Hoshizaki KMD-210ABE-HC User manual

KMD-210ABE-HC
L1M099201 (112021)
MODULAR CRESCENT CUBER
MACHINE A GLACONS CROISSANT MODULAIRE
MODULARER CRESCENTEISBEREITER
MODULAIRE MACHINE VOOR HALVEMAANVORMIGE IJSBLOKJES
MÁQUINA MODULAR DE CUBITOS EN FORMA DE MEDIA LUNA
FABBRICATORE DI GHIACCIO IN CUBETTI MODULARE A FORMA DI MEZZALUNA
INSTRUCTION MANUAL
(original instructions)
NOTICE D’UTILISATION
(instructions traduites)
BEDIENUNGSANLEITUNG
(Übersetzung)
GEBRUIKSAANWIJZING
(vertaalde instructies)
MANUAL DE INSTRUCCIONES
(instrucciones traducidas)
MANUALE D’ISTRUZIONI
(traduzione)
Telford 70 Sta󰀨ord Park 7, Telford, Shropshire TF3 3BQ UK

ENGLISH
1
IMPORTANT SAFETY INFORMATION
Throughout this manual, notices appear to bring your attention to situations which could result in
death, serious injury, or damage to the unit.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTICE Indicates a hazardous situation which, if not avoided, could result in damage
to the unit.
HYGIENE Indicates important precautions for hygiene and food safety.
IMPORTANT Indicates important information about the use and care of the unit.
This icemaker uses HFC-free refrigerant (propane) and HFC-free foam insulation that are non-
ozone-depleting and environmentally sustainable materials having very low global warming
potential.
WARNING
This icemaker contains ammable refrigerant in its cooling unit; installation, handling, servicing
and disposal must therefore only be carried out by authorized technicians.
The refrigerant contained in this icemaker is ammable and sealed in the refrigeration system.
Although the refrigerant does not leak out under normal usage, take utmost care when
handling this icemaker so as not to cause any damages to the system.
In the case of accidental damage to the refrigeration system causing refrigerant leak:
* Do not create a source of ignition in the area.
* Do not operate electrical switches or plugs in the area.
* Do not use naked ame.
* Immediately ventilate the area by opening doors and/or windows.
* Call service engineer.
IMPORTANT
This booklet is an integral and essential part of the product and should be kept and preserved
by the user.
Please read carefully the guidelines and warnings contained herein as they are intended
to provide the installer/user with essential information for the proper installation and the
continued safe use and maintenance of the product.
Please preserve this booklet for any further consultation that may be necessary.

ENGLISH
2
WARNING
This is a commercial icemaker, and should be destined only to be used for the purpose for
which it has been expressly designed.
Any other use should be considered improper and therefore dangerous. The manufacturer
will not be held liable or responsible for any damage caused by improper, incorrect and
unreasonable use.
The installation, and relocation if necessary, must be carried out by qualied personnel,
in accordance with current regulations, according to the manufacturer’s instructions.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process, other
than those recommended by the manufacturer.
The use of any electrical appliance involves the observance of some fundamental rules. In
particular:
*Instances of high humidity and moisture increase the risk of electrical short circuits and
potential electrical shocks. If in doubt, disconnect the icemaker.
*Do not damage the power cord or pull it in order to disconnect the icemaker from the
electrical supply network.
*If the supply cord is damaged, it must be replaced by a replacement cord available from
Hoshizaki Parts/Service Centres.
*Do not touch the electrical parts or operate the switches with damp hands.
*This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, it can however be used
by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge providing they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
*Children shall not play with the appliance.
*Cleaning and user maintenance shall not be made by children without supervision.
* Do not attempt to modify the icemaker. Only qualied personnel may disassemble or repair
the appliance.

ENGLISH
3
I. INSTALLATION INSTRUCTIONS
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging elements
(plastic bags and expanded polystyrene) as they are potential
sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing material
is left in the icemaker, it will not work properly.
3) Disconnect the discharge hose.
4) Disconnect the pump motor connector and oat switch connector
from the side of the control box.
5) Pull out the water tank, cube guide, pump motor bracket, pump motor
and oat switch together. See Fig. 4.
Front Panel
Top Insulation
Side Panel
Screws
Screw
Top Panel
Side Frame
Front Frame
Front Insulation
Thumbscrews
Fig. 1
when air temperature is below zero (see “II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE”).
