss
33--BBooiilleerr‘‘OOffff’’OOvveerrrriiddee****((RReedd))
44--BBooiilleerr‘‘OOnn’’OOvveerrrriiddee****((GGrreeeenn))
**The override facility will only operate
when a flashing amber LED is showing. This
indicates no signal from the AS2-RF
transmitter is being received, the position
and battery level should be checked.
Page 2
For more information on Z Wave technology
please visit;
wwwwww..zzeenn--ssyyss..ccoomm
AASSRR--RRFFRREECCEEIIVVEERRAASS22--RRFFTTRRAANNSSMMIITTTTEERR
GGHH

Page 14
SSEECCTTIIOONN11--UUNNDDEERRSSTTAANNDDIINNGGTTHHEEAASS22--RRFF
IINNDDEEXX
IINNTTRROODDUUCCTTIIOONNPPAAGGEE11
PPRROODDUUCCTTOOVVEERRVVIIEEWWPPAAGGEE22
SSEECCTTIIOONN11--UUNNDDEERRSSTTAANNDDIINNGGTTHHEEAASS22--RRFF;;
IINNDDIICCAATTIINNGGLLIIGGHHTTSSAANNDDBBAACCKK--LLIITTDDIISSPPLLAAYYPPAAGGEE33
SSTTAANNDDBBYY//FFRROOSSTTPPRROOTTEECCTTIIOONNPPAAGGEE33
PPOOWWEERRDDOOWWNNMMOODDEEPPAAGGEE33
SSEECCTTIIOONN22--SSEETTTTIINNGGSSAANNDDAADDJJUUSSTTMMEENNTT
WWAARRMMAANNDDCCOOOOLLTTEEMMPPEERRAATTUURREEAADDJJUUSSTTMMEENNTTPPAAGGEE44
AASS22--RRFFPPRROOGGRRAAMMMMIINNGGMMOODDEEPPAAGGEE55
AASS22--RRFFTTIIMMEEAALLTTEERRAATTIIOONNPPAAGGEE55
SSEETTTTIINNGGHHEEAATTIINNGGPPRROOFFIILLEESSPPAAGGEE66
HHEEAATTIINNGGPPRROOFFIILLEESS((11--33))PPAAGGEE77
HHEEAATTIINNGGPPRROOFFIILLEESS((44--55))PPAAGGEE88
PPRROOFFIILLEE66--UUSSEERRDDEEFFIINNAABBLLEEPPAAGGEE99
SSEECCTTIIOONN33--UUNNDDEERRSSTTAANNDDIINNGGTTHHEERREECCEEIIVVEERR;;
RRFFTTEECCHHNNOOLLOOGGYYPPAAGGEE1100
SSTTAATTUUSSIINNDDIICCAATTOORRLLEEDDPPAAGGEE1100
FFAAIILLSSAAFFEEMMOODDEEPPAAGGEE1111
SSEECCTTIIOONN44--GGEENNEERRAALLIINNFFOORRMMAATTIIOONN
RREESSEETTTTIINNGGTTHHEEAASS22--RRFFPPAAGGEE1122
OOPPEERRAATTIINNGGMMOODDEESSPPAAGGEE1122
BBAATTTTEERRYYRREEPPLLAACCEEMMEENNTTPPAAGGEE1133
SSEERRVVIICCEEAANNDDRREEPPAAIIRRPPAAGGEE1133
WWHHAATTIISSAATTHHEERRMMOOSSTTAATT??PPAAGGEE1155
The ThermoPlus AS2-RF is battery powered and is intended for applications where no mains
supply is readily available to operate the unit. To conserve battery life, the indicator lights and
the display backlighting will go out after 8 seconds. The LCD target temperature display will
remain on, but not back-lit, at all times.
The LED indicators will illuminate whenever the ‘+/-’ or ‘Warm/Cool’ buttons are pressed. The
back-lit display will also operate whenever any of the buttons located under the flap are
pressed. ‘
The LED indicators will convey the heating status by adjusting the number and colour of the
LED’s displayed;
- ‘Warm’ is shown by two red lights - Adjustment to this temperature of 1oC can be made by
pressing the ‘+’ button, to a maximum increase of 2oC, and the ‘-’ button to a maximum
decrease of 2oC
- ‘Cool’ is shown by a single blue light - The '+' and '-' buttons have no effect on the lower
temperature setting
PLEASE NOTE; The centre button marked 'Warm/Cool' allows you to toggle between the Warm
and Cool settings.
