Cornelius UC150 ICE ONLY User manual

ICE DISPENSER
Model: UC150 ICE ONLY
Operator’s Manual
PRINTED IN U.S.A
IMI CORNELIUS INC; 1999–2005©
IMI CORNELIUS INC
www.cornelius.com
Part No. 620917311
August, 1999
Revision Date: December 16, 2005
Revision: B
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment

i620917311
TABLE OF CONTENTS
Page
SAFETY INFORMATION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RECOGNIZE SAFETY INFORMATION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTAND SIGNAL WORDS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FOLLOW SAFETY INSTRUCTIONS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CO2 (CARBON DIOXIDE) WARNING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHIPPING, STORING, OR RELOCATING UNIT 1. . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION INSTRUCTIONS 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAILY (OR AS REQUIRED) 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MONTHLY 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
START-UP & OPERATING INSTRUCTIONS 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TORSION BAR REMOVAL 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND SANITIZING INSTRUCTIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . .
DISPENSER 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUGER ASSEMBLY BREAKDOWN 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPEED CONTROL FOR ICE DELIVERY 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLOWN FUSE OR CIRCUIT BREAKER. 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AGITATOR DOES NOT TURN, AUGER DOES NOT TURN. 15. . . . . . . . . . . . . . . . .
ICE DISPENSES CONTINUOUSLY. 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLUSHY ICE. WATER IN HOPPER. 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AGITATOR TURNS, AUGER DOES NOT TURN. 15. . . . . . . . . . . . . . . . . . . . . . . . . .
AUGER TURNS, AGITATOR DOES NOT. 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UC 150 PARTS LIST 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UC 150 PARTS LIST (CONT’D) 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UC 150 PART LIST (CONT’D) 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIST OF FIGURES
FIGURE 1. TEMPLATE 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 2. DIMENSIONS TEMPLATE 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 3. TORSION BAR REMOVAL 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 4. AUGER ASSEMBLY 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 5. ICE AUGER MOTOR 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 6. WIRING DIAGRAM 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 7. LADDER DIAGRAM 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 8. US 150 EXPLODED VIEW 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 9. AGITATOR MOTOR AND DISPENSE SWITCH WIRING DETAIL 17. .
FIGURE 10. WIRING DIAGRAM 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 11. UC 150 PLUMBING 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1620917311
SAFETY INFORMATION
Recognize Safety Information
This is the safety-alert symbol. When you see this
symbol on our machine or in this manual, be alert to
the potentially of personal injury.
Follow recommended precautions and safe operating
practices.
DANGER
Understand Signal Words
A signal word - DANGER, WARNING, OR CAUTION
is used with the safety-alert symbol. DANGER identi-
fies the most serious hazards.
Safety signs with signal word DANGER or WARNING
are typically near specific hazards. WARNING
General precautions are listed on CAUTION safety
signs. CAUTION also calls attention to safety mes-
sages in this manual. CAUTION
Follow Safety Instructions
Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in
good condition. Replace missing or damaged safety signs. Learn how to operate the machine and how to
use the controls properly. Do not let anyone operate the machine without instructions. Keep your machine in
proper working condition. Unauthorized modifications to the machine may impair function and/or safety and
affect the machine life.
CO2(Carbon Dioxide) Warning
CO2Displaces Oxygen. Strict Attention must be observed in the prevention of CO2(carbon dioxide)
gas leaks in the entire CO2and soft drink system. If a CO2gas leak is suspected, particularly in a
small area, immediately ventilate the contaminated area before attempting to repair the leak. Person-
nel exposed to high concentration of CO2gas will experience tremors which are followed rapidly by
loss of consciousness and suffocation.
CAUTION: Before shipping, storing, or relocating this Unit, the syrup systems must be sanitized and
all sanitizing solution must be purged from the syrup systems. All water must also be purged from
the plain and carbonated water systems. A freezing ambient temperature will cause residual water
remaining inside the Unit to freeze resulting in damage to internal components of the Unit.
Shipping, Storing, Or Relocating Unit

