Somfy Chronis smoove series User manual

www.somfy.com

Interactive operating instructions

Ref. 5129502A

Chronis Smoove UNO

Chronis Smoove UNO S

Chronis Smoove IB+

Soliris Smoove UNO

Soliris Smoove IB+

IB+

Chronis

& Soliris Smoove

2/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

Thank you for choosing this Somfy product.

Simply elegant

Somfy is proud to present you two new ranges of touch-sensitive buttons, wired, automatic controls

with timeless and sleek design.

Chronis Smoove Uno and IB+ range:

Time is controlled thanks to these programmable clocks for automatic opening/closing of motorized

equipment (roller shutters, external venetian blinds, external blinds). These controls can be used in

3 ways: in manual mode, in automatic mode, or in simulated presence mode.

The Chronis Smoove UNO S and Chronis Smoove IB+ can be associated with an io homecontrol® sun

sensor.

Soliris Smoove Uno and IB+ range:

Climate is controlled thanks to an automated system for opening/closing the motorized equipment

(patio awnings, interior blinds, roller shutters, external venetian blinds, external blinds) depending on

sunlight or outdoor weather conditions (wind/rain). These controls can be used in 3 ways: in manual

mode, in automatic mode, or in simulated presence mode.

The Soliris Smoove UNO and Soliris Smoove IB+ can be associated with an io homecontrol® sun

sensor and also wired sensors (sun/light, rain, wind sensors).

The UNO versions are dedicated to control one motor.

The IB+ versions are dedicated to IB+ motor controller devices (1 to 3 channels).

Interactive operating instructions

This full manual describes the operating instructions to make the best use of the 5 products of the

new Chronis & Soliris Smoove ranges:

• Chronis Smoove UNO

• Chronis Smoove UNO S

• Chronis Smoove IB+

• Soliris Smoove UNO

• Soliris Smoove IB+

To ﬁnd the common or speciﬁc functions of each product, consult the following table Functions of the

5 products : available functions of each product are indicated by a small icon.

The table of Contents presents all instructions for the 5 products. When a chapter describes a

function that does not apply to all products, the concerned products are indicated in the heading of

the chapter.

This manual is interactive:

• Click on each title or page number in the table of Contents to access it directly.

• Click on [ Back to Contents ] at the bottom of each page to return to table of Contents.

WELCOME PAGE

3/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

Functions of the 5 products

Features

Chronis

Smoove

UNO

Chronis

Smoove

UNO S

Chronis

Smoove

IB +

Soliris

Smoove

UNO

Soliris

Smoove

IB +

TimerSnow

Rain Moon / night

TemperatureCloud

Sun / day Wind Heating

Light

Audi/Video Entry door

security Remote control

Wall mounted control

Domotique

Air conditioning

Alarm Intercom

Fire

Week program

+ pre-programmed days

Backlight

1 channel

1 to 3 channels

2 orders/day

4 orders/day

Presence simulation

Automatic Summer/Winter time

Sunset (in the control)

Sunrise (in the control)

Auto from

Optional settings

and copy/paste with a tool

TimerSnow

Rain Moon / night

TemperatureCloud

Sun / day Wind Heating

Light

Audi/Video Entry door

security Remote control

Wall mounted control

Domotique

Air conditioning

Alarm Intercom

Fire

Façade wireless io sun sensor :

sun protection, sunrise & sunset

Sun sensor (wired) :

sun protection, sunrise & sunset

TimerSnow

Rain Moon / night

TemperatureCloud

Sun / day Wind Heating

Light

Audi/Video Entry door

security Remote control

Wall mounted control

Domotique

Air conditioning

Alarm Intercom

Fire

Rain sensor (wired only)

TimerSnow

Rain Moon / night

TemperatureCloud

Sun / day Wind Heating

Light

Audi/Video Entry door

security Remote control

Wall mounted control

Domotique

Air conditioning

Alarm Intercom

Fire

Wind sensor (wired only)

PRODUCTS & FUNCTIONS

4/40

Chronis & Soliris Smoove

Interactive operating instructions

CONTENTS

[ Interactive instructions ]

You can click on each title to access it directly.