IINNDDIICCAATTIINNGGLLIIGGHHTTSSAANNDDBBAACCKK--LLIITTDDIISSPPLLAAYY
SSTTAANNDDBBYY//FFRROOSSTTPPRROOTTEECCTTIIOONN
The blue button situated under the flap will initiate the
frost protection mode when pressed, the word
’STANDBY’ will appear on the display, the thermostat
has been pre-programmed with a frost protection
temperature level of 7oC, this can be adjusted by using
the up and down arrow buttons. To resume normal
operation press the blue button to cancel the frost
protection.
PRESS FOR STANDBY / FROST PROTECTION
PPOOWWEERRDDOOWWNNMMOODDEE
During normal operation the AS2-RF will go into Power Down Mode, this is to maximise the life
of the 3 x AA batteries fitted. Normal operation will continue during this mode, and the heating
will be unaffected. The result of the Power Down Mode will mean that the LED indicators will
not be displayed and LCD will not be illuminated, although the ‘Warm’ or ‘Cool’ temperature will
be displayed.
To ‘wake up’ the AS2-RF press the ‘Warm/Cool’ button for 5 seconds, this will then illuminate
both the LED and LCD displays for a period. Any adjustment can then be made, the Power Down
Mode will commence again approximately 8 seconds after the last button press.
Page 3

Page 13
SSEERRVVIICCEEAANNDDRREEPPAAIIRR
The ThermoPlus AS2-RF is NOT user serviceable. Please do not dismantle the unit.
In the event of a fault developing please refer to the RESETTING THE THERMOSTAT section of this
user guide. If this fails to resolve the problem please contact a local heating engineer or a
qualified electrician.
NNOOTTEESS
WWAARRMMAANNDDCCOOOOLLTTEEMMPPEERRAATTUURREEAADDJJUUSSTTMMEENNTT((PPEERRMMAANNEENNTT))
To change a target temperature it is first necessary to press the
the centre button to bring up the ‘Warm’ or ‘Cool’ setting
(Indicated by the red or blue LED indicators).
Use the up/down keys under the flap to increase or decrease to
the desired temperature setting
PLEASE NOTE - it is not possible to set the ‘Warm’ setting to
below that of the ‘Cool’ setting or vice versa.
Once a new temperature has been set in either the Warm or Cool
setting the AS2-RF will continue to use this setting until the next
manual adjustment.
The ThermoPlus has two preset temperature levels, these are known as;
- ‘Warm’, higher level temperature(21oC)
- ‘Cool’, lower or set back temperature (15oC).
The preset temperatures have been selected to give a comfortable, safe, yet efficient
temperature level in the home.
In certain installations it may be necessary to adjust either the ‘Warm’ or ‘Cool’ temperatures
to meet the specific needs of the user. This can be achieved by following the simple steps
below;
SSEECCTTIIOONN22--SSEETTTTIINNGGSSAANNDDAADDJJUUSSTTMMEENNTT
The temperature settings on the AS2-RF will have been set by
the installer to match your lifestyle, however if any temporary
increase or decrease to the ‘Warm’ setting is required you can
press the ‘+’ or ‘-’ buttons. The temperature change will be
indicated by both the LED and LCD user displays
PLEASE NOTE;
- This is a temporary change and will revert back to the normal
setting at the next programmed ‘Warm/Cool’ change.
- This does not indicate a permanent change in the ‘Warm’
settings.
- During an override the word ‘Warm’ will disappear from the
LCD display indicating an override is active.
- The ‘+’ and ‘-’ buttons have no effect on the ‘Cool’ setting
WWAARRMMTTEEMMPPEERRAATTUURREEAADDJJUUSSTTMMEENNTT((TTEEMMPPOORRAARRYY))
Page 4
Warm/Cool Up/Down

SSEECCTTIIOONN44--GGEENNEERRAALLIINNFFOORRMMAATTIIOONN
OOPPEERRAATTIINNGGMMOODDEESS
During normal operation the receiver will indicate the boiler status through the colour of its LED,
please refer to the receiver STATS INDICATOR LED section of this guide.