2620917311
THIS PAGE LEFT BLANK INTENTIONALLY

3620917311
SAFETY PRECAUTIONS
This ice dispenser has been specifically designed to provide protection against personal injury and eliminate con-
tamination of ice. To ensure continued protection and sanitation, observe the following:
ALWAYS: disconnect power to the dispenser before servicing or cleaning.
NEVER: place hands inside of hopper or gate area without disconnecting power to the dispens-
er. Agitator rotation occurs automatically when dispenser is energized!
ALWAYS: be sure the removable lid is properly installed to prevent unauthorized access to the hopper interior and
possible contamination of the ice.
ALWAYS: be sure the upper and lower front panels are securely fastened.
ALWAYS: keep area around the dispenser clean of ice cubes.
CAUTION: Dispenser cannot be used with crushed or flaked ice.
Use of bagged, ice which has frozen into large chunks, can void warranty.
The dispenser agitator is not designed to be an ice crusher. Use of large
chunks of ice which “jam up” inside the hopper will cause failure of the agitator
motor and damage to the hopper. If bagged ice is used, it must be carefully and
completely broken into small, cube-sized pieces before filling into the dispenser
hopper.
DESCRIPTION
The Undercounter ice dispenser solves your ice service needs in a sanitary, space saving, economical way. De-
signed to be manually filled with ice this dispenser will dispense cubes (up to 1-1/4” in size), cubelets and hard-
chipped or cracked ice
SPECIFICATIONS
Model: UC150
Ice Storage: 150 lbs
Electrical: 120/1/60, 3 amps total unit draw
Dimensions: 30” Wide X 33–5/8” Deep X 27” Below Countertop
16–9/16” High Above Countertop

4
620917311
12.18812.188
29.875
R .500
R .500 TYP.
BEVEL BEVEL
BEVEL
5.250
BEVEL
9.125
9.688
9.125
25.438
CORIAN IS CUT FROM COUNTER AND IS REWORKED AS SHOWN ABOVE BEFORE BEING GLUED
TO UC 150 DOOR LIDS
7.00
OPTIONAL: CORIAN COUNTERTOPS ARE ATTACHABLE AND BLEND INTO RESTAURANT
DECOR. (SUPPLIED BY KES). CORIAN IS CUT FROM COUNTER AND
FABRICATED (SEE FIGURE 1).
FIGURE 1. TEMPLATE

5620917311
FOOT PRINT OF
UNIT ON COUNTER
COUNTER CUT
OUT FOR UNIT
TO DROP IN CLEARANCE
NEEDED FOR
OPENING LID
27 – 3/8
1– 15/16
2–1/2
33–1/2 31–7/8
30
32–1/2
13/16
THE ABOVE FIGURE SHOWS THE REQUIRED CUTOUT FOR PLACING THE ICE DISPENSER INTO A COUNTER TOP. THE DOTTED
LINE IS THE ACTUAL CUTOUT DIMENSIONS WHILE THE SOLID LINE SHOWS THE AMOUNT OF OVERHANG FOR THE DISPENSER.
FIGURE 2. DIMENSIONS TEMPLATE

6
620917311
INSTALLATION INSTRUCTIONS
IMPORTANT: It is the responsibility of the installer to ensure that the drains from the dispensing
equipment is installed and maintained according to Federal, State and Local Laws.
1. Locate the dispenser indoors on a level counter top.
A. COUNTER MOUNTING
The ice dispenser must be sealed to the counter. The template drawing indicates the opening that must
be cut in the counter. Locate the desired position for the dispenser, then mark the outline dimensions on
the counter using the template drawings. Cut openings in counter.
Apply a continuous bead of NSF International (NSF) listed silastic sealant (Dow 732 or equal) approxi-
mately 1/4” inside of the unit outline dimensions and around all openings. Then, position the unit on the
counter within the outline dimensions. All excess sealant must be wiped away immediately.
2. The drain tube is routed through the large opening in the bottom of the unit. See the MOUNTING TEMPLATE
(page 5) for locating the required clearance hole in the counter for these utility lines. The power cord is
routed through the holes in the side of the unit.
3. SINK DRAIN ASSEMBLY: Connect the drain tube to an open drain. Additional drain tubing is provided with
the unit. The drain tube must continuously pitch downward and contain no “traps” or improper drainage will
result.
A. Use 3/4Inominal plastic pipe.
B. To assure proper drainage, do not allow “trap” to form in drain line. Be sure drain line runs flat with bot-
tom of dispenser.
NOTE: This equipment must be installed with adequate backflow protection to comply with federal, state,
and local codes.
4. Clean the hopper interior (see CLEANING INSTRUCTIONS in Operator’s Manual).
5. Connect the power cord to a 120 volt, 60 cycle, 15-Amp, 3-wire grounded receptacle.