1. DESCRIPTION OF FUNCTIONS 5

1.1. UNO Versions - for controlling a 230V AC single motor 5

1.2. IB+ Versions - for controlling Smoove devices with IB+ input 5

2. SOFT KEY FUNCTIONS 6

3. DISPLAY 7

4. STARTING UP 8

4.1. Language 8

4.2. Time and Date 8

4.3. Type of End products 8

4.4. Runtime setup 9

4.5. Sun/light Sensor 10

4.6. Wind Sensor (Soliris versions) 11

4.7. Rain Sensor (Soliris versions) 12

4.8. End of initial settings 12

5. MANUAL MOVE COMMAND 13

6. QUICK MENU 14

6.1. Automatic 14

6.2. Auto from 14

6.3. Holiday mode 15

6.4. Manual 15

6.5. Settings 15

7. SETTINGS MENU 16

7.1. Program Timer / Cycle Times 16

7.2. Sun Function 21

7.3. Wind Function (Soliris versions) 26

7.4. Rain Function (Soliris versions) 28

7.5. Conﬁguration in the "Normal" operating mode 30

7.6. Conﬁguration in Professional Operating Mode 32

7.7. Additional functions in Expert Mode 37

8. TECHNICAL DATA 39

5/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

1. DESCRIPTION OF FUNCTIONS

1.1. UNO Versions - for controlling a 230V AC single motor

Chronis Smoove UNO

Automatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Up to two

time-dependent control commands per day. Settings for the device over a backlit menu display.

Chronis Smoove UNO S

Automatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Sun- and

sunset-dependent control. Up to 4 time-dependent control commands per day. Settings for the device

over a backlit menu display.

Soliris Smoove UNO

Automatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Weather-

dependent control (wind, rain, sun/light, and sunset). Up to 4 time-dependent control commands per

day. Settings for the device over a backlit menu display.

1.2. IB+ Versions - for controlling Smoove devices with IB+ input

Important: The settings on Chronis / Soliris Smoove IB+ Smoove devices must be matched with the

installed Smoove devices. Current Smoove devices are ﬁtted with an IB+ Bus input. Previous versions

have an IB Bus input. With systems that have IB, as well as IB+ Smoove devices, the IB+ operating

mode must be selected in all cases.

Chronis Smoove IB+

Automatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Sun- and

sunset-dependent control. Up to 4 time-dependent control commands per day. Using a Chronis

Smoove IB+ device, up to 100 IB/IB+ motor controller devices can be controlled. Settings for the

device over a backlit menu.

Warning: All connected end products must be of the same type (e.g. all Venetian blinds).

Soliris Smoove IB+

Automatic and manual control of multiple motors for roller shutters, Venetian blinds or awnings.

Weather-dependent control (wind, rain, sun/light, and sunset). Up to 4 time-dependent control

commands per day. Using a Soliris Smoove IB+ device, up to 100 IB/IB+ Smoove devices can be

controlled. Settings for the device over a backlit menu display.

Warning: All connected end products must be of the same type (e.g. all Venetian blinds).

6/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

2. SOFT KEY FUNCTIONS

- In the main display: shows the sensors activated under the line for 5 seconds

- In the settings: back to a higher menu

- In the Quick Menu: back to main display

- Moves end products upwards or downwards

- For setting the function: value change, operating the cursor

- For navigating between menus

- Stop function when the end product is moving

- Go to "my" Position when the end product is stopped

- Setting of "my" Position

- In the main display: with a short press, go to "Quick Menu"

- In the main display: with a long press (> 2 secs.), go to "Conﬁguration menu"

- In the settings: conﬁrm a setting / value

7/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

3. DISPLAY

The display is ﬁtted with a lit background. In the main menu, the display shows the time of day and,

depending on the type of operation (see Chapter "Quick Menu"), the activated function (picture 1), as

well as when a function is currently active (picture 2).

Stand-by-Mode:

Aer 3 minutes without touching, the lighting on the display switches oﬀ. By touching a so key, the

lighting is activated again without setting oﬀ a command.

Main menu with activated (switched on) sensor functions (only for Chronis

Smoove Uno S and Soliris).

Main display, when an automatic function, e.g. the sun function, is

activated.

Sensor(s) enabled

08:23

POS.

