Hotel Fitness TR9800-E User manual

CAUTION
Read all precautions and in-
structions in this manual before
using this equipment. eep this
manual for future reference.
Model No. HF-TR9800-E.0
Serial No. __
The serial number is found in the
location shown below. Write the
serial number in the space above.
QUESTIONS?
If you have questions, or if parts are
damaged or missing, please see
HOW TO CONTACT CUSTOMER
CARE on the back cover of this
manual.
Serial
Number
Decal
USERʼS MANUAL
www.HotelFitness.com

2
TABLE OF CONTENTS
WARNIN DECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS .................................................................3
BEFOREYOUBE IN .......................................................................5
ASSEMBLY ...............................................................................6
HOWTOUP RADETHECONSOLE..........................................................10
HOWTOMOVETHETREADMILL ............................................................10
TREADMILLOPERATION...................................................................11
PREVENTIVEMAINTENANCE ...............................................................22
SIX-MONTHPREVENTIVEMAINTENANCERECORD ............................................25
TROUBLESHOOTIN ......................................................................26
EXERCISE UIDELINES ...................................................................28
PARTLIST ...............................................................................29
EXPLODEDDRAWIN .....................................................................31
HOWTOCONTACTCUSTOMERCARE................................................BackCover
LIMITEDWARRANTY...............................................................BackCover
WARNING DECAL PLACEMENT
Note: There is one decal on
each side.
This drawing shows the loca-
tions of the warning decals. If a
decal is missing or illegible,
see the back cover of this
manual and request a free re-
placement decal. Apply the
decal in the location shown.
Note: The decals may not be
shown at actual size.
HOTEL FITNESS is a registered trademark of Hotel Fitness Club, Inc.
FREEMOTION is a registered trademark of ICON IP, Inc.

3
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described in this
manual.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. eep the treadmill indoors, away from mois-
ture and dust. Do not place the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Do not operate the treadmill until it is prop-
erly assembled (see ASSEMBLY on page 6).
8. Inspect and properly tighten all parts of the
treadmill regularly.
9. eep children under age 12 and pets away
from the treadmill at all times.
10. The treadmill should be used only by per-
sons weighing 350 lbs. (159 kg) or less.
11. Do not allow more than one person on the
treadmill at a time.
12. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
13. When connecting the power cord (see page
11), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
14. Use only a single-outlet surge suppressor
that meets all the specifications described on
page 11. To purchase a surge suppressor,
please see the back cover of this manual and
order part number 146148, or see your local
electronics store.
15. Failure to use a properly functioning surge
suppressor could result in damage to the
control system of the treadmill. If the control
system is damaged, the walking belt may
slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
16. eep the power cord away from heated sur-
faces.
17. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 26 if the treadmill is
not working properly.)
18. Read, understand, and test the emergency
stop procedure before using the treadmill
(see page 13).
19. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
20. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. Hotel Fitness
and FreeMotion Fitness assume no responsibility for personal injury or property damage sustained
by or through the use of this product.
IMPORTANT PRECAUTIONS

4
21. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the “off” position when the tread-
mill is not in use. (See the drawing on page 5
for the location of the reset/off circuit
breaker.)
22. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
23. Do not change the incline of the treadmill by
placing objects under it.
24. Never insert or drop any object into any
opening on the treadmill.
25. Make sure to perform all maintenance proce-
dures outlined in this manual. Failure to do
so will void the warranty and may result in
damage to the treadmill.
26. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Servicing other than
the procedures in this manual should be per-
formed by an authorized service representa-
tive only.
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the new HOTEL FITNESS®
TR9800-E treadmill. The TR9800-E treadmill offers an
impressive array of features designed to help you
achieve your fitness goals.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the back cover of this
manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
BEFORE YOU BEGIN
Handrail
Accessory Tray Console
Key/Clip
Reset/Off Circuit
Breaker
Walking Belt
Foot Rail
Power Cord
Platform Cushion
Roller
Adjustment
Bolts