7620917311
MAINTENANCE
The following dispenser maintenance should be performed at the intervals indicated:
DAILY (or as required)
Remove foreign material from vending area drip tray to prevent drain blockage. Clean vending area. Check for
proper water drainage from the vending area drip tray.
MONTHLY
Clean and sanitize the hopper interior and beverage system if applicable (see CLEANING INSTRUCTIONS).
START-UP & OPERATING INSTRUCTIONS
Fill the hopper with ice. Dispense a large cup of ice. Repeat this procedure whenever the dispenser has run out
of ice.
In normal operation, pushing the ice dispenser lever will cause ice to flow from the ice chute. Ice flow will continue
to flow as long as the lever is held depressed.
CAUTION: Use caution to avoid spilling ice when filling dispenser. Clean up immediately any
spilled ice from filling or operating the unit. To prevent contamination of ice, the lid must be
installed on the unit at all times.
If the dispenser fails to dispense ice, see troubleshooting guide.
TORSION BAR REMOVAL
The hinged door as shipped from thje factory is set up for the mountingof Corian on the top. In the cas where Co-
rian will not be used, it is recommended that the rear torsion bar be removed so as to decrease the spring force.
To accomplish this task, the rcommended procedure is as follows.
1. Remove balloon Item 46 Ice Deflector by removing the three knurled screws that hold the Ice Deflectory in
place.
2. Break the RTV seal that holds the polymeric inner lid in place. This should be done with a sharp instrument.
3. Gently pry the inner lid out of the stainless steel cover.
4. Now that the complete Torsion Bar Assembly is visible, locate the Counter Balance Pivot which is balloon
item 71. Using an 11/32” socket or equivalent, remove the two 8-32 hex nuts.
5. Carefully pry the pivot up and away from the mounting studs. As you do this, the torsion shafts will move
along with the pivot.
6. Once the pivot is free of the studs, moving it a little further towards you should allow the torsion shafts to
come free of the pivot.
7. You should be able to grab the rear torsion bar at this time and pull away from the end that is captured in the
sheetmetal bracket.
8. Reverst the steps to reassemble the door.
9. RTV liner back in place.

8
620917311
44
140
24
80
80
119
55
82
81
80
82
119
100
100
79
71
100
29
29
29
46
92
FIGURE 3. TORSION BAR REMOVAL

9620917311
CLEANING AND SANITIZING INSTRUCTIONS
WARNING: Disconnect Power Before Cleaning! Do not use metal scrapers, sharp objects or
abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result.
Do not use solvents or other cleaning agents, as they may attack the plastic material.
Soap solution - Use a mixture of mild detergent and warm (100 F) potable water.
Sanitizing solution - Use 1/2 ounce of household bleach in 1 gallon of potable water. Preparing the sanitizing
solution to this ratio will create a solution of 200 PPM.
DISPENSER
1. CLEANING EXTERIOR SURFACES
Important: Perform the following daily.
A. Remove the cup rest from drip tray.
B. Wash the drip tray with soap solution. Rinse with potable water and allow solution to run down the
drain.
C. Wash cup rest with soap solution and rinse in potable water. Install the cup rest into the drip tray.
D. Clean all exterior surfaces with soap solution and rinse with potable water.
2. CLEANING INTERIOR SURFACES
CAUTION: When pouring liquid into the hopper, do not exceed the rate of 1/2 gallon per
minute.
Important: Perform the following at least once a month.
A. Open right hand hopper cover, then remove all ice from hopper.
B. Lift up and remove the left hand hopper cover.
C. Remove agitator disk and agitator assembly.
D. Remove tower cover by removing three thumb screws.
E. Move the retaining bail to the rear of the tower which will allow removal of the ice chute assembly.
F. Grasp the ice auger by the shaft end and lift out the auger tube. Take care not to damage either end of
the auger.
G. Remove the auger tube by lifting upward. The tube will separate into two halves for easy cleaning when
fully removed.
H. Open the front door of the cabinet below the hopper, this will give you access to the lower auger drive
area and the passage between the hopper and the auger for cleaning.
I. Using the previously prepared detergent solution clean the hopper covers, agitator disk, and agitator
assembly, interior of the hopper, both halves of the ice chute, auger, auger tubes, and the lower auger
area of the auger housing. Thoroughly rinse all of the previously cleaned with potable water.
J. Reassemble the agitator assembly and disc into the hopper. Make certain that the retaining screw is
tight.
K. Using a mechanical spray bottle filled with sanitizing solution, spray the entire interior of the hopper and
the agitator assembly. Go to the lower auger drive area and also spray with sanitizing solution.
Allow to air dry.