8. Avoid prolonged exposure of the appliance to direct sunlight.
3. INSTALLATION
* Incorrect installation can cause harm to people, animals
or things, for which the manufacturer cannot be held
responsible.
* Place the icemaker on top of the storage bin/dispenser
unit by holding the bottom.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is
accessible.
* Level the dispenser unit/ice storage bin in both the
left-to-right and front-to-rear directions. If using an ice
storage bin, adjust the ice storage bin legs to level. See
Fig. 2.
4. BIN CONTROL INSTALLATION
1) Remove the front panel, then remove the front insulation.
2) Loosen the two thumbscrews securing the pump motor bracket. See
Fig. 3.
Fig. 4
Pump Motor
Float Switch
Cube Guide Snap Tab
1) After removing the packaging, make sure that the icemaker is in good
condition. If in doubt, please do not use the equipment but apply to
professionally qualied personnel.
2) Remove shipping tape holding the components.
3) Remove the protective plastic lm from the exterior. If the icemaker
is exposed to the sun or to heat, remove the lm after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Power Supply Cord 1
b) Mounting Bracket 2
c) Bolt 2
2. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor use. Normal operating
ambient temperature should be within 7°C to 40°C. Normal
operating water temperature should be within 7°C to 35°C.
Operation of the icemaker, for extended periods, outside
of these normal temperature ranges may a󰀨ect production
capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a rm and level foundation for the
equipment.
4. Allow 15 cm clearance at rear, left side and top and 30 cm
clearance at right side for proper air circulation and ease of
maintenance and/or service should they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of the
louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
Fig. 3
Float Switch
Connector
Pump Motor
Connector
Discharge
Hose
Thumbscrews
Snap Tab
Pump Motor Bracket
Fig. 2
Max. 5mm

ENGLISH
4
6) Route the bin control lead through the hole in the base, then into
the bushing provided. See Fig. 5.
Bushing
Bin Control Lead
Fig. 5
Bushing
7) While pulling up the bin control lead, hook the bin control on the right
side interior wall. Then push the bin control up against the bottom of
the unit, and slide to the back until it snaps in place. Make sure the
slotted holes at the right side of the bin control are securely placed
on the collars at the bottom of the unit. See Fig. 6.
CAUTION
Make sure the bin control is securely in place. Otherwise, ice may
get between gaps and damage the bin control.
Fig. 6
Bin Control
Collars
11) Secure the pump motor bracket with the two thumbscrews.
12) Reconnect the pump motor connector and oat switch connector.
13) Replace the front insulation and front panel in their correct positions.
5. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local
electrical code requirements. To prevent possible severe electrical
shock to individuals or extensive damage to equipment, install a
proper earth wire to the icemaker. Remove the plug from the mains
socket before any maintenance, repairs or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
* The main control box fuse is rated at 5A, 250V and should only be
replaced by a qualied service engineer.
* Usually an electrical permit and services of a licensed electrician are
required.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol or coloured Green or Green-and-Yellow. The wire which
is coloured Blue must be connected to the terminal which is marked
with the letter N or coloured Black. The wire which is coloured Brown
must be connected to the terminal which is marked with the letter L
or coloured Red.
* Should the socket outlets in the installation site not be suitable for the
plug supplied with your product, the plug must be removed (cut o󰀨 if
it is moulded on plug) and an appropriate plug tted.
If the non-rewirable plug has been cut from the power supply cord, it
must be disposed of. There should be no attempt to reuse it. Inserting
such a plug into a socket elsewhere presents a serious risk of electrical
shock.
* The non-rewirable plug must never be used without a fuse cover being
tted.
The correct replacement for the detachable fuse cover is identiable
from the manufacturer’s reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 10A and approved to BS 1362.
6. WATER SUPPLY AND DRAIN CONNECTIONS
WARNING
Connect to potable water supply only.
* The connections to the mains water supply must be made in
accordance with the countries’ current requirements of the Water
Supply or Water Fittings Regulations.
8) Pull up any slack in the bin control lead, then put the bushing attached
to the bin control lead back into the hole in the base.
9) Connect the bin control connector to the side of the control box.
10) Replace the water tank, cube guide, pump motor bracket, pump
motor and float switch in their correct positions. The pump
motor bracket must be attached securely to the back so that the
thumbscrews can be tightened.