The AS2-RF also uses a combination of LED and LCD displays to assist the user to gain maximum
benefit from the thermostat, during normal operating periods, where no user intervention has
occurred, the AS2-RF will power down to maximise battery life, to ‘wake’ the AS2-RF press the
Warm/Cool for 5 seconds, the displays, both LED and LCD, will now illuminate and will stay lit
for a period of 8 seconds after the last button press.
- On the ThermoPlus AS2-RF press the ‘UP’ and
‘DOWN’ arrow buttons together:
- Then release the buttons and the thermostat will
return to preset factory settings.
RREESSEETTTTIINNGGTTHHEETTHHEERRMMOOPPLLUUSSAASS22--RRFF
TO RESET PRESS
PLEASE NOTE; Using this procedure will restore the AS2-RF to the original factory settings, the
time of day will also revert to 1/1/06, details of how to adjust the time are contained within
the user guide.
Electronic equipment can in some circumstances be affected by electrical interference. If the
display becomes frozen or scrambled; or if you wish to revert back to the default settings
please use the following procedure.
RREESSEETTTTIINNGGTTHHEEAASS22--RRFFTTRRAANNSSMMIITTTTEERR
Page 12
BBAATTTTEERRYYRREEPPLLAACCEEMMEENNTT
The ThermoPlus AS2-RF uses 3 x AA(LR6) batteries. The batteries supplied with the unit should
last for approximately two years. When the batteries are nearing the end of their life a ‘LOW
BAt’ message will flash on the display.
To change the batteries it is necessary to remove the AS2-RF from the wall, to achieve this first
press the RELEASE BUTTONS located under the unit and pull the AS2-RF away from the mounting
plate by gently pulling up.
Remove the old batteries and replace them with three new AA size alkaline batteries, ensure
they are fitted correctly as shown by the marking positioned between the battery terminals.
Once batteries have been fitted, replace the AS2-RF to the mounting plate, ensuring that the
two guide lugs are fitted into the corresponding slots in the top of the mounting plate. Now
push the AS2-RF until the release button clicks into place.
WARNING : You must always ensure that the AS2-RF is always running on 3 x AA batteries, when
the battery low message is indicated it is impotant that they are exchanged as soon as possible.
This is to preserve the secondary internal reserve battery which is non-replaceble.
The ThermoPlus thermostat has been pre-set with the current time and date during
manufacture. No alteration should be required to the time and date, however if any
modification is required please refer to the flowchart below.
AASS22--RRFFTTIIMMEEAALLTTEERRAATTIIOONN
Press
Page 5
AASS22--RRFFPPRROOGGRRAAMMMMIINNGGMMOODDEE
The ThermoPlus AS2-RF has been designed to operate with as little as possible adjustment by
the user.
However, should any programming adjustments be required then lift the flap and press the two
outer buttons simultaneously. This will allow you to enter the programming mode to check and
adjust any of the following
;
--CChheecckktthheeccuurrrreennttttiimmee//ddaattee//yyeeaarr
--CChheecckktthheeccuurrrreennttpprrooffiillee
--SSeettaanneewwpprree--sseettoorruusseerrddeeffiinneeddpprrooffiillee
PPLLEEAASSEENNOOTTEE;;Upon completion of any changes/reviews
made, please ensure that you exit the programming
mode using the same two buttons.

SSEETTTTIINNGGHHEEAATTIINNGGPPRROOFFIILLEESS
The ThermoPlus contains a selection of five pre-set and one user definable profile options, one
of these may have been set by the Installer. Care should be taken to ensure a profile is selected
that suits the lifestyle of the user concerned.
The flow chart below is designed to easily guide you through the process of setting the required
profile.
Profiles one to five are detailed on pages 7 and 8.
If none of the pre-set profiles meet your requirements it is possible to set a user defined profile,
full details are given on page 9.
PPrrooffiilleessoonneettooffiivveehhaavveeffiixxeeddpprrooggrraammmmeess,,tthheeyyccaannbbeerreevviieewweeddbbyy
pprreessssiinnggtthheesseettbbuuttttoonnoonncceetthheesseelleeccttiioonnpprroocceessssddeettaaiilleeddaabboovveehhaass
bbeeeennccoommpplleetteedd..TToosseettaaccuussttoommpprrooffiilleepplleeaasseerreeffeerrttootthheeiinnssttrruuccttiioonnss
oonnppaaggee99..