10
620917311
L. Using the spray bottle, spray the inside of the two halves of the auger tube, the auger, the two halves of
the chute assembly and the undersides of the right and left covers. Allow to air dry.
M. Reassemble the two halves of the auger tube and place back into its mounting. Holding the auger by the
upper shaft end, insert into the guide tube. Make certain that the auger slips into it drive pin. Chute as-
sembly will not assemble properly if the auger is not seated on its drive pin. Reassemble the upper au-
ger and chute assembly onto the auger and lock down by snapping the bail onto the upper housing. Re-
install the tower cover with the thumb screws.
N. Reinstall the covers. Put the right cover on first before you close the left cover.
65
69
66
74 77
73
75
FIGURE 4. AUGER ASSEMBLY
AUGER ASSEMBLY BREAKDOWN
1. For cleaning, the auger assembly is constructed for simple not tools required breakdown. First remove the
tower cap (item 69) by removing the 3 knurled screws.
2. Once the tower cap is out of the way you will see a wire retainer (item 77). By placing your fingers on the
backside of the ice chute (item 65) with your thumbs pointing upward, place the thumbs on the retainer wire
and with a slight upward movement push the wire retainer towards the rear of the unit. The retainer should
pop out of the saddle and swing backwards.
3. At this point, you should be able to pull up on the ice chute and remove it from the assembly. You will notice
that the ice chute is made up of three pieces. That is the ice chute, the ice chute cover and the auger gate
which is respectively (Items 65, 66, and 69). Take not so that when reassembling the ice chute, the auger
gate cradles in the ice chute with the short tang side up.
4. The auger (Item 73) can now be removed by just grasping it and pulling up. Notice that the bottom of the au-
ger has a depression in the form of a D pattern. When replacing the auger, it will be necessary to rotate the
auger after insertion in the tube to engage the motor shaft.

11 620917311
5. Last are the auger housings (Items 74 and 75). They are dislodged by pulling upward. Check their orientation
and the fact that the longer tube is on the front side. When positioning the housings back in the dispenser,
the longer tube should be placed first so as to seat in the lower housing to set up the orientation (top and bot-
tom are marked on end of the tube tab at the top), otherwise the ice chute spout will not point towards the
front of the dispenser.
ARROW SHOWS CCW DIRECTION FOR INCREASING SPEED OF ICE AUGER MOTOR.
FIGURE 5. ICE AUGER MOTOR
SPEED CONTROL FOR ICE DELIVERY
The ice auger is a variable speed device. A potentiometer is used to control this speed. The potentiometer is lo-
cated in the electrical box which is below the counter.
The output shaft of the potentiometer protrudes through an opening on the bottom side of the electrical box. For
adjustment the output shaft (Items 62 and 59) is easily reached by removing the left side panel cover (item 42).
By turning the knob CCW (counterclockwise), you will increase the speed of the ice delivery. Please note that the
potentiometer position is upside down so the actual motion for increasing the speed if from left to right.

12
620917311
SPEED
POT
POWER CORD
MOTOR HEATER
AGIT MOTOR
HARNESS 33617
W
H
T
DISP
500
CONN
B
L
K
TO
LIFT
MOTOR
B
L
K
W
H
T
TERMINAL
BOARD
24V
TRANSFORMER
B
L
K
CAPACITOR
RECTIFIER
B
L
K
B
L
K
B
L
K
B
L
K
B
L
K
W
H
T
Y
L
WR
E
D
Y
L
W
W
H
T
W
H
T
Y
L
W
G
R
N
R
E
D
B
L
U
P
I
N
K
FILL DOOR
SWITCH
BIN
THERM0STAT LIGHT
OPTION
B
B
L
K
G
R
N
/
Y
L
W
TOP COVER
SWITCH
O
R
G
A
TIMER
BOARD
W
H
T
REMOVABLE
DOOR SWITCH
FIGURE 6. WIRING DIAGRAM

13 620917311
BIN THERMOSTAT
( OPTIONAL)
B
+–
TIMER
BOARD
+
24V
TRANSFORMER
620906403 REV.B
AGIT HTR
G
A
DISP.
SWITCH
INTERLOCKS
MTR HTR
AUG MTR.
FIGURE 7. LADDER DIAGRAM