8/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

Important: When installing, check whether the adapter for the logic module ﬁts (the backside of both

parts is labeled). If the wrong adapter is used unintentionally, the following message is displayed:

"WARNING - not compatible". The logic module or adapter hereby will not be damaged.

If the device has not been put into operation yet, you are automatically guided through the basic

settings.

If the device has already been put into operation, go directly to the next chapter "Manual move

command".

The basic settings are to be followed step by step:

- To go to the next sep, the conﬁguration must be conﬁrmed.

- Use the so key to go back to the previous step.

4.1. Language

1. Choose the display language.

2. Conﬁrm your selection.

4.2. Time and Date

Time

1. Set the time / hours between 00 and 23 hrs and conﬁrm.

2. Set the minutes and conﬁrm.

Tip: Press longer on the so key to change the values quicker.

Date

1. Set the day and conﬁrm.

2. Repeat to set the month and year.

Tip: Press longer on the so key to change the values quicker.

4.3. Type of End products

1. Choose the connected end product between roller shutters, awnings

and Venetian blinds.

2. Conﬁrm your selection.

4. STARTING UP

Language

English

German

10:41

14 .12.15

Date

Producttyp setup

Roller shutter

Venetian blinds

9/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

4. STARTING UP

4.4. Runtime setup

Runtime is the time a roller shutter, Venetian blind or awning requires for a complete move from

moved-in position to moved-out position. Runtime is also dependent on the height of the end products

and is a decisive factor for the correct moving to the intermediate positions (e.g. my-position, glare

protection and sun protection).

To set runtime, there are two possibilities available: manual or automatic.

Manual

Time can be set only when runtime of an end product has been determined (e.g. timed with a

stopwatch).

1. First set the minutes, up to 5, and conﬁrm.

2. Then set the seconds and conﬁrm .

Automatic

When runtime of the product is unknown, this can be set automatically.

Move end products upwards

The end products must be in the top-end position. This position is given as a reference point for the

exact positioning of the end products in "my" Position, glare protection or in sun protection position.

1. With the DOWN arrow, select "Start".

> The end products move up.

2. When they have reached the top, select "Stop".

Setting up Runtime

1. With the so key, select "ok/menu".

2. With the DOWN arrow, select "Start".

> The end products move down.

3. When the end products have reached the bottom, conﬁrm with

"ok/menu".

Runtime setup

Manual

Automatic

00m:15s

Manual runtime setup

Move product up

Stop

Start

Auto runtime setup

Stop

Start

10/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

4.5. Sun/light Sensor

- The wired sun/light sensor measures the actual brightness value that the sun function

requires.

- The radio sun/light sensor measures the actual brightness value that the Sun and Sunrise/

sunset Functions require.

Select the sensor between radio sensor, wired sensor or no sensor, and conﬁrm.

Note: Not all devices provide the possibilities mentioned above. See the selection table below.

Radio sensor Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S X

Chronis Smoove IB+ X

Soliris Smoove Uno X X

Soliris Smoove IB+ X X

- With "Radio sensor", you must pair the Sunis Wirefree io with

the device (see chapter "Pairing the Radio Sensor").

- With "No sensor", you can select a sensor later in the conﬁgura-

tion of the Sun Functions (see chapter "Settings menu").

Warning: When the radio sensor (Sunis Wirefree io) is already paired to another device, select the "No

sensor" option. You can pair the sensor later in the conﬁguration of the Sun Functions.

Light sensor setup

Radio sensor

No sensor

4. STARTING UP

11/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

4.6. Wind Sensor (Soliris versions)

- The wind sensor measures the actual wind speed that the Wind Function requires.

Select the sensor between wired or no sensor, and conﬁrm.

Note: Not all devices provide the possibilities mentioned above. See the selection table below.

Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S

Chronis Smoove IB+

Soliris Smoove Uno X

Soliris Smoove IB+ X

- With "No sensor", you can select a sensor later in the conﬁgu-

ration of the Wind Function (see chapter "Wind Function (Soliris

versions)").

Wind sensor setup

Wired sensor

No sensor

4. STARTING UP

12/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

4.7. Rain Sensor (Soliris versions)

- The rain sensor detects rain that the Rain Function requires.