6
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is
coated with high-performance lubricant. After shipping, some lubricant may be found on top of the walking belt or
on the shipping carton. This is normal and does not affect performance. If there is lubricant on top of the walking
belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly can be completed using a 7/32" hex key and an adjustable wrench .
Use the drawings below to identify assembly hardware. The number in parentheses below each drawing is the key
number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the
quantity needed for assembly. If a part is not in the hardware kit, see if it is preattached to one of the parts to
be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools.
ASSEMBLY
1/2" Jam Nut (5)–4
1/2" Star
Washer (7)–4
3/8" Star
Washer (9)–4
3/8" Nut (42)–2 3/8" Wheel
Washer (57)–2
5/16" Star
Washer (8)–4
3/8" x 2" Bolt (3)–4
1/2" x 3 1/4" Bolt (1)–4
3/8" x 2 1/2" Wheel
Bolt (34)–2
5/16" x 1" Bolt (2)–8
1. Note: The Wheels (91) may be preattached. If
they are not, complete this step.
With the help of a second person, carefully raise
the Uprights (96) and insert a Wheel (91) into
the lower end of each Upright. Be careful not to
pinch the 55" Wire Harness (48).
Attach each Wheel (91) with a 3/8" x 2 1/2"
Wheel Bolt (34), a 3/8" Wheel Washer (57), and
a 3/8" Nut (42) (only one side is shown). Do not
overtighten the Nuts; the Wheels must turn
freely.
57
34
42
96
48 91
1

7
4. Attach each side of the Uprights (96) to the
Base Frame (75) with two 1/2" x 3 1/4" Bolts (1),
two 1/2" Star Washers (7), and two 1/2" Jam
Nuts (5) (only one side is shown). Start all four
Bolts before tightening any of them.
2. Place the Uprights (96) near the front of the
Base Frame (75). Have a second person tip the
Uprights back so that they roll on the Wheels
(91) as shown.
Connect the 80" Wire Harness (46) in the Base
Frame (75) to the 55" Wire Harness (48) in the
right Upright (96). See the inset drawing. The
connectors should slide together easily and
snap into place. If they do not, turn one con-
nector and try again. IF THE CONNECTORS
ARE NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON. Be careful not to
pinch your fingers or the wire harnesses.
96
75
48
46
2
46
48
91
3. ently pull the 55" Wire Harness (48) up
through the right Upright (96) while a second
person rolls the Uprights toward the Base Frame
(75).
Align the indicated holes in the Uprights (96)
above the holes in the Base Frame (75). Lower
the Uprights onto the Base Frame. Be careful
not to pinch your fingers or the wire har-
nesses. Make sure to keep the holes aligned.
75
96
48
48
3
75
1
7
96
7
4
5
Holes

8
6. Have a second person hold the Handrail (100)
near the Upright Brackets (98, 99). Connect the
TV cables in the Handrail to the TV cables in the
Left Upright Bracket.
Connect the 55" Wire Harness (48) in the Right
Upright Bracket (98) to the 35" Wire Harness
(47). See the inset drawing in step 2. The
connectors should slide together easily and
snap into place. If they do not, turn one con-
nector and try again. IF THE CONNECTORS
ARE NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
Insert the Wire Harnesses (47, 48) and each of
the TV cables into the Handrail (100) as you set
the Handrail on the Upright Brackets (98, 99).
Be careful not to pinch the wires.
Attach the Handrail (100) to the Upright
Brackets (98, 99) with four 5/16" x 1" Bolts (2)
and four 5/16" Star Washers (8). Start all four
Bolts before tightening any of them.
2
99
47
98
48
100
22
8
8
8
2
6
TV
Cables
5. Note: The Upright Brackets (98, 99) may be
preattached. If they are not, complete this
step.
Insert the TV cables through the Left Upright
Bracket (99). Press the Left Upright Bracket
onto the left Upright (96). Be careful not to
pinch the cables.
Insert the 55" Wire Harness (48) through the
Right Upright Bracket (98). Press the Right
Upright Bracket onto the right Upright (96). Be
careful not to pinch the Wire Harness.
Attach each Upright Bracket (98, 99) with two
3/8" x 2" Bolts (3) and two 3/8" Star Washers (9).
99
3
9
3
98
9
96
48
5
TV
Cables