14
620917311
THIS PAGE LEFT BLANK INTENTIONALLY

15 620917311
TROUBLESHOOTING
IMPORTANT: Only qualified Personnel should service internal components or electrical wiring.
Should your unit fail to operate properly, check that there is power to the unit and that the hopper con-
tains ice. If the unit does not dispense, check the following chart under the appropriate symptoms to
aid in locating the defect.
Trouble Probable Cause
BLOWN FUSE OR CIRCUIT BREAKER. A. Short circuit in wiring.
B. Defective 24 VAC transformer..
C. Defective agitator motor.
D. Shorted motor.
AGITATOR DOES NOT TURN, AUGER DOES NOT
TURN.
A. No power.
B. Bent depressor plate (does not actuate switch).
C. Defective dispensing switch.
D. Defective interlocks, lids not closed.
E. Defective timer board
F. Defective 24 VAC transformer.
ICE DISPENSES CONTINUOUSLY. A. Stuck or bent depressor plate (does not
release switch).
B. Defective dispensing switch.
C. Improper switch installation.
D. Defective timer board.
SLUSHY ICE. WATER IN HOPPER. A. Blocked drain.
B. Unit not level.
C. Poor ice quality due to water quality or
icemaker problems.
D. Improper use of flaked ice.
AGITATOR TURNS, AUGER DOES NOT TURN. A. Defective auger motor.
B. Defective or improper setting of speed control.
C. Defective rectifier.
D. Ice jam.
E. Defective timer board.
AUGER TURNS, AGITATOR DOES NOT. A. Defective agitator motor.
B. Defective motor capacitor.
C. Defective timer board.

Part # Corrections/Update Document
Unit Type/Model # Manual #
OPERATORS MANUAL
ICE DISPENSER UC150
ICE ONLY
620917311
Revision 2 2/10/06
Page Item Old Part Desc. New Part Desc. Agent Date Notes
21 57 620305201 AUGER MOTOR 629087456
629087489
629087431
SUPER SEAL
MOTOR KIT
OR
MOTOR &
SUPER SEAL
ASY KIT
OR
KIT SEAL
REPLACEMENT
UCXX
Jls 03/10/03 Motor w/ceramic
seal and lower
housing.
Motor with seal
installed (no lower
housing).
Contains the seal
only.
21 58 620305202 AGITATOR
TIMER
620311701 AGITATOR
TIMER BOARD
ONLY
Jls 01/22/03 If unit has old timer
board on it must
order Timer Board
Update Kit
629087410.
n/a n/a n/a 620045952 AUGER MOTOR
MOUNTING
BRACKET
Jls 01/22/03
n/a n/a n/a 620046706 REMOVABLE ICE
BASKET
HOLDER
Jls 01/22/03
n/a n/a n/a 620504025 HINGE COVER
ASSY
n/a n/a n/a 629087428 TOWER BASE
REPAIR KIT
Jls 01/22/03 Used if base breaks.
Kit contains support
brackets that hold
ice chute retainer in
place.
n/a n/a 629085201 DOOR ASSY RH
KIT
Jls 01/22/03
n/a n/a 620048801 DOOR ASSY LH Jls 01/22/03
n/a n/a 620506540 HINGE END CAP Jls 01/22/03
n/a n/a 620503702 DRIP TRAY Jls 01/22/03
n/a n/a 620024906 LATCH HANDLE
ASSY
Jls 01/22/03

16620917311
6
1
2
3
4
5
9
10
13
15
16
17
29
30
36
38
39
40
43
44
45
46
47
48
49 50
51
52
53
54
55
56
57
58
59
62
63
64
65
66
67
68
69
71
73
74
75
76
77
78
79
81
82
83
84
85
87
90
91
92
93
94
95
97
98
99
100
101
102
103
104
105
107
108
110
111
112
113
114
115
118
118
121
126
131
16
29
29
41
62
78
80
89
97
97
99
99
100
100
100 100
102
105
105
108
108
108
108
108
120
120
97
16
13
13
89
80
82
89
121
24
141
24
140
91
131
14 106
136
136
FIGURE 8. US 150 EXPLODED VIEW

17 620917311
AGITATOR MOTOR HEATER WIRING DETAIL
MOTOR HEATER
FROM E–BOX
106
14
BLK
BLK
BLK
RED
WHT
TERMINAL
BOARD IN E–BOX
NOTE:
LOCATE HEATER ON
GEAR BOX HOUSING
6
CLEAR BOOT
MUST COVER
BOTH TERMINALS
RED WIRE CONNECT
TO NORMALLY OPEN
BLACK WIRE
CONNECT TO
COMMON
COM.
N.O.
DISPENSE SWITCH WIRING DETAIL
FIGURE 9. AGITATOR MOTOR AND DISPENSE SWITCH WIRING DETAIL