Select the sensor between wired sensor or no sensor, and conﬁrm.

Note: Not all devices provide the possibilities mentioned above. See the selection table below.

Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S

Chronis Smoove IB+

Soliris Smoove Uno X

Soliris Smoove IB+ X

- With "No sensor", you can select a sensor later in the conﬁgu-

ration of the rain function (see chapter "Rain Function (Soliris

versions)").

4.8. End of initial settings

The basic settings are now complete and the time appears in the display.

With Chronis Smoove devices, the next predeﬁned Cycle Time also

appears.

Rain sensor setup

Wired sensor

No sensor

10:41

08:50

Sat.

20:00

4. STARTING UP

13/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

5. MANUAL MOVE COMMAND

In the main menu the following move commands can be made manually:

- UP symbol : Moves up and the symbol appears in the display.

- DOWN symbol : Moves down and the symbol appears in the display.

- "my" symbol : When the end products are moving, they are stopped. The symbol

appears in the display.

When the end products are stationary, they move to the already set

"my" position. In the display, the symbol appears.

Note for Venetian blinds operation:

A short press on the UP symbol tilts the Venetian blinds up.

A long press on the UP symbol moves the Venetian blinds up.

A short press on the DOWN symbol tilts the Venetian blinds down.

A long press on the DOWN symbol moves the Venetian blinds down.

If you give a short press or if there is a possibility that the end products only move very slightly, adjust

the start delay parameter (see "Back to Start delay").

Setting "my" Position

In the factory state, the "my" Position is 70% set (in the case of Venetian blinds without turn).

1. Move the end products to the desired position ("my") and use the "my-so key" to stop them.

2. Press "my-so key" for more than 5 seconds to save the new position.

> The following message appears: "My position set".

3. To delete the position, move the end products in the "my" Position.

4. Press the "my-so key" for more than 5 seconds.

> The following message appears: "My position cleared".

14/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

6. QUICK MENU

In the main menu, press shortly "ok/menu" (< 2s).

- The following mode can now be selected:

In the Quick menu, diﬀerent device operating modes can be set quickly.

6.1. Automatic

When activated, all automatic functions are carried out. Wind and Rain Functions always have priority

over Sun Functions or over timer commands. Manual operation is not possible during wind or rain

alarm.

The automatic mode is set as default.

In the display, only the activated functions are shown.

Example: the next time Cycle Time will appear in the display (UP move

command at 07:00).

6.2. Auto from

Current time +6, +12, or +18 hours: the automatic mode is switched oﬀ until this time. The automatic

function can be put out of operation for a limited time.

An intentional reactivating of the automatic functions is not necessary.

Example: "Auto from 16:23" means that the automatic functions (incl.

time Cycle Times) will activate the Cycle Times ﬁrst from 16:23 on. The

deactivating of the automatic is displayed with an arrow symbol and the

time up to when the deactivation is valid.

Auto mode

Auto from 16:51

Auto from 22:51

Holiday mode

Manual

Settings

10:55

Mon.

16:55

10:54

Thu.

07:00

15/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

6. QUICK MENU

6.3. Holiday mode

Presence can only be simulated when the timer is set with a ﬁxed time. The automatic Cycle Times

are randomly activated 15 minutes before or aer.

The Holiday mode is displayed with a suitcase.

Example: a ﬁxed cycle time is set for 7:00. In Holiday mode, the move

commands are carried out randomly between 06:45 and 07:15. Further

set functions such as sun, wind, rain, or cycle times of sunrise and sunset

remain active.

6.4. Manual

All automatic functions (incl. time Cycle Times) except safety relevant

functions, such as wind and rain, are deactivated.

Only the time is displayed.

6.5. Settings

1. Select the appropriate mode.

2. Conﬁrm your selection.

See chapter "Settings menu".

10:56

Mon.