9
9. Remove the three #8 x 1/2" Console Cover
Screws (121) from the Console Cover (105).
Discard the Console Cover.
105
121
9
If you purchased the optional personal television, follow the additional steps below.
10. Have a second person hold the TV Console
(120) near the Console Back (49). Connect the
TV cable (A) in the TV Console to the 45" TV
Cable (125) in the Console Back.
Connect the wire harness (B) in the TV Console
(120) to the wire harness (C) in the Console
Back (49). See the inset drawing in step 2.
The connectors should slide together easily
and snap into place. If they do not, turn one
connector and try again. IF THE CONNEC-
TORS ARE NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
Attach the TV Console (120) to the Console
Back (49) with the #8 x 1/2" Console Cover
Screws (121) that you removed in step 9. Be
careful not to pinch the wires.
121 120
A
B
49
125
C
10
8. Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or car-
pet, place a mat beneath the treadmill.
7. Attach the Front Roller Cover (68) with four
5/16" x 1" Bolts (2).
68
2
2
7

This console features an optional personal television, which offers additional functionality. With the optional per-
sonal television, you can watch the television programs of your choice, or connect and use your own VCR or
DVD player. To purchase the optional personal television, please see the back cover of this manual.
HOW TO UPGRADE THE CONSOLE
HOW TO MOVE THE TREADMILL
Unplug the power cord. Note: It may be necessary to
disconnect an audio/video cable from the treadmill. Due
to the size and weight of the treadmill, moving it re-
quires two or three persons.
Hold the metal frame firmly in the location shown at
the right. CAUTION: To decrease the possibility of
damage to the treadmill or of injury, do not lift the
frame by the plastic front cover or by the handrail.
Carefully roll the treadmill on the wheels to the desired
location and then lower it to the level position. CAU-
TION: To reduce the risk of injury, use extreme cau-
tion while moving the treadmill. Do not attempt to
move the treadmill over uneven surfaces.
After the treadmill is placed in the location where it will
be used, make sure that the leveling feet and the base
pads rest firmly on the floor (only one side is shown). If
the treadmill rocks even slightly, turn one of the leveling
feet clockwise or counterclockwise until the rocking mo-
tion is eliminated.
Frame
Wheels
Leveling
Foot
Base Pad
Leveling Foot
10

11
TREADMILL OPERATION
THE PRE-LUBRICATED WAL ING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply
substances to the walking belt or the walking plat-
form. Silicone spray and other substances will de-
teriorate the walking belt and cause excessive
wear.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the possi-
bility of your treadmill being damaged, always use
a surge suppressor with your treadmill (see draw-
ing 1 at the right). To purchase a surge suppres-
sor, please see the back cover of this manual and
order part number 146148, or see your local elec-
tronics store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may slow, accelerate, or stop unex-
pectedly, which may result in a fall and serious in-
jury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
rounded Outlet Box
rounded Outlet Box
rounding Plug
Surge Suppressor
Surge Suppressor
rounding Pin
Adapter
Lug
Metal Screw
rounded Outlet
rounding Pin
rounding Plug