CAUTION
Be sure to let the discharge hose pass behind the copper tube
and connect it securely in position. See Fig. 3. Otherwise, the
discharge hose may be caught in the front insulation, leading to
improper results.

ENGLISH
5
* To avoid performance reduction or malfunction caused by scaling, the
water supply should have a hardness of not more than 50 mg/L and
a silica content of not more than 30 mg/L. Otherwise, installation of a
proper water treatment device will be required.
* Water supply pressure should be minimum 0.07 MPa (0.7 bar) and
maximum 0.8 MPa (8 bar). If the pressure exceeds 0.8 MPa (8 bar),
use a pressure reducing valve. Do NOT throttle back the supply tap.
* A plumbing permit and services of a licensed plumber may be required
in some areas.
* Water should drain into an open trap.
* The icemaker drain is gravity ow, so ensure drain pipe has an
adequate pitch or fall.
* A vented tee connection is required for proper drain ow. See Fig. 7.
* The icemaker drain line must be run separately from the storage bin/
dispenser unit drain line. See Fig. 7.
* There should be no backow in the water circuit.
* Water supply connection is intended to be made by means of a pipe,
not a hose set.
Note: Jointing compounds should be approved and suitable for potable
water use.
1. OPERATION
The installer will normally commission the icemaker to start the automatic
icemaking process. To ensure continuous operation, make sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply.
2. PREPARING THE ICEMAKER FOR LONG STORAGE
1) Turn o󰀨 the circuit breaker.
2) Close the water supply line shut-o󰀨 valve.
3) Remove all ice from the storage bin/dispenser, and clean the bin/
dispenser.
4) Ask for draining of the icemaker by professional qualied personnel.
III. MAINTENANCE
1. CLEANING
WARNING
1. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to clean and sanitise the icemaker
water system at least twice a year and to check and clean the
condenser at least once a year.
3. This appliance must not be cleaned by use of a water jet.
4. Do not use any alcohol for cleaning/sanitisation of the icemaker.
It may cause cracks on the plastic parts.
5. To prevent possible damage, do not clean the plastic parts
with water above 40°C or in a dishwasher.
[1] Machine and Bin Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use a
damp cloth containing a neutral cleaner to wipe o󰀨 grease or dirt.
[2] Scoop
1) Either mix 3 litres of water with 11 ml of 5.25% sodium hypochlorite
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
2) Soak the scoop in the solution for more than 3 minutes. Rinse
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
1) Open the storage bin door, and remove all ice.
Note: Hoshizaki recommends various types of storage bin for
the icemaker which vary in size and design. The following
instructions are therefore for general guidance only.
2) Wash the bin liner and door inner surface with a neutral non-abrasive
cleaner. Rinse thoroughly with a clean cloth and fresh water.
3) Either mix 5 litres of water with 18 ml of 5.25% sodium hypochlorite
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
4) Soak a clean sponge or cloth with the solution, and wipe the bin liner
and door inner surface.
5) Rinse thoroughly with fresh water and a clean cloth to wipe o󰀨 the
solution. Close the bin door.
Fig. 7
Icemaker Water
Supply Inlet
1/2”FPT
Icemaker
Drain Outlet
3/4”FPT
Icemaker
Water Supply Line
Shut-O󰀨 Valve
Icemaker
Water Supply Line
Drain Valve
Bin Drain Outlet
3/4”FPT
Bin
5cm air gap
Separate piping to approved
drain. Leave a 5cm vertical
air gap between the end of
each pipe and the drain.
Drain
Floor
Icemaker
II. OPERATING INSTRUCTIONS
WARNING
1. This icemaker is designed to produce edible ice. To keep the
icemaker hygienic:
* Wash your hands before removing ice. Use the plastic scoop
provided (accessory).
* The storage bin is for ice use only. Do not store anything else
in the bin.
* Clean the storage bin before use (see “III. 1. CLEANING”).
* Keep the scoop clean. Clean it by using a neutral cleaner
and rinse thoroughly.
* Close the door after removing ice to prevent entrance of dirt,
dust or insects into the storage bin.
2. All parts are factory-adjusted. Improper adjustments may result
in failure.
3. If the unit is turned o󰀨, wait for at least 3 minutes before
restarting the icemaker to prevent damage to the compressor.