16:55

16/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

7. SETTINGS MENU

In the Settings menu, the automatic functions can be set and the basic conﬁguration of the device can

be changed:

- Prog. timer

- Sun Function (only with Chronis Smoove UNO S and Soliris

Smoove devices)

- Wind Function (only with Soliris Smoove devices)

- Rain Function (only with Soliris Smoove devices)

- Conﬁguration: Language, Time, Date, Operating Mode, Display

1. In the "Quick Menu", select the menu "Settings" (see "Starting up").

2. In the main display, press the "ok/menu" so key for more than 2secs.

7.1. Program Timer / Cycle Times

Each day, two (with Chronis Smoove UNO, Cycle Time 1 to Cycle Time 2), or four diﬀerent timer

commands (with Chronis Smoove UNO S and Soliris Smoove devices, Cycle Time 1 to Cycle Time 4)

can be carried out. A timer command activates a move of the end products (e.g. a downward move in

the evening or an upward move in the morning). As a rule, the end products require two Cycle Times

per day (e.g. morning up and evenings down).

The timer commands can depend on either the time or on Sunrise/sunset.

Factory settings

With all Chronis and Soliris Smoove devices, Cycle Times 1 and 2 are already set and switched on:

- Cycle Time 1: switched on, UP command, Mon-Fri at 7:30, Sat-Sun at 8:30

- Cycle Time 2: switched on, DOWN command every day at 20:00

1. Conﬁrm the "Prog. Timer" function to carry out timer commands.

2. Select the Cycle Time (depending on model, 1 to 2 or 1 to 4) and conﬁrm.

Switching ON/OFF

You can switch the function on and oﬀ.

1. Conﬁrm the function.

2. Switch the function on or oﬀ with the DOWN or UP arrow.

Configuration menu

Prog. timer

Sun Function

Configuration menu

Wind Function

Rain Function

Configuration menu

Rain Function

Configuration

Prog. timer

Cycle Time 1

Cycle Time 2

Cycle Time 1

ON/OFF Cycle Time

Configuration

Cycle Time 1

OFF

17/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

7. SETTINGS MENU

Conﬁguration of Cycle Times

The Cycle Times are deﬁned with the Position, Day, Time (Time or

depending on Sunrise/sunset).

Go to the "Conﬁguration" sub menu. You will be guided to the next step.

Position

Select the required position of the end products on the timer between the

following possibilities and conﬁrm the position.

- Up (top), Down (bottom)

- Glare protection (not with Chronis Smoove Uno): mostly used in

connection with sun automatism

- Intimacy (not with Chronis Smoove Uno): mostly evenings when

one does not wish to be seen

- my Position: a position freely deﬁnable by the user, also acces-

sible over the my so key

- Position 2 (not with Chronis Smoove Uno): a second position

deﬁnable by the user

The Glare protection and Intimacy positions are programmed with preset values but they can also be

changed (see "Conﬁguration of Cycle Times").

Glare protection Intimacy

Roller shutters 70% 90%

Venetian blinds 100%, angle 0.5s 100%, angle 0s

Awnings 100% 100%

Note for Venetian blinds operation:

100% position means that the Venetian blinds move completely downwards.

Angle 0.5s means that the blinds, aer moving downwards, move again upwards for 0.5 seconds and

thus tilt out the slats.

Cycle Time 1

ON/OFF Cycle Time

Configuration

Cycle Time 1

Down

Cycle Time 1

Glare protection

Intimacy

Cycle Time 1

my Position

Position 2

18/40

Chronis & Soliris Smoove

[ Back to Contents ]

Interactive operating instructions

Day

Determine on which day the end products should move to the selected position.

• Select between the following options and conﬁrm your selection:

- Week: the cycle time is sent every day at the same time

- Mon - Fri: the cycle time is sent from Monday to Friday at the

same time

- Sat - Sun : the cycle time is sent from Saturday to Sunday at

the same time

- Mon, Tues, Wed, Thurs, Fri, Sat, Sun: the cycle time is sent

individually each day

Setting Time

Determine at what time the cycle times are activated.

1. With the arrow, select the following option and conﬁrm.

2. Select the time and conﬁrm.

3. Set the minutes and conﬁrm.

Setting Time depending on Sunrise/sunset

Determine whether the Cycle Time should be activated at sunrise (sun

symbol), or at sunset (moon symbol) instead of a ﬁxed time.

Chronis Smoove UNO has been programmed only with sunset.

1. With the arrow, select the following option and conﬁrm.

2. Press the "back" so key to quit and save the time setting.

07:30

--:--

Cycle 1 - Up

Week

Mon.-Fri.

07:30