12
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When you use the manual mode of
the console, you can change the speed and incline of
the treadmill with the touch of a button. As you exer-
cise, the console will display continuous exercise feed-
back.
In addition, the console features fourteen personal
trainer workouts. Each preset workout automatically
controls the speed and incline of the treadmill as it
guides you through an effective workout.
The console also offers twelve interactive trainer work-
outs that allow you to customize your workout. The in-
teractive trainer workouts include three heart rate
workouts that control the speed and incline of the
treadmill to keep your heart rate near the target heart
rate settings. In addition, three fitness test workouts
measure your fitness level or your VO2max.
The console also features the new iFit interactive
workout system. The iFit system is compatible with iFit
interactive workout cards containing workouts de-
signed to help you achieve specific fitness goals. For
example, lose unwanted pounds with the iFit Weight
Loss program, or train for a long-distance run with the
iFit Marathon program. iFit programs automatically
control the speed and incline of the treadmill. To pur-
chase iFit cards, please see the back cover of this
manual or go to www.iFit.com. iFit cards are also
available at select stores.
Whether you select the manual mode or a preset work-
out, you can watch the television programs of your
choice on the optional personal television. You can
even listen to your favorite workout music or audio
books with the consoleʼs stereo sound system.
To turn on the power, see on page 13. To use the
manual mode, see page 13. To use a personal
trainer workout, see page 15. To use a walk/run
workout or a manual control workout, see page 16.
To use a fitness test workout, see page 17. To use
a heart rate workout, see page 18. To use a custom
workout, see page 19. To use an iFit workout, see
page 20. To use the maintenance mode, see page
21. To use the stereo sound system, see page 21.
CONSOLE DIAGRAM

13
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord
(see page 11). Next, lo-
cate the reset/off circuit
breaker on the treadmill
frame near the power
cord. Make sure that the
circuit breaker is in the
“reset” position.
Next, stand on the foot
rails of the treadmill.
Locate the clip attached to
the key (see the drawing
at the right), and slide the
clip securely onto the
waistband of your clothes.
Then, insert the key into
the console. After a mo-
ment, the displays will light. IMPORTANT: In an emer-
gency situation, the key can be pulled from the
console, causing the walking belt to slow to a stop.
Test the clip by carefully taking a few steps back-
ward; if the key is not pulled from the console, ad-
just the position of the clip.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To pre-
vent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment
of the walking belt, and center the walking belt if
necessary (see page 27).
Note: Your console will display speed and distance in
either miles or kilometers. For simplicity, all instruc-
tions in this section refer to miles.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
Each time the key
is inserted, the
manual mode will
be selected. If you
have selected a
workout, press any
of the workout buttons repeatedly until zeros ap-
pear in the display.
3. Start the walking belt and adjust the speed.
To start the walking belt, press the Start/Stop but-
ton, the Speed increase button, or one of the Quick
Touch Speed buttons numbered 1 to 12. As you
exercise, change the speed of the walking belt as
desired by pressing the Speed increase and de-
crease buttons next to the Start/Stop button. Each
time you press one of the buttons, the speed set-
ting will change; if you hold down one of the but-
tons, the speed setting will change in larger incre-
ments. After you press one of the Quick Touch
Speed buttons, press the Enter button or press the
speed button again to confirm the speed.
To stop or restart the walking belt, press the
Start/Stop button.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase or decrease button. Each time you
press one of the buttons, the incline will gradually
change until it reaches the selected incline setting.
Reset
Position
Clip
Key

14
5. Select a display mode and monitor your
progress with the display.
When the manual
mode is selected,
the console offers
seven display
modes. The dis-
play mode that you
select will determine which workout information is
shown. Press the Display button repeatedly to se-
lect the desired display mode.
As you walk or run on the treadmill, the upper dis-
play can show the following workout information:
• The elapsed time.
• The distance that you have walked or run.
• The speed of the walking belt.
• The incline level of the treadmill.
• The approximate number of calories you have
burned.
• The approximate number of calories burned per
hour.
• Your exercise intensity in METs. One MET is the
amount of energy you use while resting.
• Your walking or running pace, in minutes per
mile or minutes per kilometer.
• Your power output in watts.
• An animation of a road.
Regardless of which display mode you select, the
speed or incline setting will appear in the display
for a few seconds each time you change the set-
ting.
As you switch between workouts and the manual
mode, the console will keep track of the total dis-
tance that you have walked or run and the approxi-
mate number of calories you have burned. You can
keep your totals even when you switch to a new
workout. To reset the console, press the Clear but-
ton.
6. Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from
the metal con-
tacts. In addi-
tion, make
sure that your
hands are clean.
To measure your heart rate, stand on the foot
rails and hold the contacts for approximately
ten seconds—avoid moving your hands. When
your pulse is detected, your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
7. Turn on the fan if desired.
The fan has high and low speed settings. Press the
Fan button repeatedly to select a fan speed or to
turn off the fan. Note: If the fan is on when the
walking belt stops, the fan will automatically turn off
after a few minutes.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, re-
move the key from the console, and put it in a se-
cure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
Contacts