ENGLISH
6
Note: Some solutions may cause damage to the bin liner surfaces or
corrosion on the metal parts. Always rinse the sanitiser unless
directed otherwise by Hoshizaki guidelines.
[4] Air Filter
Plastic mesh air lters remove dirt or dust from the air, and keep the
condenser from getting clogged. If the lters get clogged, the icemaker’s
performance will be reduced. Remove and clean the air lters at least
twice per month:
1) Remove the air lter.
Note: Do not put your hand inside the machine compartment.
2) Clean the air lter by using a vacuum cleaner. When severely clogged,
use warm water and a neutral cleaner to wash the air lter.
3) Rinse and dry the air lter thoroughly, and place it in position.
[5] Icemaking Water System
To keep the icemaker hygienic, periodic cleaning of the icemaking water
system is recommended. Always ask a trained service person to clean
the water system.
2. BEFORE CALLING A SERVICE AGENT
WARNING
Do not damage the refrigerant circuit.
If the icemaker does not work properly or does not work at all, before
calling for service, check that:
* The power is supplied to the unit.
* The water is turned on.
* The air lter is clean.
For further assistance or advice, contact your local Hoshizaki service
agent.
3. WARRANTY
Hoshizaki warrants to the original owner/user that all Hoshizaki branded
products shall be free of defects in material and/or workmanship for the
duration of the “warranty period”. The warranty shall be e󰀨ective for two
years from the date of installation.
Hoshizaki’s liability under the terms of the warranty are limited and
shall exclude routine servicing, cleaning, essential maintenance and/or
repairs occasioned by misuse and installations not in accordance with
Hoshizaki guidelines.
Warranty repairs should be completed by an approved Hoshizaki dealer
or service agency using genuine Hoshizaki components.
To obtain full details of your warranty and approved service agency,
please contact your dealer/supplier, or the nearest Hoshizaki Service
o󰀩ce:
Europe, Middle East, Africa
Hoshizaki UK - UK, Ireland
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Deutschland - Germany, Switzerland, Austria, Poland, Czech
Republic, Slovakia
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki France - France
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Iberia - Spain, Portugal
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Middle East - Middle East
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Benelux - Netherlands, Belgium, Luxembourg
Tel: [phone]
[email protected]
Hoshizaki Italia - Italy
TEL: [phone]
TEL: [phone]
[email protected]
Hoshizaki Europe B.V. - all other countries within Europe and Africa
TEL: [phone]
FAX: [phone]
[email protected]
Asia, Oceania
Hoshizaki Singapore
TEL: [phone]
FAX: [phone]
[email protected] (Sales)
[email protected] (Technical support)
Hoshizaki Taiwan
TEL: [phone]
FAX: [phone]
Hoshizaki Hong Kong
TEL: [phone]
FAX: [phone]
IV. DISPOSAL
Comply with local regulations regarding disposal of this appliance and
its refrigerant gas. Before you scrap the appliance, take o󰀨 the door to
prevent children trapped.
Correct disposal of this product:
This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources.
To return your used device, use the return and collection
systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
WARNING
The insulation foaming agent used for the unit body
contains ammable gas cyclopentane. With this in
mind, dispose of the product properly.

FRANÇAIS
7
INFORMATIONS DE SECURITE IMPORTANTES
Tout au long de ce manuel, des avis attirent votre attention sur des situations qui pourraient
entraîner la mort, des blessures graves ou des dégâts à l’appareil.
AVERTISSEMENT Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures graves voire mortelles.
ATTENTION Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures mineures ou modérées.
AVIS Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des dégâts à l’appareil.
HYGIENE Signale des précautions importantes à prendre en matière d’hygiène et
de sécurité alimentaire.
IMPORTANT Signale des informations importantes sur l’utilisation de l’appareil et son
entretien.
La machine à glace emploie du uide frigorigène exempt de HFC (propane) et une isolation en
mousse exempte de HFC, non nocifs pour la couche d’ozone, ainsi que des matériaux durables
qui ont très peu d’impact sur le réchau󰀨ement mondial.
AVERTISSEMENT
L’unité de refroidissement de la machine à glace contenant des uides frigorigènes inammables,
son entretien et son rechargement ne doivent être réalisés que par des techniciens agréés.