Page 6
RREECCEEIIVVEERRFFAAIILLSSAAFFEEMMOODDEE
Should your receiver enter the Fail Safe Mode this will be conveyed by the LED indicator going
solid amber. This will only happen if the receiver has not received a signal from the AS2-RF for
more than 60 minutes. Some basic instructions are detailed in the section above and on the
inside of the receiver flap for the emergency use of the relay/heating during this mode.
To resume normal operation please use the following procedures;
1. Press the ‘warm/cool’ button on the front of the AS2-RF for 5 seconds, or until the display
illuminates, then press again to send a signal to the receiver receiver, if successful this will be
indicated by the LED on the receiver changing from amber to either red or green.
or
2. Check and replace, if necessary, the 3 x AA batteries in the AS2-RF transmitter, then follow
process (1) above.
3. If process (1) and (2) fail to regain normal operation then please consult your heating or
service engineer for further assistance.
AASS22--RRFFNNOOSSIIGGNNAALLIINNDDIICCAATTOORR
CCOOMMMMUUNNIICCAATTIIOONNFFAAIILLSSAAFFEEMMOODDEESS
Should your AS2-RF enter the Fail Safe Mode this will be conveyed by the LCD display showing
‘No Sig’ every 3 seconds. This indicates that the AS2-RF has not received a signal to confirm the
last ‘Warm/Cool’ change from the receiver.
To resume normal operation please use the following procedures;
1. Press the ‘Warm/Cool’ button on the front of the AS2-RF for 5 second, or until the display
illuminates, then press again to send a signal to the receiver receiver, if successful this will make
the ‘No sig’ flag disappear
or
2. Check the receiver receiver, if the LED is nnoottilluminated this indicates a power interruption
or disconnection. Check the 3A fused spur supply, if the LED then illuminates on the receiver
then press any button on the AS2-RF to reconnect.
if checking the 3A spur supply fails to illuminate the LED then the assistance of an electrician or
service engineer should be sought.
Page 11

Page 10
HHEEAATTIINNGGPPRROOFFIILLEESS
PPRROOFFIILLEEOONNEE--DDEEFFAAUULLTTSSTTAARRTTSSTTAATTUUSS
EVERY DAY 0066::0000WWAARRMM
22:00 COOL
PPRROOFFIILLEETTWWOOSSTTAARRTTSSTTAATTUUSS
EVERY DAY 0066::0000WWAARRMM
08:00 COOL
1177::0000WWAARRMM
22:30 COOL
PPRROOFFIILLEETTHHRREEEESSTTAARRTTSSTTAATTUUSS
EVERY DAY 0066::0000WWAARRMM
08:00 COOL
1111::3300WWAARRMM
13:30 COOL
1177::0000WWAARRMM
22:30 COOL
Time
Profile
Warm
Cool
5
6
7
8
1
2
3
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
00
TIME PROFILE
TEMPERATURE P ROFILE
Time
Profile
Warm
Cool
22
23
TEMPERATURE P ROFILE
18
19
20
21
14
15
16
17
TIME PROFILE
1
2
3
4
5
6
7
00
8
9
10
11
12
13
Time
Profile
Warm
Cool
00
TEMPERATURE P ROFILE
18
19
20
21
14
15
TIME PROFILE
1
2
3
4
5
6
7
22
23
8
9
10
11
12
13
16
17
PPRROOFFIILLEE
1
PPRROOFFIILLEE
2
PPRROOFFIILLEE
3
Page 7
RREECCEEIIVVEERRSSTTAATTUUSSIINNDDIICCAATTOORR((LLEEDD))LLIIGGHHTT
The Tri-coloured LED on the receiver allows both the installer and the end user to understand
the status of communication between the receiver and the AS2-RF.
The LED has six different indications, these are;
IINNSSTTAALLLLAATTIIOONNMMOODDEE;;PLEASE NOTE; These will not be visible during normal user operation,
users should not attempt to re-commission an existing installation, please consult your service
engineer for assistance.
FFllaasshhiinnggRReedd- No network connection, please refer to
‘COMMISSIONING INSTRUCTIONS’ section of the
installation guide.
FFllaasshhiinnggGGrreeeenn- Indicates a successful network connection.