15
HOW TO USE A PERSONAL TRAINER WOR OUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2. Select one of the personal trainer workouts.
To select a per-
sonal trainer work-
out, press the
Random Workouts
button, the Interval
Workouts button,
or the Terrain Workouts button repeatedly until the
name of the desired workout appears in the dis-
play. Random workouts use preset random speed
and incline settings. Interval workouts use speed
settings to provide a personalized workout. Terrain
workouts use speed and incline settings to simu-
late an actual walking experience.
When a workout is selected, the display will show
the name, the maximum incline setting, the maxi-
mum speed setting and the duration of the work-
out. The display will also show a profile of the
speed settings of the workout. Press the Enter but-
ton to select the desired workout.
Select your age, your weight, and the workout du-
ration using the Increase and Decrease buttons
next to the Enter button. Press the Enter button
after each selection. Note: To use the Interval
workouts, you must also enter your minimum and
maximum speed settings using the Quick Touch
Speed buttons or the Speed increase and de-
crease buttons.
3. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the treadmill
will automatically adjust to the first speed and in-
cline settings of the workout. Hold the handrails
and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed and/or in-
cline setting may be programmed for consecutive
segments. Note: If you use an Interval workout, the
incline will not adjust automatically.
During the workout, the profile will show your
progress. The flashing segment of the profile rep-
resents the current segment of the workout. The
height of the flashing segment indicates the speed
setting for the cur-
rent segment. At
the end of each
segment, the next
segment of the pro-
file will begin to
flash and the speed
and incline settings will appear at the top of the dis-
play for a few moments to alert you. The treadmill
will then automatically adjust to the new speed and
incline settings.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Speed or
Incline buttons; however, when the next segment
of the workout begins, the treadmill will auto-
matically adjust to the speed and incline set-
tings for the next segment.
To stop or restart the workout at any time, press
the Start/Stop button.
4. Select a display mode and monitor your
progress with the display.
The console offers three display modes. The dis-
play mode that you select will determine which
workout information is shown. Press the Display
button repeatedly to select the desired display
mode.
The display can show the speed of the walking
belt, the incline of the treadmill, a profile of the
workout, the time remaining in the workout, the dis-
tance you have walked or run, the approximate
number of calories you have burned, your exercise
intensity in METs, the approximate number of calo-
ries burned per hour, your pace, and your power
output in watts.
5. Measure your heart rate if desired.
See step 6 on page 14.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
Current Segment

16
HOW TO USE A WAL /RUN WOR OUT OR A
MANUAL CONTROL WOR OUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2. Select one of the workouts.
To select a walk/run workout, press the Walk/Run
Workouts button repeatedly until the 5K Walk, the
10K Walk, or the Cross Country workout appears
in the display.
To select a manual
control workout,
press the Manual
Control button re-
peatedly until the
Manual Time, the
Manual Distance, or the Manual Calories workout
appears in the display.
The display will show the name, the maximum in-
cline setting, the maximum speed setting, and the
duration of the workout. Press the Enter button to
select the desired workout.
Select your age and then your weight using the
Increase and Decrease buttons next to the Enter
button. Press the Enter button after each selec-
tion. Note: To use the cross country workouts, you
must also enter your distance goal. To use a man-
ual control workout, enter your time, distance, or
calorie goal.
3. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the treadmill
will begin moving. Hold the handrails and begin
walking.
During the workout, the profile will show the speed
of the walking belt. As you exercise, change the
speed and incline of the walking belt as desired by
pressing the Speed and Incline increase and de-
crease buttons.
The workout will continue until you reach your time,
distance, or calorie goal. The walking belt will then
slow to a stop.
To stop or restart the workout at any time, press
the Start/Stop button.
4. Select a display mode and monitor your
progress with the display.
See step 4 on page 15.
5. Measure your heart rate if desired.
See step 6 on page 14.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.