Le uide frigorigène de cette machine à glace est inammable et est enfermé dans le système
de réfrigération. Bien que le fluide frigorigène ne présente aucun risque de fuite dans des
conditions d’utilisation normales, manipulez la machine à glace avec la plus grande précaution
an d’éviter d’endommager le système.
En cas de fuite de fluide frigorigène résultant d’un dommage accidentel au système de
réfrigération :
* Interdire toute étincelle ou corps incandescent dans le voisinage.
* N’utiliser aucun interrupteur ni prise électrique dans le voisinage.
* Ne pas utiliser de amme nue.
* Ventiler immédiatement la pièce en ouvrant les portes et/ou fenêtres.
* Appeler un technicien de réparation.
IMPORTANT
Ce livret est un élément essentiel qui fait partie intégrante du produit et il doit être conservé
soigneusement par l’utilisateur.
Veuillez lire attentivement les conseils et les avertissements qui s’y trouvent, car ils ont pour
but de fournir à l’installateur et à l’utilisateur des informations essentielles pour une installation
correcte, une utilisation en toute sécurité et un entretien adéquat du produit.
Veuillez conserver précieusement ce livret pour toute référence ultérieure.

FRANÇAIS
8
AVERTISSEMENT
Cette machine à glace a été conçue pour des applications commerciales ; elle ne peut être
utilisée qu’aux ns auxquelles elle est expressément destinée.
Toute autre utilisation doit être considérée comme inappropriée et donc dangereuse.
Le fabricant décline toute responsabilité pour les dégâts provoqués par une utilisation
inappropriée, incorrecte et abusive.
L’installation, et le transfert le cas échéant, doivent être effectués par un personnel
qualié, conformément aux réglementations en vigueur et aux consignes du fabricant.
Veillez à ce que les ouvertures de ventilation de l’enceinte de l’appareil et de la structure
intégrée ne soient pas obstruées.
Pour accélérer le processus de décongélation, ne pas utiliser d’équipements mécaniques ni
des méthodes autres que celles recommandées par le fabricant.
L’utilisation de tout appareil électrique implique le respect de certaines règles fondamentales.
En particulier :
*En cas de forte humidité, les risques de court-circuit et d’électrocution augmentent. En cas
de doute, débrancher la machine à glace.
*Ne pas endommager le cordon d’alimentation et ne pas tirer sur le cordon d’alimentation pour
débrancher la machine à glace.
*Si le cordon d’alimentation est endommagé, il doit être remplacé par un cordon de rechange
disponible auprès des centres de pièces détachées et d’entretien Hoshizaki.
*Ne pas toucher les pièces électriques ou les commutateurs avec les mains humides.
* Cette machine n’est pas prévue pour une utilisation par des personnes (y compris des
enfants) aux capacités physiques, sensorielles ou mentales réduites, ou manquant
d’expérience ou de connaissances. Elle peut cependant être utilisée par des enfants d’au
moins 8 ans et des personnes aux capacités physiques, sensorielles ou mentales réduites,
ou manquant d’expérience ou de connaissances, si une personne responsable de leur
sécurité les surveille ou leur a indiqué les consignes d’utilisation de la machine.
*Les enfants ne doivent pas jouer avec la machine.
*Le nettoyage et l’entretien régulier ne doivent pas être effectués par des enfants sans
surveillance.
* Ne pas tenter de modier la machine à glace. Cet appareil ne peut être démonté ou réparé
que par du personnel qualié.

FRANÇAIS
9
I. CONSIGNES D’INSTALLATION
1. DEBALLAGE
AVERTISSEMENT
Les enfants doivent être tenus à l’écart des éléments d’emballage
(sacs en plastique et polystyrène expansé) car ils constituent des
sources de danger potentielles.
ATTENTION
Enlever le carton de transport, le ruban adhésif et le matériel
d’emballage. S’il reste des matériaux d’emballage dans la machine
à glace, elle ne fonctionnera pas correctement.
1) Une fois les matériaux d’emballage enlevés, vérier que la machine
à glace est en bon état. En cas de doute, ne pas utiliser l’appareil et
faire appel à un technicien qualié.
2) Enlevez le ruban adhésif qui retient les composants pour le transport.
3) Retirer le lm protecteur en plastique recouvrant l’extérieur. Si la
machine à glace a été exposée au soleil ou à la chaleur, la laisser
refroidir avant d’enlever le lm.