NNOORRMMAALLOOPPEERRAATTIIOONN;;The following LED indications should be present during normal
operation;
SSoolliiddRReedd- Heating off
SSoolliiddGGrreeeenn- Heating on
FFAAIILLSSAAFFEEMMOODDEEIf, during normal operation, the RF signal is lost for more than 60
minutes then the receiver will switch to Fail Safe Mode(off). During Fail Safe Mode the receiver
relay/heating will be switched off and can be controlled by using the emergency red(off) and
green(on) buttons located below the flap on the receiver if required, further details are given
in the following sections. When the emergency buttons are used the LED will operate in the
following way;
SSoolliiddAAmmbbeerr- Heating off - indicating no message from AS2-RF for
60 minutes -
FFllaasshhiinnggAAmmbbeerr- Heating on - Green override button activated
SSEECCTTIIOONN33--UUNNDDEERRSSTTAANNDDIINNGGTTHHEERREECCEEIIVVEERR
RRFFTTEECCHHNNOOLLOOGGYY
The AS2-RF thermostat uses radio frequency technology to
communicate wirelessly between the receiver and
transmitter. This makes the AS2-RF ideal for fitting in either
new or existing systems where additonal wiring cannot be
used for either practical or cosmetic reasons. The receiver and
AS2-RF use Z-wave technology to communicate, this means it
can be used as a stand alone item or added to an existing Z-
wave installation.
PLEASE NOTE; The red and green override buttons on the receiver will only operate in fail safe
mode. In normal operation pressing these buttons will have no effect.
The ThermoPlus has six heating profiles, five are fixed and one is adjustable. Profile ‘OONNEE’ has
been set as the default and is detailed below. During installation a heating profile should have
been set to best match your requirements, illustrations of the pre-set profiles are shown
below.
24 Hour
24 Hour
24 Hour

PPRROOFFIILLEEFFOOUURRSSTTAARRTTSSTTAATTUUSSSSTTAARRTTSSTTAATTUUSS
MON - FRI 0066::0000WWAARRMMSAT/SUN 0077::0000WWAARRMM
08:00 COOL 22:00 COOL
1111::3300WWAARRMM
13:30 COOL
1177::0000WWAARRMM
22:30 COOL
PPRROOFFIILLEEFFIIVVEESSTTAARRTTSSTTAATTUUSSSSTTAARRTTSSTTAATTUUSS
MON - FRI 0066::0000WWAARRMMSAT/SUN 0077::0000WWAARRMM
08:00 COOL 22:00 COOL
1177::0000WWAARRMM
22:30 COOL
Time
Profile
MON - FRI
SAT / SUN
MON - FRI
Warm
Cool
SAT / SUN
Warm
Cool
TEMPERATURE P ROFILE
22
23
00
18
19
20
21
14
15
16
17
10
11
12
13
6
7
8
9
2
3
4
5
TIME PROFILE
1
Time
Profile
MON - FRI
SAT / SUN
MON - FRI
Warm
Cool
SAT / SUN
Warm
Cool
TIME PROFILE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
00
TEMPERATURE P ROFILE
Profiles one to five have fixed periods, no alteration to the Warm/Cool times can be made,
if it is necessary to make any alterations then profile six must be used. Profile six will allow you
to set up a profile to your exact requirements. Please refer to the flowchart opposite
PPRROOFFIILLEE
4
PPRROOFFIILLEE
5
55//22DDAAYY
55//22DDAAYY
Page 8
PPRROOFFIILLEESSIIXX
UUSSEERRDDEEFFIINNAABBLLEE--77DDAAYYPPRROOGGRRAAMMMMIINNGG
Profile six will allow you to set up a profile to your exact requirements. By using the flow
chart below you can adjust the Warm/Cool timing periods on each day of the week.
CCOOPPYYFFEEAATTUURREE
TThheeccooppyyffeeaattuurreeccaannbbee
uusseeddttooaappppllyycchhaannggeess
mmaaddeeffrroommoonneeddaayyss
pprrooggrraammmmiinnggttootthheenneexxtt..
TThhiissiissaacchhiieevveeddbbyypprreessssiinngg
tthheeddoowwnnaarrrroowwbbuuttttoonn
wwhheenn‘‘SSEETT’’iissddiissppllaayyeeddoonn
tthheessccrreeeenn..
‘‘SSEETT’’iissddiissppllaayyeeddaafftteerrtthhee
llaassttccoooollppeerriiooddiissccoonnffiirrmmeedd
oonneeaacchhddaayy..
PPRROOFFIILLEE
6
77DDAAYY
Page 9