17
HOW TO USE A FITNESS TEST WOR OUT
The fitness test workouts measure your relative fitness
level. For the most accurate results, use a fitness test
workout when you are not feeling tired, when you have
not eaten for at least two hours, and when you have
not exercised for at least 24 hours.
The treadmill features three fitness workouts. The
Ebbeling Fitness Test measures VO2max, or aerobic
capacity, and lasts 9 minutes. The erkin Fitness Test
also measures VO2max. The erkin Fitness Test be-
gins with a three-minute warm-up period and ends
after either 14 minutes or when you reach a certain
heart rate. The FreeMotion Fitness Test measures
your fitness level on a scale of 1 to 10, where 10 is the
highest fitness level. The FreeMotion Fitness Test
ends after either 28 minutes or when you reach a cer-
tain heart rate.
1. Put on a Polar®-compatible chest pulse sensor
(not included).
To use a fitness test, you must wear a Polar-com-
patible chest pulse sensor or use the handgrip
pulse sensor. Note: For best results, you should
wear a chest pulse sensor. No chest pulse sensor
is included.
2. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 13.
3. Select a fitness test workout.
To select a fitness test workout, press the Fitness
Tests button repeatedly until the name of the de-
sired fitness test appears in the display. Press the
Enter button to select the desired workout.
Select your age and then your weight using the
Increase and Decrease buttons next to the Enter
button. Press the Enter button after each selec-
tion. Note: To use the Ebbeling Fitness Test, you
must also enter your gender.
4. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the treadmill
will automatically adjust to the first speed and in-
cline settings of the fitness test. Begin walking on
the treadmill. Note: For the most accurate results,
do not hold the handrails during a fitness test work-
out.
During the workout, the speed and incline of the
treadmill will periodically change. The speed set-
ting or the incline setting will appear in the display
to alert you before each change. IMPORTANT:
The Speed and Incline buttons will not function
during a fitness test workout.
Note: If you press the Start/Stop button during the
fitness test, the fitness test will end.
When the workout ends, the walking belt will slow
to a stop and your fitness level or VO2max will ap-
pear in the display.
If your pulse is not detected during the workout, the
words CHECK HEART RATE MONITOR will ap-
pear in the display and the speed of the treadmill
may automatically decrease. If your pulse is still
not detected, the fitness test will be aborted.
5. Select a display mode and monitor your
progress with the display.
See step 4 on page 15. Note: The fitness tests will
display your fitness level instead of your exercise
intensity in METs.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.

18
HOW TO USE A HEART RATE WOR OUT
1. Put on a Polar®-compatible chest pulse sensor
(not included).
To use a heart rate program, you must wear a
Polar-compatible chest pulse sensor or use the
handgrip pulse sensor. Note: For best results, you
should wear a chest pulse sensor. No chest pulse
sensor is included.
2. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
3. Select one of the heart rate workouts.
To select a heart rate workout, press the Heart
Rate Control button repeatedly until the desired
workout appears in the display. Press the Enter
button to select the desired workout.
Select your age and then your weight using the
Increase and Decrease buttons next to the Enter
button. Press the Enter button after each selec-
tion. Note: To use the constant heart rate and vari-
able heart rate workouts, you must also enter your
target maximum heart rate. If the target maximum
heart rate setting is changed, the intensity level of
the entire workout will change. Note: To calculate
your target maximum heart rate see EXERCISE
INTENSITY on page 28.
4. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the walking belt
will begin to move and the treadmill will automati-
cally adjust to the first speed and incline settings of
the workout. Hold the handrails and begin walking.
The heart rate workouts are divided into several
one-minute segments. One target heart rate setting
is programmed for each segment. The same target
heart rate setting may be programmed for consec-
utive segments. For a shorter workout, simply stop
the workout before it ends.
During all heart rate workouts, the console will reg-
ularly compare your heart rate to the target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting for the current
segment, the speed of the walking belt will auto-
matically increase or decrease to bring your heart
rate closer to the target heart rate setting.
If the speed or incline setting is too high or too low
at any time during the workout, you can adjust the
setting with the Speed or Incline buttons; however,
each time the console compares your heart
rate to the target heart rate setting, the speed
of the treadmill may automatically change to
bring your heart rate closer to the target heart
rate setting.
To stop or restart the workout at any time, press
the Start/Stop button.
5. Select a display mode and monitor your
progress with the display.
See step 4 on page 15.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
CAUTION: If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the pulse work-
outs. If you are taking medication regularly,
consult your physician to find out whether the
medication will affect your exercise heart rate.