4) Retirer le paquet d’accessoires et vérier son contenu :
a) Cordon d’alimentation électrique 1
b) Support de xation 2
c) Boulon 2
2. EMPLACEMENT
IMPORTANT
1. Cette machine à glace n’est pas conçue pour être utilisée à
l’extérieur. La température ambiante normale de service doit
être comprise entre 7 °C et 40 °C. La température normale
de service de l’eau doit être comprise entre 7 °C et 35 °C.
Un fonctionnement prolongé de la machine en dehors de
ces plages de températures risque d’a󰀨ecter la capacité de
production de glace.
2. La machine à glace ne doit pas être placée à proximité de
fours, de grills ou de toute autre source de chaleur importante.
3. La machine doit avoir une assise solide et horizontale.
4. Pour assurer une bonne circulation d’air et faciliter les
opérations de maintenance et/ou d’entretien, prévoir 15 cm de
dégagement à l’arrière, sur le côté gauche et sur le dessus de
la machine, et 30 cm de dégagement sur le côté droit.
5. Cette machine ne doit pas être installée dans un local où l’on
risque d’utiliser un jet d’eau ou dans lequel l’utilisation de
matériel produisant des gouttes d’eau est préjudiciable.
6. Ne rien poser sur le dessus de la machine ni devant le volet
d’aération.
Front Panel
Top Insulation
Side Panel
Screws
Screw
Top Panel
Side Frame
Front Frame
Front Insulation
Thumbscrews
Fig. 1
7. La machine à glace ne fonctionnera pas aux températures
au-dessous de zéro. Pour prévenir tout dommage à la
conduite d’alimentation en eau, vidanger la machine à glace
lorsque la température de l’air est inférieure à zéro (voir « II.
2. PREPARATION DU DISTRIBUTEUR DE GLACE EN VUE
D’UN ENTREPOSAGE DE LONGUE DUREE »).
8. Eviter toute exposition prolongée de l’appareil à la lumière
directe du soleil.
3. INSTALLATION
* Une installation incorrecte de la machine peut avoir des conséquences
néfastes sur les personnes, les animaux ou les choses, pour lesquelles
le fabricant ne peut être tenu responsable.
* Placer la machine à glace au-dessus du bac de
stockage/distributeur en tenant sa partie inférieure.
* Placer la machine à glace à l’endroit choisi pour son
installation.
* L’appareil doit être placé de telle sorte que la che soit
accessible.
* Ajustez le niveau de l’unité de distribution/du bac de
stockage de glaçons dans les axes gauche/droite et
avant/arrière. Si vous utilisez le bac de stockage de
glaçons, ajustez ses pieds an de les mettre à niveau.
Voir g. 2.
4. INSTALLATION DE LA COMMANDE DU BAC
1) Retirer le panneau avant, puis l’isolation avant.
2) Desserrer les deux vis à oreilles xant le support du moteur de la
pompe. Voir g. 3.
3) Débrancher le tuyau de déchargement.
4) Débrancher le connecteur du moteur de la pompe et le connecteur
du commutateur à otteur du côté du boîtier de commande.
5) Retirer ensemble le réservoir d’eau, le guide glaçons, le support du
moteur de la pompe, le moteur de la pompe et le commutateur à
otteur. Voir g. 4.
6) Faire passer le l de la commande du bac par l’orice situé à la
base, puis dans le passe-l fourni. Voir g. 5.
7) Tout en tirant le l de la commande du bac vers le haut, xer la
commande du bac sur la paroi intérieure, du côté droit. Soulever
ensuite la commande du bac contre la partie inférieure de l’appareil
et la faire glisser vers l’arrière jusqu’à ce qu’un déclic conrme
sa mise en place. Les trous à rainures situés du côté droit de la
commande du bac doivent être placés sur les bagues, au niveau
de la partie inférieure de l’appareil. Voir g. 6.
ATTENTION
La commande du bac doit être bien placée, faute de quoi de la
glace risque de se coincer dans les trous et l’endommager.
Fig. 3
Connecteur du
commutateur à
otteur
Connecteur du
moteur de la
pompe
Flexible
de vidange
Vis à oreilles
Languette à encliqueter
Support du moteur de la pompe
Isolation supérieure
Isolation avant
Panneau avant
Vis
Vis Panneau avant
Armature
latérale
Armature avant
Vis à oreilles
Panneau
supérieur
Fig. 2
5 mm max.