19
HOW TO USE A CUSTOM WOR OUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2. Select one of the custom workouts.
To select a custom workout, press the Custom
Workouts button repeatedly until the desired work-
out appears in the display.
The display will show the name, the maximum in-
cline setting, the maximum speed setting, and the
duration of the workout. Note: To create a custom
workout, see step 3 on page 21.
Press the Enter button to select the desired work-
out. Select your age and then your weight using
the Increase and Decrease buttons next to the
Enter button.
3. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the treadmill
will automatically adjust to the first speed and in-
cline settings that you programmed previously.
Hold the handrails and begin walking.
Each custom workout is divided into one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment.
During the work-
out, the profile will
show your
progress. The
flashing segment
of the profile repre-
sents the current
segment of the workout. The height of the flashing
segment indicates the speed setting for the current
segment. At the end of each segment, a series of
tones will sound, the next segment of the profile
will begin to flash, and the speed and incline set-
tings for the next segment will appear in the display
to alert you. The treadmill will then automatically
adjust to the new speed and incline settings.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or in-
cline buttons; however, when the next segment
of the workout begins, the treadmill will auto-
matically adjust to the speed and incline set-
tings for the next segment.
To stop or restart the workout at any time, press
the Start/Stop button. The speed of the walking
belt will gradually adjust to the speed setting for the
current segment.
4. Select a display mode and monitor your
progress with the display.
See step 4 on page 15.
5. Measure your heart rate if desired.
See step 6 on page 14.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
Current Segment

20
HOW TO USE AN IFIT WOR OUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2. Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the
iFit slot in the back of the console; make sure that
the iFit card is oriented so the missing corner is
facing downward and is inserted into the iFit slot.
Next, select an iFit workout by pressing the
Increase and Decrease buttons next to the Enter
button. When an iFit workout is selected, the dis-
play will show the name, the maximum incline set-
ting, the maximum speed setting, and the duration
of the workout.
Each iFit workout is divided into one-minute seg-
ments. One speed setting and one incline setting
are programmed for each segment. Note: The
same speed and/or incline setting may be pro-
grammed for consecutive segments.
3. Start the walking belt.
Press the Start/Stop button to start the workout. A
moment after you press the button, the treadmill
will automatically adjust to the first speed and in-
cline settings of the workout. Hold the handrails
and begin walking.
At the end of each one-minute segment, the speed
and incline settings for the next segment will ap-
pear in the display and a series of tones will sound
to alert you. If a different speed or incline setting is
programmed for the next segment, three tones will
sound. The treadmill will then automatically adjust
to the new speed and incline settings.
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually over-
ride the setting by pressing the Speed or Incline
buttons; however, when the next segment be-
gins, the treadmill will automatically adjust to
the speed and incline settings for the next seg-
ment.
To stop the workout at any time, press the
Start/Stop button. To restart the workout, press the
Start/Stop button or the Speed increase button.
The walking belt will begin to move. When the next
segment of the workout begins, the treadmill will
automatically adjust to the speed and incline set-
tings for the next segment.
4. Select a display mode and monitor your
progress with the display.
See step 4 on page 15.
5. Measure your heart rate if desired.
See step 6 on page 14.
6. Turn on the fan if desired.
See step 7 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
CAUTION: Always remove iFit cards from the
iFit slot when you are not using them.
iFit Slot
iFit Card